Front Runner TBRA020 Bedienungsanleitung
TBRA020_REV_A02 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
front runner
TBRA020
ENG
1
Thank you for purchasing Front Runner Under Rack Table Slides.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
Under-Rack Table Slides
TBRA020_REV_A02 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
2
TOOLS NEEDED
FIGURE 1.1
GET ORGANIZED
1
IN THE BOX
3
10
11
12
9
1
8
2
4
5
6
1 1 X Table Slide LH
2 1 X Table Slde RH
3 10 X M8 x 16 Hex Bolt
4 10 X M8 x 16 x 1.6SS Flat Washer
5 10 X M8 Nyloc Nut
6 10 X M8 Nut Cap
7 1 X Table Latch
8 1 X T-Slot Rubber
9 2 X M6 Nyloc Nut
10 2 X M6 x 12 x 1SS Flat Washer
11 2 X Uni Screw Cap
12 2 X M6 x 12 Button Head Bolt
5mm
13mm
7
TBRA020_REV_A02 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
3
FIT AND SECURE - REAR MOUNT2
2.1
2.2
2.3
Working underneath and from the rear
of the Rack, Slide two M8 x 16 Hex Bolts
(Item 3) into the second, third, fourth
and fifthSlats of the rack through the
machined slots as shown.
Loosely secure the Table Slides (Item 1
&2) to the Rack using the M8 x 16 Flat
Washers and M8 Nyloc Nuts(Items 4 &
5) as shown.
Depending on the Width of your Table,
space the two Table Slides 750mm or
550mm apartand tighten all the Nyloc
Nuts and place a M8 Nut Cap (Item 6)
over each Nyloc Nut.
With the Rack still in the upside down
position, cut the T-slot Rubber (Item 8)
to suit the width of your Rack and
insert it into the rear channel of the
first slat by pinching / squeezing the
sides of the rubber together and
pushing / rolling the Rubber into
channel as shown.
2nd
3rd
4th
5th
Rack shown in
upside down position
Rear Of Rack
750mm or 550mm
TBRA020_REV _A02 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
4
FIT AND SECURE - REAR MOUNT2
2.4
2.5
2.6
With the Rack in the upright position,
Insert a M8 NylocNuts (Item 5) dome
side facing down into the'U" channel of
the Rack. Slide the Nyloc Nuts down the
"U" channel to the center of the Rack.
Place the Latch (Item 7) onto the Rack,
lining up the mounting hole in the Latch
with the Nyloc Nut inserted in 2.4.
Secure the Latchin position using a M8
x 20 Button Head Bolt and a M8 Flat
Washer.
Once the Rack has been mounted to the
vehicle, open the Latch by pushing on
the Latch Release and slide the Table
into position. Check that the table has
no Forward / Backward movement
when the latch is closed. If it does
loosen the Nyloc Hex Nuts (Item 5) from
2.2 and adjust so that the table has no
movement in the slides when the latch
is closed.
A small pad lock can be used through
the hole in the Latch Release should
you wish to lock the table.
Push Up To Open
TBRA020_REV _A02 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
5
FIT AND SECURE3
3.1
3.2
3.3
Decide whether you would like your
Table (Item 1) to exit on the left or right
hand side of the vehicle. There are two
Table Widths (550mm & 750mm). The
Illustrations in Steps A, B, C show the
Brackets positioned for a 750mm Wide
Table.
Insert five M8 x 16 Hex Bolts (Item 3)
into each of the two Slats as indicated
through the machined slots as shown.
Loosely secure the Table Slides (Item 1
& 2) to the Rack using the M8 Nyloc
Nuts and M8 x 19 Flat Washers (Items 4
&5) supplied.
Space the Table Slides 250 mm in
from the edge of the Rack as shown.
The Table Slides are slotted left to
right to enable adjustment. Space
the two Table Slides 750mm or
550mm apart and tighten all the
Nyloc Nuts. Place a M8 Nut Cap
(Item 6) over each Nyloc Nut.
5MM
TBRA020_REV _A02 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
6
FIT AND SECURE2
3.4
3.5
3.6
With the Rack in the upright position
and working on the side of the rack that
the Table will exit, insert a M8 Nyloc Nut
(Item5)dome side down into the "U"
channel of the Rack through the gap
in the corner as shown. Slide the Nyloc
Nut down the "U"channel and center
the Nut between the two Table Slides.
Place the Latch (Item7)onto the Rack,
lining up the mounting holes in the
Latch with the Nyloc Nut inserted in
Step 3.4. Secure the Latch in position
using two M8 x 20 Button Head Bolts
andtwo M8 Flat Washers.
Once the Rack has been mounted to
thevehicle, open the Latch by pushing
on theLatch Release and slide the Table
intoposition. Check that the table has
noForward / Backward movement
when thelatch is closed. If it does
loosen the NylocHex Nuts (Item 5) from
Step 3B andadjust so that the table has
no movementin the slides when the
latch is closed.
A small padlock can be used through
the hole in the Latch Release should
you wish to lock the table.
Push Up To Open
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FINISH
3
Congratulations! You did it. Take a step back and admire your work!
TBRA020_REV _A02 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
7
Inhaltsverzeichnis
Andere Front Runner Autozubehör Handbücher
Front Runner
Front Runner Easy-Out Bedienungsanleitung
Front Runner
Front Runner SSDR003 Bedienungsanleitung
Front Runner
Front Runner LAMS001 Bedienungsanleitung
Front Runner
Front Runner Slimline II FATF005 Bedienungsanleitung
Front Runner
Front Runner Drawer 6 Box Large MKII SSWO008 Bedienungsanleitung
Front Runner
Front Runner KRRK001T Bedienungsanleitung
Front Runner
Front Runner SAFE010 Bedienungsanleitung
Front Runner
Front Runner BRONCO TBRA040 Bedienungsanleitung
Front Runner
Front Runner SSAM009 Bedienungsanleitung
Front Runner
Front Runner KSTF003T Bedienungsanleitung
Front Runner
Front Runner RRAC054 Bedienungsanleitung
Front Runner
Front Runner TRCA004 Bedienungsanleitung
Front Runner
Front Runner 200 Series Bedienungsanleitung
Front Runner
Front Runner LASS026 Bedienungsanleitung
Front Runner
Front Runner LAMS004 Bedienungsanleitung
Front Runner
Front Runner FAJL002 Bedienungsanleitung
Front Runner
Front Runner SLIMLINE II Bedienungsanleitung
Front Runner
Front Runner TRFD001 Bedienungsanleitung
Front Runner
Front Runner SSDS201 Bedienungsanleitung
Front Runner
Front Runner SHOW013 Bedienungsanleitung
