Dynojet Power commander V Bedienungsanleitung

08-10 Kawasaki ZX10R PCV - 117-004 www.powercommander.com

2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com

2008-2010KawasakiZX10R

InstallationInstructions

PartsList

1 Power Commander

1 USB Cable

1 CD-ROM

1 Installation Guide

2 Power Commander Decals

2 Dynojet Decals

2 Velcro® Strip

1 Alcohol Swab

YOU CAN ALSO DOWNLOAD THE

POWER COMMANDER SOFTWARE AND

LATEST MAPS FROM OUR WEB SITE AT:

WWW.POWERCOMMANDER.COM

PLEASEREADALLDIRECTIONSBEFORESTARTINGINSTALLATION

TheignitionMUSTbeturned

OFFbeforeinstallation!

08-10 Kawasaki ZX10R PCV - 217-004 www.powercommander.com

Map- The PCV has the ability to hold 2 different base

maps. You can switch on the fly between these

two base maps when you hook up a switch to

the MAP inputs. You can use any open/close

type switch. The polarity of the wires is not

important. When using the Autotune kit one

position will hold a base map and the other

position will let you activate the learning mode.

When the switch is “CLOSED” Autotune will be

activated.

Shifter- These inputs are for use with the Dynojet

quickshifter. Insert the wires from the Dynojet

quickshifter into the SHIFTER inputs. The

polarity of the wires is not important.

Speed- If your application has a speed sensor then you

can tap into the signal side of the sensor and

run a wire into this input. This will allow you to

calculate gear position in the Control Center

Software. Once gear position is setup you can

alter your map based on gear position and

setup gear dependent kill times when using a

quickshifter.

Analog- This input is for a 0-5v signal such as engine

temp, boost, etc. Once this input is established

you can alter your fuel curve based on this input

in the control center software.

Crank- Do NOT connect anything to this port unless

instructed to do so by Dynojet. It is used to

transfer crank trigger data from one module to

another.

SHIFTER

SHIFTER

CRANK

MAP

ANALOG

SPEED

EXPANSIONPORTS1&2

Optional Accessories such as

Color LCD unit or Auto tune kit.

USBCONNECTION

Wireconnections:

To input wires into the PCV first remove the

rubber plug on the backside of the unit and

loosen the screw for the corresponding input.

Using a 22-24 gauge wire strip about 10mm

from its end. Push the wire into the hole of

the PCV until is stops and then tighten the

screw. Make sure to reinstall the rubber plug.

NOTE: If you tin the wires with solder it will

make inserting them easier.

ACCESSORYINPUTS

POWERCOMMANDERV

INPUTACCESSORYGUIDE

08-10 Kawasaki ZX10R PCV - 317-004 www.powercommander.com

FIG. A

FIG. C

FIG. B

6 Unplug the main wiring harness from the throttle bodies (Fig. C).

This is a 16 pin BROWN connector located under the fuel tank on the

right hand side of the bike

1. Remove the main seat and the passenger seat

2 Remove the covers for each side of the fuel tank (Fig. A).

3 Prop the front of the fuel tank up.

4 Slide the junction box that is under the main seat from it’s rubber sleeve.

This allows room for the PCV harness

5 Route the PCV harness underneath the subframe crossover (Fig. B).

Removecover

PCVharness

Unplug

08-10 Kawasaki ZX10R PCV - 417-004 www.powercommander.com

FIG. D

FIG. E

PCVharness

7 Plug the PCV connectors in-line of the stock wiring harness and throttle

body harness (Fig. D).

8 Attach the ground wire of the PCV to the stock wiring harness chassis

ground (Fig. E).

This connection is next to the PCV connection and starter relay.

9 Install the PCV in the tail section as shown in Figure F.

Speed input - BLUE/YELLOW wire. Sensor is located on the left hand side of

the engine case in front of the c/s sprocket.

Temperature input- Light ORANGE wire on 10 pin GREY connector under

fuel tank.

12v source for Autotune - RED wire of tail light connector.

FIG. F

Andere Handbücher für Power commander V

Andere Dynojet Autozubehör Handbücher

Dynojet

Dynojet power commander III Bedienungsanleitung

Dynojet

Dynojet Power commander V Bedienungsanleitung

Dynojet

Dynojet Power commander V Bedienungsanleitung

Dynojet

Dynojet Power commander V Bedienungsanleitung

Dynojet

Dynojet POWER VISION PV3-17-02 Bedienungsanleitung

Dynojet

Dynojet POWER VISION PV3-25-09 Bedienungsanleitung

Dynojet

Dynojet Power commander V Bedienungsanleitung

Dynojet

Dynojet Power Commander FC Bedienungsanleitung

Dynojet

Dynojet power commander III Bedienungsanleitung

Dynojet

Dynojet Power commander V Bedienungsanleitung

Dynojet

Dynojet Power Commander III USB Bedienungsanleitung

Dynojet

Dynojet Power commander V Bedienungsanleitung

Dynojet

Dynojet POWER VISION PV3-2511C Bedienungsanleitung

Dynojet

Dynojet Power commander V Bedienungsanleitung

Dynojet

Dynojet Power commander V Bedienungsanleitung

Dynojet

Dynojet WIDEBAND CX Bedienungsanleitung

Dynojet

Dynojet Power Vision Bedienungsanleitung

Dynojet

Dynojet Power Vision Bedienungsanleitung

Dynojet

Dynojet Power commander V Bedienungsanleitung

Dynojet

Dynojet Power commander V Service-Handbuch

Dynojet

Dynojet Power commander V Bedienungsanleitung

Dynojet

Dynojet Power commander V Bedienungsanleitung

Dynojet

Dynojet Power commander V Kurzanleitung

Dynojet

Dynojet INVISION INV-1901 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung