Federal Signal Corporation CAMSET56-AHD-NTSC2 Bedienungsanleitung

25500793

Rev A0 0622

Printed in U.S.A.

Installation and Operation Manual

Mobile Camera Systems

Limited Warranty

This product is subject to and covered by a limited warranty,

a copy of which can be found at www.fedsig.com/SSG-Warranty.

A copy of this limited warranty can also be obtained by written

request to Federal Signal Corporation, 2645 Federal Signal Drive,

University Park, IL 60484, email to [email protected] or

call +1 708-534-3400.

This limited warranty is in lieu of all other warranties, express or

implied, contractual or statutory, including, but not limited to the

warranty of merchantability, warranty of tness for a particular

purpose and any warranty against failure of its essential purpose.

2645 Federal Signal Drive

University Park, Illinois 60484

www.fedsig.com

Customer Support

Police/Fire-EMS: 800-264-3578 • +1 708 534-3400

Work Truck: 800-824-0254 • +1 708 534-3400

Technical Support 800-433-9132 • +1 708 534-3400

All product names or trademarks are properties of their respective owners.

Installation and Operation Manual

Federal Signal www.fedsig.com

Contents

Safety Messages ...................................................................................................... 4

An Overview of the Mobile Camera Systems......................................................... 6

Installing the Mobile Camera System..................................................................... 9

Connecting the Mobile Camera System............................................................... 26

Operating the Mobile Camera System.................................................................. 32

Getting Technical Support and Service................................................................ 38

Product Specications and Part Numbers........................................................... 39

Figures

Figure 1 Rear-view camera installation............................................................... 11

Figure 2 Side-view camera installation ............................................................... 15

Figure 3 Ball camera installation ......................................................................... 20

Figure 4 CAMLCD-BRACKET mounting bracket and hardware........................ 24

Figure 5 CAMBRK-HD mounting bracket and hardware.................................... 25

Figure 6 System congured with a CAMLCD-AHD-56 monitor......................... 28

Figure 7 System congured with a CAMLCD-AHD-70 monitor ........................ 30

Figure 8 CAMLCD-AHD-56.................................................................................... 33

Figure 9 CAMLCD-AHD-70.................................................................................... 35

Tables

Table 1 Rear-View Camera.....................................................................................39

Table 2 Side-View Camera .....................................................................................40

Table 3 Ball Camera................................................................................................41

Table 4 5.6-inch monitor w/ dual integrated camera inputs ...............................42

Table 5 7.0-inch monitor w/ four integrated camera inputs................................43

Safety Messages

Mobile Camera System

Federal Signal www.fedsig.com

Safety Messages

Safety Messages to Installers of Federal Signal Mobile

Camera Systems

People’s lives depend on your proper installation of our

products. It is important to read and follow all instructions

shipped with this product. Listed below are some other

important safety instructions and precautions you should

follow:

• To properly install a vehicular camera system, you must

have a good understanding of automotive electrical

systems along with proﬁciency in the installation and use

of safety warning equipment.

• The mobile camera system is only a supplement to the

rear-view/side-view mirrors of the vehicle. The system

is not a substitute for the proper use of the rear-view/

side-view mirrors of the vehicle. Always use caution when

backing up.

• DO NOT install equipment or route wiring in the

deployment path of an airbag.

• When drilling into a vehicle structure, ensure that both

sides of the surface are clear of anything that could be

damaged.

• Locate the camera(s) so the VEHICLE and SYSTEM can be

operated safely under all driving conditions.

• Frequently inspect the camera system to ensure that it is

operating properly and is securely attached to the vehicle.

The front face of any installed cameras should be kept

clean and free from any accumulated dirt or grime so that

the cameras may provide the clearest image. Obstructions

to the camera image limit the eectiveness of the system.

Safety Messages

Installation and Operation Manual

Federal Signal www.fedsig.com

• If a vehicle seat is temporarily removed, verify with the

vehicle manufacturer if the seat needs to be recalibrated

for proper airbag deployment.

• Do not open or service the camera element. There are no

user-serviceable parts inside. Opening or servicing any

component will void the component’s warranty.

• File these instructions in a safe place and refer to them

when maintaining and/or reinstalling the product.

Failure to follow all safety precautions and instructions may

result in property damage, serious injury, or death to you or

others.

An Overview of the Mobile Camera Systems

Mobile Camera System

Federal Signal www.fedsig.com

An Overview of the Mobile Camera Systems

Federal Signal Mobile Camera Systems provide drivers of

vehicles used in towing and recovery, ﬁre/EMS, utilities,

highway maintenance/DOT, sanitation, construction, and

many other industries an extended ﬁeld of view when

backing up or maneuvering their vehicles in environments

where optimum visibility is important for enhanced safety.

Designed exclusively for professional applications, all Federal

Signal systems and components are built with the distinct

needs of the commercial/industrial market in mind and are

backed by our two-year warranty.

Turnkey Systems

The following turnkey mobile camera systems are available:

CAMSET56-AHD-NTSC2

CAMSET70-AHD-NTSC4

Each system includes a monitor, a standard rear-view camera,

a camera-to-monitor extension cable, and accessories.

Components and systems that are NTSC-compatible

include “NTSC” in the part number, and those that are PAL-

compatible include “PAL” in the part number. The NTSC

video standard is primarily a North American video standard,

whereas the PAL video standard is predominantly a European

video standard.

CAMSET56-AHD-NTSC2

This system includes:

• a 5.6-inch color AHD LCD monitor (CAMLCD-AHD-56)

• a high-resolution rear-view camera with infrared low-

light vision capability and a microphone, with a mounting

hardware kit (CAMAHD-REARNTSC)

• a 65.5 ft (20 m) camera-to-monitor extension cable

(CAMCABLE-20)

An Overview of the Mobile Camera Systems

Installation and Operation Manual

Federal Signal www.fedsig.com

• an input/power/trigger wiring harness with inputs and

independent triggers for two cameras (CAMADP-INT-2)

• a monitor mounting bracket with mounting hardware

(CAMBRK-HD)

Features:

• Support for one or two cameras—an optional

additional camera can connect to the CAM2

connector on the input/power/trigger wiring harness

• Automatic triggering of either of two connected

cameras via individual camera trigger wires

• Individual camera settings that are conﬁgurable for

normal view or mirror-image view

• Easy setup with a minimum of connections

• Intuitive controls on the monitor for adjusting the

picture quality of the image and the volume of the

built-in microphone of the connected camera (as

applicable)

• CAMAHD-REARNTSC is IP68-rated for challenging

commercial applications that require a waterproof and

dustproof camera

CAMSET70-AHD-NTSC4

This system includes:

• a 7.0-inch color TFT LCD monitor

(CAMLCD-AHD-70)

• a high-resolution rear-view camera with infrared low-

light vision capability and a microphone, with a mounting

hardware kit (CAMAHD-REARNTSC)

• a 65.5 ft (20 m) camera-to-monitor extension cable

(CAMCABLE-20)

An Overview of the Mobile Camera Systems

Mobile Camera System

Federal Signal www.fedsig.com

• a four individual trigger wires for each of the available

camera inputs

• Input/power/trigger wiring harness with inputs and

independent triggers for four cameras (CAMADP-INT-4)

• Monitor mounting bracket with mounting hardware

(CAMBRK-HD)

Features:

• Support for one to four cameras—optional additional

cameras can connect to one of the available inputs

• Automatic triggering of any of up to four connected

cameras via individual camera trigger wires

• Individual camera settings that are conﬁgurable for

normal view or mirror-image view

• Easy setup with a minimum of connections

• Split-screen viewing of multiple connected cameras

• Intuitive controls on the monitor for adjusting the

picture quality of the image and volume of the built-in

microphone of the connected camera (as applicable)

• CAMAHD-REARNTSC is IP68-rated for challenging

commercial applications that require a waterproof and

dustproof camera

Monitors

• 5.6-inch monitor (CAMLCD-AHD-56): up to two cameras

can be connected

• 7.0-inch monitor (CAMLCD-AHD-70): up to four cameras

can be connected (split-screen viewing enabled)

Cameras

• Standard rear-view camera (CAMAHD-REARNTSC)

• Flush-mount camera (CAMCCD-FLSHNTSC)

• Side-view camera (CAMAHD-SIDENTSC)

Installing the Mobile Camera System

Installation and Operation Manual

Federal Signal www.fedsig.com

• Ball camera (CAMAHD-BALLNTSC)

Camera-to-monitor extension cables (one per camera)

• 4 inches (0.1 m) (CAMCABLE-SHORT)

• 16.5 feet (5 m) (CAMCABLE-5)

• 33 feet (10 m) (CAMCABLE-10)

• 49 feet (15 m) (CAMCABLE-15)

• 65.5 feet (20 m) (CAMCABLE-20)

• 131 feet (40 m) (CAMCABLE-40)

Installing the Mobile Camera System

After unpacking the system components, examine them for

damage that may have occurred in transit. If a component

has been damaged, do not attempt to install or operate it.

File a claim immediately with the carrier stating the extent of

the damage. Carefully check all envelopes, shipping labels,

and tags before removing or destroying them. Ensure that the

parts listed in the packing list are contained in the packing

carton.

Installing the Rear-View Camera (CAMAHD-REARNTSC)

Before the installation, ﬁnd an appropriate location for the

rear-view camera with these considerations in mind:

• Although the camera is waterproof, repeatedly exposing

it to direct, high-pressure streams of water (as from a

pressure washer) is not recommended.

• The material properties and thicknesses of vehicle bodies

vary widely. The included hardware can accommodate

many dierent vehicle installations. However, exercise

judgment when drilling holes into vehicle surfaces.

• When drilling into a vehicle structure, ensure that both

sides of the surface are clear of anything that could be

damaged. Remove all burrs from drilled holes. To prevent

Installing the Mobile Camera System

Mobile Camera System

Federal Signal www.fedsig.com

electrical shorts, grommet all drilled holes through which

wiring passes. (All Federal Signal camera systems include

grommets.) Ensure that the mounting screws do not cause

electrical or mechanical damage to the vehicle.

• This camera is recommended for rear-view applications in

heavy-duty vehicles. In most installations, the trigger wire

of this camera would be connected to the reverse lights

of the vehicle for automatic viewing when the vehicle is

operating in reverse. The camera is also equipped with

night vision and audio capability.

• If the camera is to be used in a typical backup camera

application, the camera should be positioned so that

the driver can obtain a wide, unobstructed ﬁeld of vision

behind the vehicle.

Preparing to install the Rear-View Camera

To prepare to install the camera:

1. Open the camera mounting hardware kit, which has:

• four self-tapping screws

• four machine screws with matching lock washers, ﬂat

washers, and nuts

• four plastic screw insulators

• an insulating pad

• an Allen®wrench

• waterprooﬁng tape

2. Use the Allen wrench to remove the sun shield and

camera from the mounting bracket so that the bracket

can be used as a template for marking drill-hole locations.

See Figure 1.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Federal Signal Corporation Autozubehör Handbücher

Federal Signal Corporation

Federal Signal Corporation Cuda TriOptic SIGNALMASTER 328823F Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation DFC-WC-FRD21 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Commander 371LED-120B Handbuch

Federal Signal Corporation

Federal Signal Corporation ESB-CRG07 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Commander 371LED-120 Handbuch

Federal Signal Corporation

Federal Signal Corporation Vision SLR Betriebsanleitung

Federal Signal Corporation

Federal Signal Corporation 7000 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation VSLR1-IPX Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Vision SLR Original Betriebsanleitung

Federal Signal Corporation

Federal Signal Corporation XHK-SD Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Legend Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Vista Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Fireball FB2LED Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation DFC-WC-DUR21 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation RAYDIAN Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation CUDA TRIOPTIC 351011 Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation DFC Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation SIFMH Handbuch

Federal Signal Corporation

Federal Signal Corporation ML-PT Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation GHSCENE Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Cuda TriOptic 351014F Series Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation JetSolaris JLX Series Handbuch

Federal Signal Corporation

Federal Signal Corporation CommCenter D1 Series Kurzanleitung

Federal Signal Corporation

Federal Signal Corporation LEDTCL97 Kurzanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung