CrimeStopper Super Page V CS-2014TW2 Bedienungsanleitung

CS-2014TW2 Super Page V™

2-Way AM/FM LCD Paging Alarm & Remote Engine Starting System

OPERATION INSTRUCTIONS

INTRODUCTION

CONGRATULATIONS on your choice of the SuperPage V™ by Crimestopper Security Products Inc. This booklet

contains the information necessary for operating your system. If any questions arise, contact your installation dealer or

Crimestopper Security Products Inc.

*IMPORTANT INFORMATION: Primary and Optional Features

-PRIMARY: These features must be connected in order for the system to operate properly i.e. Power, Ground, LED,

etc.

-OPTIONAL: Optional features are connected only if desired or agreed upon by the installing dealer i.e. Horn Honk,

Dome light illumination, Door Locks, Trunk Pop, etc. These features may require additional parts and labor charges.

Consult with your installer about these features BEFORE installation!

CONTACT INFORMATION:

TECHNICAL SUPPORT (800)-998-6880

Monday -Friday 8:00am -4:30pm Pacific

Website: www.crimestopper.com

E-mail: tech-support@crimestopper.com

CRIMESTOPPER

SECURITY PRODUCTS, INC.

1770 S. TAPO STREET

SIMI VALLEY, CA. 93063 REV. A102.01.2005

This device complies with FCC Rules part 15. Operation is subject

to the following two conditions: 1) This device may not cause

interference, and (2) this device must accept any interference that

may be received, including interference that may cause undesired

operation. The manufacturer is not responsible for any radio or TV

interference caused by unauthorized modification to this

equipment. Such modification could void the user's authority to

operate the equipment.

TABLE OF CONTENTS

Operation Cautions & Warnings……..…………..……………………………………………………………………2

Transceiver / Pager-Remote……….....…………..……………………………………………………………………3

CS-416TW Sidekick Remote Control…………………….…………………………………………………..…...…..4

Operating Instructions -Alarm……………………………………………………….………..……………..……..5-8

Remote Engine Control………………………...……………………………………………….…….………...….9-12

Anti-Carjack Protection...……………………………………….………….……..………………..………..………..13

LED Diagnostics………………..……………………………………………………………………….………..….…14

Transceiver / Remote Control Programming……………………………………………………..……………14-15

2 Vehicle Operation……...………………………….……………………………….………….…………….….……16

Troubleshooting / FAQ Section……………….…………………………………………………………..……..17-18

Low Battery Warning–LCD Remote / Setting Clock –LCD Remote……………………………….….……..19

OPERATION CAUTIONS & WARNINGS

CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident

resulting from the use of this equipment. This system is designed to be professionally installed into a car or

vehicle in good running order. Items, such as parking brake, door switches, and all engine safety features,

must be in perfect working condition.

DAMAGE resulting from misuse or negligence is NOT covered under warranty and will be subject to

repair and / or replacement charges.

IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this

system and its safety features. B) Check for proper operation of these safety features prior to accepting

delivery of the vehicle from the installation facility. C) Check and maintain the condition of the vehicle and all

items relative to the proper operation of this system and its safety features.

DO NOT remote start the vehicle in a closed garage. Make sure that the vehicle is outdoors, a garage door

is open, or there is adequate exhaust ventilation. Failure to observe this rule could result in injury or death

from poisonous Carbon Monoxide fumes. This is especially important when using the Timed Self-Start feature

of the unit

#2 DISARM

UNLOCK

LCD

SCREEN

#4 ENGINE

START/STOP

#1 ARM

LOCK

#3 TRUNK

#5 RECALL

CAR I or II

FIXED

ANTENNA

BUTTON 5

(On side of remote):

•Press and release to light up

the LCD screen.

•Press and release twice to

recall the last message from

the LCD screen.

•Press and Hold two seconds

to change from Car 1 to Car 2

•Press 5 times to change the

Time and audible beep tones

on the remote.

TRANSCEIVER / PAGER-REMOTE

PAGER / REMOTE TRANSCEIVER:

The hand-held remote transceiver is used to send and

receive information from the vehicle. The Control Module

transmits High Frequency AM/FM signals from the vehicle

to your over long distances. Your range will vary depending

on location, terrain, and local RF noise/interference. This

system is not guaranteed to page you if you are behind

concrete walls, underground, in a large structure, or in an

area with high levels of electronic interference. Handle the

pager/remote with care if the LCD display and/or the

electronics may be damaged if subjected to abuse. The

AAA Cell 1.5V alkaline battery can easily be replaced by

sliding open the battery access door on the back of the

remote. Battery life will vary depending on usage. The

LCD screen will display a low battery icon when the battery

is low. For more see “Range Questions” on page 17.

BUTTON 1(Lock Symbol):

•Press and release to Arm/Lock system.

•Press and Hold for more than 3 seconds to activate “Panic” feature.

BUTTON 2 (Unlock Symbol):

•Press and release to Disarm/Unlock system, or reset a cycle.

BUTTON 3 (Trunk Symbol):

•Press and Release to activate trunk pop (Auxiliary output #1) Optional

Feature.

•Press and Hold to activate a second optional feature (Auxiliary output

#2).

BUTTON 4 (StartKey Symbol):

•Press and release to Start/Stop engine.

CrimeStopper

LOCK/

TRUNK

REMOTE

UNLOCK/

VEHICLE 2

FLASHLIGHT

START

ARM

DISARM

CS-416TW SIDEKICK REMOTE

The CS-416TW1-Way sidekick remote adds flexibility to your CS-2014TW2. You can have the convenience

of operating your system without needing to carry

the larger pager remote. The Sidekick remote has

less range and offers all of the same operation

features except for page-back confirmation.

BUTTON 1(Lock Symbol):

•Press and release to Arm/Lock system.

•Press and Hold for more than 3 seconds to

activate “Panic” feature.

BUTTON 2 (Unlock Symbol):

•Press and release to Disarm/Unlock system, or

reset a cycle.

BUTTON 3 (Trunk Symbol):

•Press and Release to activate trunk pop

(Auxiliary output #1) Optional Feature.

•Press and Hold to activate a second optional

feature (Auxiliary output #2).

BUTTON 4 (StartKey Symbol):

•Press and release to Start/Stopengine.

BUTTON 5 (Upper side button of remote):

•Press for convenient flashlight function. The high-power LED acts as a mini flashlight.

BUTTON 6 (Lower side button of remote):

•Press and release to activate Vehicle #2 mode. (Led will flash for 4 second to use vehicle #2, otherwise

remote will revert back to Vehicle #1

ARM-LOCK

OPERATING INSTRUCTIONS -ALARM

Active Arming / Locking:

Press button #1 (Lock symbol) on the transceiver. The System will arm emit one siren chirp,

one light flash, and the LED will begin to flash. Power locks will lock (if equipped). Starter

disable circuit will turn on. LCD Pager will beep once while displaying a Locking symbol.After

a short delay to allow the vehicle and electronics to settle, the system will be completely

armed.

Disarming: / Unlocking

Press button #2 (Unlock symbol) on the transceiver. System will disarm and confirm with two

siren chirps, two light flashes, and the LED will turn off. Power locks will unlock and Interior

Dome light will turn on (if installed with these optional features). LCD Pager will beep twice

while displaying an Unlock symbol.

Alarm Triggers:

If there is an intrusion into the vehicle, a hard impact to the body or the ignition is turned on,

the alarm will sound and flash the lights for 1 minute. After 1 minute, the trigger cycle will

automatically stop and alarm will remain armed to continue protecting the vehicle. If a door is

left open after an intrusion then the unit will cycle a maximum of 2minutes and continue to

protect the other un-tampered or unopened zones.

LCD Remote Paging / Zone Violations:

When the system is triggered, the alarm sends a paging signal to the remote. If you are within

range, you will receive a violation paging signal that consists of a vibration followed by 15

audible beeps to notify you the vehicle has been tampered with.

SHOCK SENSOR

DOOR TRIGGER

IGNITION TRIGGER

HOOD/TRUNK

TRIGGER

DISARM

UNLOCK

SILENT ARM

SILENT DIS

ARM

PANIC MODE

All Icons Flash

OPERATING INSTRUCTIONS -ALARM

Disarming While Tripped (Triggered):

Disarming the System while it is triggering requires TWO presses of the #2 Unlock Button. The first press of

Button #2 Resets the alarm cycle only (system still armed) while a second press will disarm/unlock the system.

Selective Silent Arming/Disarming:

To Arm or Disarm the system without siren chirps, press and

release both Buttons #2 (Unlock) and #4 (Start) at the same time.

System will Arm or Disarm without siren chirps. Flashing lights and

LED will be the only indicators of Arm/Disarm status. The LCD will

Display a musical note with an “X” when the system is armed or

disarmed without a chirp

Prior intrusion Alert

This system will notify you if the alarm was triggered while you where away. Upon disarming, there will be four

additional siren chirps after the two normal disarm chirps. Check your vehicle for any signs of a break in or

tampering. Also,see LED Diagnostics Section to determine the cause of the trigger.

Remote Panic Protection

To sound the alarm in an emergency situation or to draw attention to your vehicle, press

and hold Button #1 (Lock) for at least 3 seconds until the siren sounds. Press Button #2

(Unlock) to reset panic mode. The LCD display will flash all the icons and emit 15 beeps

when the panic mode is triggered.

Selective Shock Sensor Disable

To arm the alarm and bypass shock sensor protection, press Button #1 as normal then

press and release Button #1 and #2 together within 2 seconds. You will hear 3 extra

siren chirps indicating shock sensor bypass for this arming cycle only. This feature useful

when parking near railroad tracks, airports, or area with excessive loud machinery or

noise to prevent the nuisance of unnecessary false alarms.

Open Door Alert / Bypass

Upon arming, this system will warn you if a door is left open. The LCD pager will vibrate and beep (15X’s)

along with displaying the open zone on your LCD screen. This zone will automatically be bypassed until

closed;otherwise,the alarm will continue to protect all other zones.

PRE-WARN

TRUNK POP

OPERATING INSTRUCTIONS -ALARM

Pre-Warning Shock Protection

The Pre-warning (warn-away) feature will activate when a low-level shock or vibration

detected by the system’s shock sensor. The alarm will chirp the siren 5 times and flash

the lights once to help deter any further tampering with the vehicle. The pager/remote

will vibrate and beep (1).

Passive Arming Mode: (Programmable)

Passive (automatic) arming occurs 30 seconds after the ignition is turned off and the last

door is closed. Upon closing the last door, the unit will flash the lights twice and LED will

be flashing rapidly to confirm passive countdown. If a door is reopened within the 30-

second period, the countdown stops and begins again when the door is closed. Passive

arming provides failsafe protection in case you forget to arm the system.

Passive Locking: (Programmable)

The CS2014FM system can be programmed to passively lock the doors when the system passively arms.

The default setting is OFF because passive locking increases the risk of locking the keys in the vehicle. When

the system arms/locks passively, without you pressing the remote.

Trunk/Hatch Pop (Optional, Remote AUX. Output 1)

This feature is designed to interface with existing Factory power trunk or power hatch

release systems and may require additional parts and/or labor charges. Press and

release Button #3 (Trunk) on the transmitter to pop/open the trunk/hatch. If the system is

armed, it will also disarm whenbutton #3 is pressed (programmable).

Remote AUX. Output 2 (Optional, Requires special programming)

This system contains a second auxiliary output to activate other accessories or devices.

To activate the second Auxiliary Output:Press and Hold Button #3 (Trunk Symbol) on

the transmitter for more than 2 seconds. This momentary output will stay active as long

as the remote button is held down. There is no LCD/pager confirmation for Aux. 2 output.

Dome Light Illumination (Optional)

This feature will turn on the vehicle’s dome light upon disarming for 30 seconds or until the key is inserted and

turned on. This will provide illuminated entry to your vehicle in dimly lit areas for safety and security.

VALET MODE

VALET PARK

OPERATING INSTRUCTIONS -ALARM

Emergency Override (Disarm)

If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to

disarm the system manually. Open the door with the key [alarm will sound], turn the ignition on, and press the

override/program button for about 5 seconds. The Alarm will disarm and allow you to use the vehicle until you

can repair/replace the remote. Valet mode also prevents Passive Arming.

Valet Mode (Enter manually or using the remote)

To disable Alarm and Remote Engine Starting for vehicle servicing or otherwise, turn the ignition on and press

the override/program button [about 5-7 seconds] until you hear (3) siren chirps and the LED turns on solid.

Repeat the process to exit VALET mode. To enter / exit valet via the remote, press and hold both buttons #1

(Lock) and Button #2 (unlock) together for about 3 seconds until 3 chirps are heard. Repeat this step to exit

via the remote transmitter. Lock/Unlock and AUX features will still operate in when in VALET mode however,

remote start and alarm functions are inhibited.

Valet Park Mode (Using the remote transmitter only)

Note: Valet Park mode isonly accessible when using the remote

transmitter. Valet park mode allows you to turn over the vehicle

to a valet allowing access to drive/lock/unlock your vehicle, but

alarm will trigger if the trunk is opened. To activate Valet Park,

press and hold both buttons #1 (Lock) and Button #2 (unlock)

together for about 6 seconds. 3 chirps will be heard first when

unit goes into regular Valet and as you continue to hold both

buttons you will hear 2 more chirps. LED will always flash

slowly when in Valet Park even when the Ignition is turned on

(or driving vehicle). Repeat step above to exit Valet Park mode.

Optional M.A.P. (Mobile Accessories Protection)

This system can be programmed to provide Crimestopper’s unique M.A.P. (Mobile Accessories Protection) feature that

allows you to prevent unauthorized access of your vehicles Audio, Cellular, Navigation, or Entertainment systems. This

feature is OPTIONAL and requires extra parts and labor for installation. Consult your installation dealer about MAP

before or during installation. The CS2016FM must be programmed for MAP operation. When the system is put into

Valet Park mode, M.A.P. will prevent stereo, entertainment, navigation, or cellular system from being used.

REMOTE ENGINE CONTROL

REMOTE ENGINE STARTING -SUCCESSFUL START

1) Press remote start button on the remote transmitter. System will chirp 3 times for audible confirmation.

(Chirps can be programmed on or off-See installation manual.)

2) Parking lights flash once, then turn on solid, Ignition/Accessory circuits turn on.

3) After a few seconds, Starter Motor engages, Parking lights and Accessory circuits turn off while cranking.

4) Engine Starts and Runs. Parking Lights and Accessory turn back on, Doors Lock.

5) Engine will remain running for programmed run time until reset with Brake pedal. If needed, the engine can

be turned off with remote transmitter.

REMOTE ENGINE STARTING -SUCCESSFUL START DIAGRAM:

REMOTE ENGINE STARTING –LCD PAGER-REMOTE:

When requesting a remote start the LCD pager remote will confirm

with an Ignition Icon along with 3beeps. Once the vehicle has

successfully started the remote will confirm back with 1vibration, a

moving vehicle Icon, and6beeps.

AFTER

IGN

STARTER

THEN

FLASH 1X

SOLID

SEC.

START

REMOTE START

(Key flashes)

REMOTE ENGINE CONTROL

UNSUCCESSFUL REMOTE START

In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then

attempts to restart the engine a 2nd and 3rd time. For hard starting engines, the unit will allow a starter crank

time of up to13 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to

13 seconds to help prevent damage to the starter from over cranking.

1) If engine starts on 2nd or 3rd attempt, see steps 4 & 5 (on last page) under "Successful Start".

2) If Third attempt fails to start engine, the system will turn off and doors will remain locked. NO FURTHER

ATTEMPTS WILL BE MADE AUTOMATICALLY UNLESS YOU PRESS THE REMOTE START BUTTON

AGAIN.

TURNING OFF YOUR REMOTE STARTED ENGINE (VIA REMOTE CONTROL):

1) Engine is running in Remote Start (Parking lights ON).

2) Press Remote Start button on remote transmitter.

3) Engine & parking lights turn OFF, Doors remain locked or will re-lock if applicable.

ENGINE & LIGHTS OFF

START

ENTERING YOUR REMOTE STARTED VEHICLE:

1) With engine running, Remote Unlock/Disarm system (If armed) or open door with key.

2) Enter vehicle and be careful not to step on brake pedal! (Remote Start Reset)

3) Turn Ignition to ON/RUN position, then press brake pedal to reset the Remote Starter & Shift out of park.

4) Remote starter will reset instantly when the brake is pressed. Parking lights will turn off and the ignition key

is now controlling your vehicle.

Inhaltsverzeichnis

Andere CrimeStopper Autoalarmanlage Handbücher

CrimeStopper

CrimeStopper CS-2015.FM.RevB Bedienungsanleitung

CrimeStopper

CrimeStopper SP-100 Bedienungsanleitung

CrimeStopper

CrimeStopper SecurLinc CS-2008PC Handbuch

CrimeStopper

CrimeStopper SP-200 Bedienungsanleitung

CrimeStopper

CrimeStopper SP-500 Systemhandbuch

CrimeStopper

CrimeStopper CS-9711 Systemhandbuch

CrimeStopper

CrimeStopper CS-2205 Handbuch

CrimeStopper

CrimeStopper SP-402 Bedienungsanleitung

CrimeStopper

CrimeStopper Traknet TN-4011 Stücklistenhandbuch

CrimeStopper

CrimeStopper CS-2100 Handbuch

CrimeStopper

CrimeStopper CG-1100 Bedienungsanleitung

CrimeStopper

CrimeStopper Traknet TN-4008 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-883 OEM Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2000 Handbuch

CrimeStopper

CrimeStopper CS-9602PI Betriebsanleitung

CrimeStopper

CrimeStopper The Informer II CS-2016FM Bedienungsanleitung

CrimeStopper

CrimeStopper OnGuard CS-2200WST Bedienungsanleitung

CrimeStopper

CrimeStopper SuperPage III CS-2006FM Montageanleitung

CrimeStopper

CrimeStopper CS-8716 Handbuch

CrimeStopper

CrimeStopper Super Rage CS-2012DPII-TW1 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2002 Bedienungsanleitung

CrimeStopper

CrimeStopper Super Rage CS-2011DP Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2011RS Series III Super Rage Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2007 Systemhandbuch

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung