Metra Electronics 95-9313B Bedienungsanleitung

REV. 1/25/2017 INST95-9313B

Installation instructions for part 95-9313B

CAUTION!

All accessories, switches, climate controls panels,

and especially air bag indicator lights must be connected before

cycling the ignition. Also, do not remove the factory radio with

the key in the on position, or while the vehicle is running.

• ISO DDIN radio provision

• Painted matte black

• Relocates the factory climate control and switches

• Parts included to modify the factory airbox

• A) Radio trim panel • B) Back up housing • C) Radio brackets • D) Climate and switch panel housing

• E) Airbox cover • F) Cutting template • G) Climate bracket • H) Actuator arm • I) (1) #6 x 1/2” Phillips screw

• J) (4) #8 x 1/2” Phillips screws • K) (2) #8 x 3/8” Phillips screws • L) (2) panel clips • M) Vent door

KIT FEATURES

KIT COMPONENTS WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • 70-8590 • 70-9003 (nav models 02-06)

Antenna Adapter: • 40-VW10 40-EU10 (nav models 02-06)

• Panel removal tool • Phillips screwdriver • Pick tool

TOOLS REQUIRED

BMW 3-Series 1999-2005,

3-Series (coupe, convertible) 2006, M3 2001-2006

(for factory switch panel with one long opening)

95-9313B

G I JH

D E

K L M

Dash Disassembly ..............................................2-5

Sub-dash airbox modifications..........................6-9

Kit Assembly

–ISO DDIN radio provision.................................... 10

Climate and Switch Panel Assembly .................. 11

Table of Contents

95-9313B

Dash Disassembly

1. Unclip and remove the trim panel

above the glove box. (Figure A)

2. Unclip and remove the trim panel

above the factory radio. (Figure B)

3. Remove (2) Phillips screws

securing the radio and then unplug

and remove the radio. (Figure C)

Continued on the next page

(Figure A) (Figure C)(Figure B)

95-9313B

(Figure D)

4. Unsnap and remove the climate

control panel. (Figure D)

5. Pull straight up on the shift knob to

remove. (Figure E)

6. Unclip and remove the boot around

the shift selector. (Figure F)

Continued on the next page

Dash Disassembly

(Figure E) (Figure F)

95-9313B

Dash Disassembly

7. Remove (2) Phillips screws

securing the shift selector trim

panel, and then unclip and remove

the panel. (Figure G)

8. Open the upper door on the lower

switch panel. Using a pick tool, or

something suitable, disengage (2)

clips in the upper corners of the

tray to remove the tray and door.

(Figure H)

(Figure G) (Figure H)

95-9313B

9. Remove (4) Phillips screws now

exposed securing the lower switch

panel, and then unplug and remove

the panel. (Figure I)

Note: All of the switches

will need to be removed and

installed into the new switch

panel provided.

10. Remove (2) Phillips screws, and

then unclip and move aside the

vent assembly above the radio

opening. It is not necessary to

remove the assembly. But if

desired, there will be a cable

attached to the assembly that will

need to be removed. (Figure J)

11. For non-NAV equipped cars,

remove (2) Phillips screws

securing the plastic radio/climate

housing from the radio/climate

cavity, and then remove.

Continue to kit assembly

(Figure I) (Figure J)

Dash Disassembly

95-9313B

Sub-dash airbox modifications

1. Remove (4) metal retaining clips

holding the air box front panel in

place and remove the panel.

Note: One of the retaining clips

will be reused in step 7.

(Figure A)

2. Clip the cutting template over the

top edge of the air box, mark for

cutting, remove the template, then

and cut the marked area.

(Figure B)

Continued on the next page

(Figure A) (Figure B)

95-9313B

Sub-dash airbox modifications

3. Remove the upper actuator arm

from the passenger vent door.

Remove the lower actuator arm

from the vent doors. Unclip the

passenger side first and then the

drivers side. (Figure C)

4. Remove the passenger side vent

door. Unclip from the bottom, then

push and rotate the top clip out of

the slot in the airbox. (Figure D)

Note: Remember the orientation

of the vent door arm (approx.

11:00) when removing to ease in

reinstallation.

Continued on the next page

(Figure C) (Figure D)

95-9313B

Sub-dash airbox modifications

(Figure E) (Figure F)

5. Replace the factory passenger side

vent door with the supplied vent

door. Rotate the vent door into the

upper slot and clip into the lower

socket. (Figure E)

6. Replace the factory actuator

arm with the supplied actuator

arm. Clip the drivers side in first

and then the passenger side.

Reconnect the upper actuator arm

to the passenger vent door.

(Figure F)

Continued on the next page

95-9313B

Sub-dash airbox modifications

7. Set the air box cover into place

and secure the right side with the

metal retaining clip removed in

step 1. Secure the left side with

the (1) #6 x 1/2” Phillips screw

supplied. (Figure G)

8. Metra recommends using tape

along the upper edge of the air box

cover where the cut was made.

Duct tape or A/C aluminum tape is

suggested. (Figure H)

Continue to kit assembly

(Figure G) (Figure H)

Tape the shaded area

Clip

location

Screw

location

95-9313B

(Figure B)

(Figure C)(Figure A)

1. Attach the radio brackets to the

radio using the screws supplied

with the radio. (Figure A)

2. Attach the back-up housing to the

radio/bracket assembly with the (4)

#8 x 1/2” Phillips screws supplied.

(Figure B)

3. Locate the factory wiring harness

and antenna connector in the

dash, and complete all necessary

connections to the radio and

climate control panel. Metra

recommends using the proper

mating adapter from Metra and/or

AXXESS. Test the radio for proper

operation.

Note: After all testing has been

performed, disconnect the

climate control panel, relocate

the harness to the lower switch

panel area, and then proceed to

the next step.

Kit Assembly

4. Secure the completed assembly

into the radio/climate cavity using

the (2) #8 x 3/8 inch screws

supplied.

5. Secure the vent assembly to the

vehicle using the (2) factory Phillips

screws removed in step 10 of dash

disassembly.

6. Attach (2) panel clips provided

with the kit onto the radio trim

panel (Figure C), and then attach

the panel to the radio assembly.

Secure the assembly to the vehicle

using the (2) factory Phillips

screws removed in step 3 of dash

disassembly.

Continue to climate and switch

panel assembly

Inhaltsverzeichnis

Sprachen:

Andere Metra Electronics Autozubehör Handbücher

Metra Electronics

Metra Electronics 70-6504 Bedienungsanleitung

Metra Electronics

Metra Electronics 95-8210 Bedienungsanleitung

Metra Electronics

Metra Electronics 99-9224 Bedienungsanleitung

Metra Electronics

Metra Electronics 99-3014G Bedienungsanleitung

Metra Electronics

Metra Electronics 99-1005 Bedienungsanleitung

Metra Electronics

Metra Electronics 99-7604 Bedienungsanleitung

Metra Electronics

Metra Electronics 99-3304 Bedienungsanleitung

Metra Electronics

Metra Electronics DODGE 99-6540 Bedienungsanleitung

Metra Electronics

Metra Electronics 95-8904B Bedienungsanleitung

Metra Electronics

Metra Electronics 108-TO4 Bedienungsanleitung

Metra Electronics

Metra Electronics 95-7504 Bedienungsanleitung

Metra Electronics

Metra Electronics 99-7309 Bedienungsanleitung

Metra Electronics

Metra Electronics 99-3106 Bedienungsanleitung

Metra Electronics

Metra Electronics 98-8999 Bedienungsanleitung

Metra Electronics

Metra Electronics 99-7404 Bedienungsanleitung

Metra Electronics

Metra Electronics 99-5816 Bedienungsanleitung

Metra Electronics

Metra Electronics 95-7801 Bedienungsanleitung

Metra Electronics

Metra Electronics MAZDA CX7 2007-09 99-7508 Bedienungsanleitung

Metra Electronics

Metra Electronics XIAH-FD4 Bedienungsanleitung

Metra Electronics

Metra Electronics 108-GM2B Bedienungsanleitung

Metra Electronics

Metra Electronics GMRC-02 Bedienungsanleitung

Metra Electronics

Metra Electronics 99-5828CH Bedienungsanleitung

Metra Electronics

Metra Electronics 70-7306 Bedienungsanleitung

Metra Electronics

Metra Electronics 95-2009 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung