Moxa Technologies CSM-400 Series Bedienungsanleitung

P/N: 1802004002011

*1802004002011*

CSM-400 Series

Quick Installation Guide

Version 1.2, June 2021

Technical Support Contact Information

www.moxa.com/support



- 2 -

Overview

Introduction

The CSM-400 Series is an Ethernet to optical-fiber media converter and

is part of the NRack System. It provides Ethernet media conversion

from 10/100 BaseT(X)-to-100 BaseFX (SC or ST connectors), and it can

be installed in every chassis of the NRack System.

The CSM-400 Series includes the following models:

•CSM-400-1213: 10/100BaseT(X)-to-100BaseFX slide-in

management module converter, multimode ST connector

•CSM-400-1214: 10/100BaseT(X)-to-100BaseFX slide-in

management module converter, multimode SC connector

•CSM-400-1218: 10/100BaseT(X)-to-100BaseFX slide-in

management module converter, single-mode SC connector

•CSM-400-1224: 10/100BaseT(X)-to-100BaseFX slide-in

management module converter, WDM-A single-mode SC connector

•CSM-400-1225: 10/100BaseT(X)-to-100BaseFX slide-in

management module converter, WDM-B single-mode SC connector

Installation

The CSM-400 media converter slide-in module can be hot-swapped,

which means the chassis does not need to be powered off or removed

during installation. Align the slide-in module with the chassis

installation slot so that the panel fastener screw is at the top of the

module and carefully slide the slide-in module into the slot while

aligning the module’s circuit board with the installation guide.

Ensure that the slide-in module is firmly seated inside the chassis. Push

in and rotate the attached panel fastener screw clockwise to secure the

module to the chassis.

Why Convert Ethernet to Fiber?

Fiber communication not only extends the communication distance, but

also provides many advantageous features.

•IMMUNITY FROM ELECTRICAL INTERFERENCE:

Fiber is not affected by electromagnetic interference or radio

frequency interference. It provides a clean communication path and

is immune to cross-talk.

•INSULATION:

Optical fiber is an insulator; the glass fiber eliminates the need for

using electric currents as the communication medium.

•SECURITY:

Fiber cannot be tapped by conventional electric means and is very

difficult to tap into optically. Furthermore, radio and satellite

communication signals can be captured easily for decoding.

•RELIABILITY & MAINTENANCE:

Fiber is immune to adverse temperature and moisture conditions,

does not corrode or lose its signal, and is not affected by short

circuits, power surges, or static electricity.

- 3 -

Features

•LFP(Link Fault Pass-through)

•Supports store-and-forward and pass-through modes

•Auto negotiation for copper port

•Supports IEEE 802.3AH OAM protocol

•Plug and Play

•Hot-swap

•IP-based remote management

•Supports WDM type modules

NOTE

When you enable the LFP function of the CSM

-400 series of

media converter

s to use on the TRC-

2190, you must choose the

CSM

200/400 product for use at a remote site to make sure the

LFP function can successfully use this function.

Package Checklist

Moxa’s CSM-400 Series is shipped with the following items.

•CSM-400 Series

•Quick installation guide (printed)

•Warranty card

NOTE

Please notify your sales representative if any of the above

items are missing or damaged.

Dimensions

CSM-400-1213

- 4 -

CSM-400-1214/CSM-400-1218

CSM-400-1224/CSM-400-1225

Electrostatic Discharge Warning!

To protect the product from damage due to electrostatic

discharge, we recommend wearing a grounding device when

handling your CSM-400 slide-in modules.

Communication Connections

The CSM-400 Series has one 10/100BaseT(X) Ethernet port, and one

100BaseFX (SC or ST type connector) fiber port.

- 5 -

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) Ethernet ports located on CSM-400 are used to

connect to Ethernet-enabled devices.

Below, we show pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports, and also show cable-wiring diagrams for

straight-through and crossover Ethernet cables.

10/100BaseT(X) RJ45 Pinouts

MDI Port Pinouts MDI-X Port Pinouts 8-pin RJ45

Signal

Tx+

Tx-

Rx+

Rx-

Signal

Rx+

Rx-

Tx+

Tx-

RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring

RJ45 (8-pin) to RJ45 (8-pin) Crossover Cable Wiring

100BaseFX Fiber Port Connection

The concept behind the fiber port and cable is quite straightforward.

Suppose you are connecting devices I and II. Contrary to electrical

signals, optical signals do not require a circuit in order to transmit data.

Consequently, one of the optical lines is used to transmit data from

device I to device II, and the other optical line is used transmit data

from device II to device I, for full-duplex transmission.

All you need to remember is to connect the Tx (transmit) port of device

I to the Rx (receive) port of device II, and the Rx (receive) port of

device I to the Tx (transmit) port of device II.

If you are making your own cable, we suggest labeling the two sides of

the same line with the same letter (A-to-A and B-to-B, as shown below,

or A1-to-A2 and B1-to-B2).

- 6 -

SC-Port Pinouts

SC-Port to SC-Port Cable Wiring

ST-Port Pinouts

ST-Port to ST-Port Cable Wiring

ATTENTION

This is a Class 1 Laser/LED product. Do not stare into the Laser

Beam.

LED Indicators

There are two LEDs on the front bracket of the CSM-400 slide-in

modules.

LED

Color

State

Function

PWR Green

On Power is being supplied to power

input.

Off

Power is not being supplied to power

input.

Fault Red

LED is on and the CSM-400 is booting

up, or a power error condition exists

Blinking Indicates and IP conflict, or the DHCP

server did not respond properly

Off

LED is off and the CSM-400 is

functioning normally; a power error

condition does not exist

Fiber Link Green

FX port’s 100 Mbps is active.

Blinking Data is being transmitted at 100

Mbps.

Off

100BaseFX port is inactive.

10M (TP) Yellow

TP port’s 10 Mbps is active.

Blinking

Data is being transmitted at 10 Mbps.

Off

TP port’s 10 Mbps link is inactive.

100M (TP) Green

TP port’s 100 Mbps is active.

Blinking

Data is being transmitted at 100

Mbps.

Off

TP Port’s 100 Mbps is inactive.

- 7 -

Auto MDI/MDI-X Connection

The Auto MDI/MDI-X function allows users to connect the Moxa CSM-

400’s 10/100BaseTX ports to any kind of Ethernet device, without

needing to determine the type of Ethernet cable being used for the

connection.

This means that you can use either a straight-through cable or

crossover cable to connect the CSM-400 Series to Ethernet devices.

Dual Speed Functionality and Switching

The Moxa CSM-400’s 10/100 Mbps RJ45 Ethernet port auto negotiates

with the connected device for the fastest data transmission rate

supported by both devices. All models of the CSM-400 Series are plug-

and-play devices, so that software configuration is not required at

installation, or during maintenance. The half/full duplex mode for the

RJ45 Ethernet ports is user dependent and changes (by auto-

negotiation) to full or half duplex, depending on which transmission

speed is supported by the attached device.

Auto-Negotiation and Speed Sensing

All of the CSM-400’s RJ45 Ethernet ports independently support auto-

negotiation for 10BaseT and 100BaseTX transmission speeds, with

operation according to the IEEE 802.3u standard.

This means that some nodes could be operating at 10 Mbps, while at

the same time other nodes are operating at 100 Mbps.

Auto-negotiation takes place when an RJ45 cable connection is made,

and then each time a LINK is enabled. Moxa’s CSM-400 advertises its

capability for using either 10 Mbps or 100 Mbps transmission speeds,

with the device at the other end of the cable expected to advertise

similarly. Depending on what type of device is connected, this will

result in agreement to operate at a speed of either 10 Mbps or 100

Mbps.

If a Moxa CSM-400 RJ45 Ethernet port is connected to a non-

negotiating device, it will default to 10 Mbps speed and half-duplex

mode, as required by the IEEE 802.3u standard.

Specifications

Technology

Standards IEEE 802.3 for 10BaseT,

IEEE 802.3u for 100BaseT(X), 100BaseFX

Interface

RJ45 ports

10/100BaseT(X)

Fiber ports

100BaseFX (SC/ST connector)

LED Indicators

PWR, Fiber Link, 10/100M(TP port)

- 8 -

Optical Fiber

100BaseFX

Multi-mode

Single mode

Wavelength

1300 nm

1310 nm

Max. TX

-10 dBm

0 dBm

Min. TX

-20 dBm

-5 dBm

RX Sensitivity

-32 dBm

-34 dBm

Link Budget

12 dB

29 dB

Typical Distance

5 kma

4 km

40 kmc

Saturation

-6 dBm

-3 dBm

a. 50/125 μm, 800 MHz*km fiber optic cable

b. 62.5/125 μm, 500 MHz*km fiber optic cable

c. 9/125 μm, 3.5 PS/(nm*km) fiber optic cable

Physical Characteristics

Housing

SPCC

Dimensions

86.8 x 124.3 x 21 mm (3.42 x 4.89 x 0.83 in)

Weight Product only:

CSM-400-1213/1214/1218 : 115 g (0.25 lb)

CSM-400-1224/1225 : 125 g (0.28 lb)

Packaged:

CSM-400-1213/1214/1218 : 170 g (0.37 lb)

CSM-400-1224/1225 : 180 g (0.40 lb)

Environmental Limits

Operating

Temperature

Standard Models: -20 to 55°C (-4 to 131°F)

Wide Temp. Models: -40 to 75°C (-40 to 167°F)

Storage

Temperature

-40 to 85°C (-40 to 185°F)

Humidity

5 to 95 % RH

Power Requirements

Input Voltage

12 VDC

Power

Consumption

220 mA @ 12 VDC max.

Regulatory Approvals

Class A

FCC

Part 15 sub part B class A

EMS EN61000-4-2 (ESD), Criteria A, Level 4

EN61000-4-3 (RS), Criteria A, Level 2

EN61000-4-4 (EFT), Criteria A, Level 3

EN61000-4-5 (Surge), Criteria A, Level 3

EN61000-4-6 (CS), Criteria A, Level 2

En61000-4-8 (PFMF), Criteria A, Level 3

Freefall

IEC 60068-2-32

Warranty

Warranty Period

5 years

Details:

See www.moxa.com/warranty

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Medienkonverter Handbücher

Moxa Technologies

Moxa Technologies ICF-1150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCC-100 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1170I-M-ST Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 464 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5410 Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 251 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5110A Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21GA-T Handbuch

Moxa Technologies

Moxa Technologies TCF-142-S-ST-RM Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 451 Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCC-80I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort DE-311 Handbuch

Moxa Technologies

Moxa Technologies UPORT 1400 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-101 Series Handbuch

Moxa Technologies

Moxa Technologies IMC-101 Series Handbuch

Moxa Technologies

Moxa Technologies TCF-142-M-ST Bedienungsanleitung

Moxa Technologies

Moxa Technologies PTC-101-M12 Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-S Bedienungsanleitung

Moxa Technologies

Moxa Technologies ME60A Handbuch

Moxa Technologies

Moxa Technologies VPort 251 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5100A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort Z2150 Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-RM Series Handbuch

Moxa Technologies

Moxa Technologies NE-4100 Series Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung