La Crosse Technology TX231TH Bedienungsanleitung

PROFESSIONAL WEATHER STATION

INSTRUCTION MANUAL

Page

1. Introduction……………………………………………………………..…..2

2. Inventory of contents…………………………………………..………….2

2.1 Feature of the base station………………………….…………………2

2.2 Feature of wind sensor…………………………………..……………..3

2.3 Feature of rain sensor……………………………………..……………2

3. Set up guide…………………………………………………………….……2

3.1 Battery install…………………………………………………..…….......2

3.2 Mounting……………………………………………………..……..…….4

4. LCD overview……………………………………………………….……….5

4.1 LCD overview………………………………………………….…………5

4.2 Weather forecast…………………………………………….…..………6

4.3 Weather forecast tendency indicator……………………………….....6

4.4 Storm warning indicator………………………………………..……….6

5. Program modes……………………………………..………………..……..7

5.1 Quick display mode………………………………………………..…….7

5.2 Setting mode…………………………………………….………….……7

5.3 History mode……………………………………….…………….……….7

5.4 Alarm mode…………………………………………………….…………8

5.5 Min/Max mode…………………………………………………………….9

6. Problems and interference with operation………………………..……9

7. Specification……………………………………………………. ………....10

This Operation Manual is part of this product and should be kept in a safe place for future

reference. It contains important notes on setup and operation.

1. Introduction

Thank you for purchasing this Professional Weather Center Designed for everyday use, the weather station

will prove to be an asset of great value for your personal use in the home or office. Please read this

instruction manual thoroughly to fully understand the correct operation of your weather station and benefit

from its unique features.

2. Inventory of contents

1) Base station

2) WH1 sensor including thermo-hygro sensor, rain sensor, wind sensor, radio controlled time receiver

3) Instruction manual

4) 2 adjustable hoops (to fix the mast to your desired location)

The received data is continuously updated to bring you the latest weather information on the base station’s

LCD. The outdoor thermo-hygro sensors is the main data communication unit since both the wind and rain

sensors are connected the thermo-hygro sensor for operating power and rely on it to communicate to the

base station. Weather and Radio controlled time data sent from the thermo-hygro sensor is transmitted by

wireless transmission at 433MHZ frequency.

Additional equipment

(not included)

1. 3 Fresh AA 1.5V LR6 Alkaline batteries.

2. 2 Fresh AA 1.5V LR6 Alkaline batteries.

2.1 Feature of the base station:

Indoor and outdoor temperature display in degrees Fahrenheit or Celsius (user selectable)

Indoor and outdoor relative humidity displays

Barometric pressure reading in inHg or hPa, absolute or relative (user selectable)

Detailed display of rainfall data in 1 hour, 24 hours, one week, one month and total since last reset. (user

selectable in mm or inch)

Wind speed in mph, km/h, m/s, knots or Beaufort (user selectable)

Wind chill temperature display

Dew point temperature display

Weather forecast display by weather icons (sunny, cloudy, rainy)

Weather forecast tendency arrow

Storm warning alarm

Display of extensive weather data, in all cases with programmable alarm functions for certain weather

conditions as well as records of all minimum and maximum values along with time and date of their

recordings

LED back light

WWVB radio controlled time and date with manual setting option

12 or 24 hour time display

Perpetual calendar

Time zone setting

Daylight saving time manual setting on/off (met latest DST activating time)

Wall hanging or free standing

Synchronized instant reception

2.2 Features of wind sensor

The wind sensor measures wind speed and sends the data to thermo-hygro sensor, which in turn transmits

the data to the base station.

2.3 Feature of rain sensor

The rain sensor measures the rainfall and sends the data to thermo-hygro sensor, which in turn transmits the

data to the base station. Operating power is taken from the thermo-hygro sensor by a cable connection

3. Set up Guide

3.1 Battery install

Setting up using batteries:

Note: To avoid operating problems, please take note of battery polarity before/when inserting any

Alkaline Batteries (permanent damaged could be introduced by inserting the battery in wrong

direction). Use good quality Alkaline Batteries and avoid rechargeable batteries.

1) Pull away the shower proof casing of the thermo-hygro sensor to reveal the two sockets (for the wind

sensor and rain sensor)

2) Connect the attached cables of wind and rain sensors to the corresponding sockets of the thermo-hygro

sensor by clicking them into place. Make sure that rain and wind sockets not swapped when plugging the

phone jacket.

3) Open the base station’s battery cover located at the back of the unit and insert 3 x AA, 1.5V Alkaline

batteries into the battery compartment and close the battery cover

4) Open the battery cover of the thermo-hygro sensor located below the two sockets and insert 2 x AA, 1.5V

Alkaline batteries and close the cover

Every time the thermo-hygro sensor is powered up (for example after a change of batteries), the LED

indicator will light up for 4 seconds. The sensor will transmit weather data within the first 24s, and then the

sensor will start radio controlled time reception. During the RCC time reception period (maximum 5 minutes),

no weather data will be transmitted. The LED indicator will be blinking 5 times once RCC signal were

received. The LED indicator will not light again after RCC reception is successful. Regular RF link will be

established once RCC reception routine is finished.

When the base station is powered up, a short beep will sound and all LCD segments will light up for about 3

seconds before it enters into learning mode to learn the sensors security code. After the learning mode the

base station will start the radio controlled time reception.

Note: DO NOT PRESS ANY KEY during the first 10 minutes learning period or before radio controlled time is

displayed. After both outdoor weather data and radio controlled time are displayed you can place your remote

sensor outdoors and set your time (if no RCC reception is possible). If there is no temperature reading in the

indoor station, make sure the units are within range of each other or repeat the battery installation procedure.

If a key is pressed before the weather station receives the temperature signal, you will need to follow the

battery installation procedure again. Please wait minimum 10seconds before re-insert the battery again

to make a proper reset for both transmitter and receiver..

Note : If a battery change on the transmitter side happened, the base station will be resynchronized to the

transmitter within the next 3 hours. If you want to shorten the receiving data time, the base station has to

re-install the battery so that it can have the new security code learnt right way, however the previous data in

base station will be lost.

Note for Radio Controlled Time WWVB:

The time and date display is based on the signal provided by the highly accurate government operated

atomic clock. WWVB signal reception is on every even hour even the reception is successful. If reception has

been successful, the received time and date will overwrite the manually set time and date.

Note:

LED Indicator

Sensor Sockets

Battery

Compartmen

Batter

cover

Thermo-hygro Sensor

When batteries require replacement for the base station, the low battery indicator will light up on the LCD.

Please participate in the preservation of the environment by properly disposing of all used-up batteries

and accumulators at designated disposal points. Never dispose of batteries in a fire as this may cause

explosion, risk of fire or leakage of dangerous chemicals and fumes

3.2 Mounting

1) Base station

With one foldable leg at the back of the unit, the base station can be placed onto any flat surface or wall

mounted at the desired location by the hanging holes also at the back of the unit. It is important to check that

the radio signal can be received before permanently mounting any of the units

2) Remote sensor

There are two mounting methods available for the transmitter.

To mount the transmitter to a pole, follow steps 1, 2, and 3. To mount the transmitter to a flat surface follow

steps 1, 2, and 4.

4. LCD overview

4.1LCD overview

The following illustration shows the full segments of the LCD for description purposes only and will not

appear like this during normal operation and use.

1.Time

2. Alarm on indicator

3. Day of week/ time zone

4. Date

5. Indoor temperature display

6. Indoor humidity display

7. Indoor temperature and humidity low alarm and

high alarm

8. Temperature display unit

9. General indoor alarm icon

10. MIN/MAX information

11. Wind chill and dew point temperature display

12. Outdoor temperature and humidity display

16. Weather forecast icon

17.Weather tendency indicator

18. Pressure unit (relative or absolute)

19. Pressure with 24 hour history graph

20. Pressure low alarm and high alarm

21. Pressure display unit (inHg or hPa)

22. Pressure alarm on indicator

23. Wind speed display unit (m/s, km/h, knots, chill

mph, bft)

24. Wind speed high alarm

25. Wind alarm on indicator

26. Rainfall display unit (mm/in)

27. Rainfall 1h, 24h,week, month or total hour

13. Outdoor temperature and humidity low alarm

and high alarm

14. Temperature display unit

15. General outdoor alarm icon

display

28. Rainfall alarm on indicator

29. Radio controlled time version WWVB

30. Radio controlled time icon

4.2 Weather forecasting

Sunny Partly Cloudy Cloudy Rainy

The four weather icons Sunny, partly Cloudy, Cloudy and Rainy represent the weather forecasting. For every

sudden or significant change in air pressure, the weather icons will update accordingly to represent the

change in weather.

4.3 Weather forecast tendency indicator

The weather tendency indicators arrow is located between the weather icons to show the air pressure

tendency and provide a forecast of the weather to be expected by the decreasing or increasing air pressure.

The rightward arrow means that the air pressure is increasing and the weather is expected to become better.

The leftward arrow means that the air pressure is decreasing and the weather is expected to become worse.

The change of weather forecast icon is in accord to the relationship between current relative pressure and

the pressure change since last three hours. If the weather is changing, weather tendency indicator (animated

arrows) will be flashing. And then the arrows will fix while weather conditions have become stably.

Examples of changing weather icons:

4.4 Storm warning indicator

The storm threshold can be set to suit the user’s requirement for storm forecasting from level 3-9 (default

level 3). When there is a fall over pressure threshold in 3 hours, the storm forecasting will be activated, the

clouds with rain icon and tendency arrows will flash for 3 hours indicating the storm warning feature has been

activated.

Notes to pressure sensitivity setting for weather forecasting:

The pressure threshold can be set to suit the user’s requirement for weather forecasting from level 2-4

(default level 3). The lower level pressure threshold setting, the higher sensitivity for weather forecasting. For

areas that experience frequent changes in air pressure requires a higher setting compared to an area where

the air pressure is stagnant.

5. Program Mode

The base station has five keys for easy operation: SET key, + key, ALARM key, HISTORY key and MIN/MAX

key. And there are five program modes available: Quick Display Mode, Setting Mode, Alarm Mode，History

Mode and Min/Max Mode.

The program mode can be exited at any time by either pressing the HISTORY key, or waiting for the

30-second time-out to take effect.

5.1 Quick Display Mode

- While in Normal Mode, press the SET key to enter the Quick Display Mode as follow:

1. Outdoor Temperature / Wind chill / Dew point (press the +key or MIN/MAX key shifts the display

between outdoor temperature, wind chill and dew point)

2. Absolute pressure / Relative pressure (press the +key or MIN/MAX key shifts the display between the

absolute pressure and relative pressure)

3. Wind speed / Gust speed (press the +key or MIN/MAX key shifts the display between the wind speed

and gust speed)

4. 1 hour/ 24 hour / week/ month / total rainfall quantity (press the +key or MIN/MAX key shifts the display

between the selectable rainfall quantities), while display the rainfall total quantity, pressing the SET key

for 2s will reset the rainfall total value to zero and the time recording to current time.

- Press the SET key to accept the change and advance to the next display mode. Continue to press the SET

key to toggle through the display mode until return to the normal Mode

5.2 Setting Modes

-Press the SET key for 3 second while in normal mode to enter the normal Setting mode

-Press the SET key to select the following setting in sequence :

1. Time Zone Setting

2. DST on/off

3. 12/24 hour format

4. Manual time setting (hours/minutes)

5. Calendar setting(year/month /date)

6. Temperature display unit degree Celsius or Fahrenheit

7. Air pressure display units in hPa or inHg

8. Relative pressure setting from 27.13inHg – 31.89inHg (default 29.93inHg)

9. Pressure threshold setting (default 3)

10. Storm threshold setting (default 5)

11. Wind speed and gust display units in km/h, mph, m/s, knots, bft

12. Rainfall display units in mm or inch

-In the setting modes, press +key or MIN/MAX key change or scrolls the value. Holding the +key or

MIN/MAX key for 3 second will increase/decrease digits in great steps.

-Press HISTORY key or key idle 30 second, the setting mode will return to Normal Mode

Note: Please set the units firstly before change units’ value. During change of units setting, units’ value will

change according to new units but it might cause resolution loss due to its internal calculation algorithm.

Note: “DST OFF” indicates that the feature is off and the internal real time clock will not change times

automatically. “DST ON” indicates that the feature is on and the internal real time clock will change times

according to the DST time schedule automatically. Some locations (Arizona and parts of Indiana) do not

follow Daylight Saving Time, and should select “DST OFF”.

5.3 History Modes

-While in Normal Mode, press the HISTORY key to enter the History Mode.

-In the History Mode, press the +key to select the record over the past 24hours at increments of -3 hours,

-6 hours, -9 hours, -12 hours, -15 hours, -18 hours, -21 hours, -24 hours

-Press the HISTORY key or key idle 30 second to return to Normal Mode

5.4 Alarm Modes

- While in Normal Mode press the ALARM key to enter the High Alarm Mode

- Press the ALARM key again to enter Low Alarm mode

Remark: after the initial pressing of ALARM key, the display will be refreshed to show current high, low alarm

values. Normal alarm value will be displayed only for those already activated, all other not activated

values will be displayed with “- - -“or “- -“instead.

- Press the ALARM key again to return the Normal Mode

- In the High Alarm Mode press the SET key to select the following alarm modes:

1. Time alarm (hour/minute)

2. Indoor humidity high alarm

3. Indoor temperature high alarm

4. Outdoor humidity high alarm

5. Outdoor temperature high alarm

6. Wind chill high alarm

7. Dew point high alarm

8. Pressure high alarm

9. Wind speed high alarm

10. Gust speed high alarm

11. 1Hour rain high alarm

12. 24 hour rain high alarm

- In the Low Alarm Mode press the SET key to select the following alarm modes:

1. Time alarm (hour/minute)

2. Indoor humidity low alarm

3. Indoor temperature low alarm

4. Outdoor humidity low alarm

5. Outdoor temperature low alarm

6. Wind chill low alarm

7. Dew point low alarm

8. Pressure low alarm

- In the alarm modes, Press +key or MIN/MAX key change or scrolls the alarm value. Hold the +key or

MIN/MAX key for 3 second to change the number in great step. Press the ALARM key to choose the

alarm on or off (if alarm is enabled, the speaker icon on the LCD will be turned on indicating the alarm

function has been enabled). Press the SET key to toggle through each alarm mode until it returns to the

normal display mode.

- Press HISTORY key or key idle 10 second at any time, the alarm mode will return to Normal Mode

Canceling the Temperature Alarm While Sounding

a. When a set weather alarm condition has been triggered, that particular alarm will sound for 120 second

and flash until the weather condition doesn’t meet the user set level. Press any key to mute the alarm, but the

triggered source will continue to flash until weather conditions have become more steady. This feature is

useful to avoid repeated triggering for the same alarm value.

b. The alarm will reactivate automatically once the value has fallen below the set value.

The outdoor weather alarm

When a set outdoor weather alarm has been triggered, it will flash on the LCD display and the general

outdoor alarm icon and high/low alarm icon will flash accordingly. For example, in outdoor temperature

display mode, when dew point high alarm is triggered DEW POINT icon will flash along with general outdoor

alarm icon and high alarm icon flashing, telling that the current alarm source is from dew point. This is easier

for you to tell the triggering source for current alarm.

5.5 Min/Max Mode

-While in Normal Mode, press the MIN/MAX key to enter the maximum mode,

-Press MIN/MAX key again to enter the minimum mode

-Press MIN/MAX key again to return the Normal Mode

-In the maximum reading Mode, press the +key to display the following maximum values together with

the time and date stamp when these values were recorded, if press SET key in the following individual

maximum value will be reset to current reading together with the current time and date.

1. Indoor humidity maximum

2. Indoor temperature maximum

3. Outdoor humidity maximum

4. Outdoor temperature maximum

5. Wind chill temperature maximum

6. Dew point temperature maximum

7. Pressure maximum

8. Wind speed maximum

9. Gust speed maximum

10. 1Hour rain maximum

11. 24 hour rain maximum

12. Week rainfall maximum

13. Month rainfall maximum

-In the minimum reading Mode, press the +key to display the following minimum values together with the

time and date at which these values were recorded, if press SET key in the following individual minimum

value will be reset to current reading together with the current time and date.

1. Indoor humidity minimum

2. Indoor temperature minimum

3. Outdoor humidity minimum

4. Outdoor temperature minimum

5. Wind chill temperature minimum

6. Dew point temperature minimum

7. Pressure minimum

- Press the HISTORY key or key idle 10 second, the Min/Max mode will return to Normal Mode

6. Problems and interference with operation

Problem & cause Remedy

Distance between transmitters and receiver

too long Reduce distance between transmitters and receiver to

receive signal

High shielding materials between the units

(thick walls, steel, concrete, isolating aluminum

foil and etc.)

Find a different location for sensors and/or receiver. See

also item ‘transmission range’ below

Interference from other sources (e.g. wireless

radio, headset, speaker, etc. operating on the

same frequency)

Find a different location for the sensors and/or base

station. Neighbors using electrical devices operation on

the same signal frequency can also cause interference

with reception

No reception after adding extension cables Find a new location for the sensors and/or base station.

Poor contrast LCD or no reception or low

batteries in sensors or receiver Change batteries

Temperature, humidity, or air pressure is

incorrect.

Check/replace batteries. Move away from sources of

heat/cold. Adjust relative air pressure to a value from a

reliable source (TV radio, etc.).

7. Specifications

Outdoor data

Transmission distance in open field : 600 feet

Frequency : 433.92MHz

Temperature range : -22℉to +149℉(show OFL if outside range)

Resolution : 0.1℉

Measuring range rel. humidity : 10%～99%

Rain volume display : 0 – 9999mm (show OFL if outside range)

Resolution : 0.1mm (if rain volume < 1000mm)

1mm(ifrainvolume>1000mm)

Wind speed : 0~100mph (show OFL if outside range)

Measuring interval thermo-hygro sensor : 48 sec

Waterprooflevel : IPX3

Indoor data

Measuring interval pressure / temperature : 48 sec

Indoor temperature range : 32℉to + 140℉(show OFL if outside range)

Resolution : 0.1℉

Measuring range rel. humidity : 10%～99%

Resolution : 1%

Measuring range air pressure : 300-1100hPa (8.85-32.5inHg)

Accuracy : +/-3hpa under 700-1100hPa

Resolution : 0.1hPa(0.01inHg)

Alarm duration : 120 sec

Power consumption

Base station : 3XAA 1.5V LR6 Alkaline batteries

Remotesensor : 2xAA1.5VLR6Alkalinebatteries

Batterylife : Minimum12monthsforbasestation

Minimum24monthsforthermo-hygrosensor

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Caution!

Any changes or modifications not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment.

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology WS9611 Bedienungsanleitung

La Crosse Technology

La Crosse Technology TX31U-IT Technisches Datenblatt

La Crosse Technology

La Crosse Technology WS-9035U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9632U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9006U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 328-1415 Installationsanleitung

La Crosse Technology

La Crosse Technology WS-7213U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8035U Bedienungsanleitung

La Crosse Technology

La Crosse Technology T83653v2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2310 Technisches Datenblatt

La Crosse Technology

La Crosse Technology WS6828 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2010 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-3512 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7025U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9400U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-145 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7034U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology M76171 Abmessungen

La Crosse Technology

La Crosse Technology S88785 Bedienungsanleitung

La Crosse Technology

La Crosse Technology DCF-77 Bedienungsanleitung

La Crosse Technology

La Crosse Technology V21v4 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7038U Bedienungsanleitung

La Crosse Technology

La Crosse Technology KCombo3 WS-9080U-IT WS-9640U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7078UF Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Renkforce

Renkforce 1208067 Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung