Moxa Technologies IMC-101 Series Handbuch

Moxa Industrial Media Converter

IMC-101 Hardware Installation Guide

Fifth Edition, June 2008

Reproduction without permission is prohibited.

P/N: 18020010104

Overview

Moxa Industrial Media Converter, which is specially designed for reliable and

stable operation in harsh industrial environments, provides industrial grade

media conversion between 10/100BaseT(X) and 100BaseFX. IMC-101’s

reliable industrial design is excellent for keeping your industrial automation

applications running continuously, and comes with a relay output warning

alarm to help prevent damages and losses.

This product has a wide operating temperature range, from -40 to 75°C, and is

designed to withstand a high degree of vibration and shock. The rugged

hardware design makes IMC-101 perfect for ensuring that your Ethernet

equipment can withstand critical industrial applications, such as in hazardous

locations (Class 1 Division 2/Zone 2), and complies with FCC, TÜV, UL, and

CE Standards

NOTE Throughout this Hardware Installation Guide, we often use

IMC as an abbreviation for Moxa Industrial Media

Converter:

IMC = Moxa Industrial Media Converter

Package Checklist

Moxa Industrial Media Converter is shipped with the following items. If any of

these items is missing or damaged, please contact your customer service

representative for assistance.

yMoxa Industrial Media Converter

yHardware Installation Guide

yMoxa Product Warranty booklet

Features

ySupports 10/100Base-TX auto-negotiation and auto-MDI/MDI-X

yMulti mode, single mode with SC or ST fiber connector available

ySupports Link Fault Pass-Through

yRelay Output alarm when a port breaks or the power fails

yRedundant 12 to 48 VDC power inputs, DIN-Rail or panel mountable

yOperating temperature range from 0 to 60°C, or extended operating

temperature from –40 to 75°C for (-T) models

Panel Layout of IMC-101 Series

V1 V2 INPUTS: 24 VDC

PWR2

V2+

V2-

V1-

V1+

FAULT

PWR1

123

ON DIP

PORT ALARM

FDX /CO L

Top Panel View

Rear Panel View

Front Panel View (IMC-101-M-ST)

Front Panel View (IMC-101-M-SC)

1. Grounding screw

2. Terminal block for power

input PWR1/PWR2 and relay

output

3. Heat dissipation orifices

4. Dip switch

5. Power input PWR1 LED

6. Power input PWR2 LED

7. Fault LED

8. 100BaseFX (ST connector)

Port

9. FX port’s 100 Mbps LED

10. FX port’s Full

Duplex/Collision LED

11. TP port’s 100 Mbps LED

12. 10/100BaseT(X)

13. TP port’s 10 Mbps LED

14. Model Name

15. 100BaseFX (SC connector)

Port

16. Screw hole for wall mounting kit

17. DIN-Railmountingkit

Mounting Dimensions

Back View

Front ViewSide View

10.65 10.65

30.50

57.05

13.90

66.80

Panel Mount Kit

(Unit = mm)

135.00

13.10 15.10

25.40

13.90

18.20

25.71

23.15

7.75

30.50

7.75

3.5

39.37

46.77

135.00

30.00

9.50

54.00

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should be fixed to the back panel of

IMC when you take it out of the box. If you need to reattach the DIN-Rail

attachment plate to IMC, make sure the stiff metal spring is situated towards

the top, as shown in the figures below.

STEP 1:

Insert the top of the DIN-Rail into the

slot just below the stiff metal spring.

STEP 2:

The DIN-Rail attachment unit will

snap into place as shown below.

metal

spring

DIN-Rail

metal

spring

DIN-Rail

To remove Moxa Industrial Media Converter from the DIN-Rail, simply

reverse Steps 1 and 2 above.

Wall Mounting (Optional)

For some applications, you will find it convenient to mount Moxa Industrial

Media Converter on the wall, as illustrated below.

STEP 1:

Remove the aluminum DIN-Rail attachment plate from Moxa Industrial Media

Converter, and then attach the wall mount plates, as shown in the diagrams

below.

⇒

Top

plate

Bottom

plate

STEP 2:

Mounting Moxa Industrial Media Converter on the wall

requires 4 screws. Use the IMC, with wall mount plates

attached, as a guide to mark the correct locations of the 4

screws. The heads of the screws should be less than 6.0

mm in diameter, and the shafts should be less than 3.5

mm in diameter, as shown in the figure at the right.

NOTE Test the screw head and shank size by inserting

the screw into one of the keyhole shaped

apertures of the Wall Mounting Plates, before it

is screwed into the wall.

Do not screw the screws in all the way—leave a space of

about 2 mm to allow room for sliding the wall mount

panel between the wall and the screws.

6.0 mm

3.5 mm

STEP 3:

Once the screws are fixed in the wall, insert the four screw heads through the

large parts of the keyhole-shaped apertures, and then slide Moxa Industrial

Media Converter downwards, as indicated below. Tighten the four screws for

added stability.

Wiring Requirements

WARNING

Do not disconnect modules or wires unless power has been

switched off or the area is known to be non hazardous.

The devices may only be connected to the supply voltage shown

on the type plate.

The devices are designed for operation with a safety extra-low

voltage. Thus, they may only be connected to the supply voltage

connections and to the signal contact with the safety extra-low

voltages (SELV) in compliance with IEC950/ EN60950/

VDE0805.

WARNING

Substitution of components may impair suitability for Class I,

Division 2 and Zone 2.

These devices must be supplied by a SELV source as defined in

the Low Voltage Directive 73/23/EEC and 93/68/EEC.

WARNING

This equipment has been evaluated as EEx nC IIC T4

equipment under DEMKO Certificate No. 03 ATEX

0324537U. Each module is marked with II 3G and is

suitable for use in Zone 2 Explosive Atmospheres. Devices

must be installed in a minimum IP 54 enclosure as defined in

IEC 60529 and EN 60529.

ATTENTION

This unit is a built-in type. During installation into certain

end equipment, it must comply with fire enclosure

stipulations of IEC 60950/EN60950, or similar statements.

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa Industrial Media Converter.

ATTENTION

Safety First!

Calculate the maximum possible current in each power wire

and common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring

could overheat, causing serious damage to your equipment.

You should also pay attention to the following points:

yUse separate paths to route wiring for power and devices. If power wiring

and device wiring paths must cross, make sure the wires are perpendicular

at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring in

the same wire conduit. To avoid interference, wires with different signal

characteristics should be routed separately.

yYou can use the type of signal transmitted through a wire to determine

which wires should be kept separate. The rule of thumb is that wiring that

shares similar electrical characteristics can be bundled together.

yKeep input wiring and output wiring separated.

yIt is strongly advised that you label wiring to all devices in the system when

necessary.

Grounding Moxa Industrial Media

Converter

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well-grounded

mounting surface such as a metal panel.

Wiring the Alarm Contact

The Alarm Contact is made up of the two middle contacts of the terminal block

on IMC’s top panel. Refer to the next section for detailed instructions on how

to connect the wires to the terminal block connector, and how to attach the

terminal block connector to the terminal block receptor.

In this section, we explain the meaning of the two contacts used to connect the

Alarm Contact.

FAULT

Top View

Front View

FAULT: The two middle contacts of the

6-contact terminal block connector are used to

detect both power faults and port faults. The two

wires attached to the Fault contacts form an open

circuit when:

1. IMC has lost power from one of the DC

power inputs.

2. One of the ports for which the corresponding

PORT ALARM Dip Switch is set to ON is not

properly connected.

If neither of these two conditions occurs, the

Fault circuit will be closed.

Wiring the Redundant Power Inputs

The top two contacts and the bottom two contacts of the 6-contact terminal

block connector on IMC’s top panel are used for IMC’s two DC inputs. Top

and front views of one of the terminal block connectors are shown here.

Top View

Front View

STEP 1: Insert the negative/positive DC wires

into the V-/V+ terminals.

STEP 2: To keep the DC wires from pulling

loose, use a small flat-blade screwdriver to

tighten the wire-clamp screws on the front of the

terminal block connector.

STEP 3: Insert the plastic terminal block

connector prongs into the terminal block receptor,

which is located on IMC’s top panel.

ATTENTION

Before connecting IMC to the DC power inputs, make sure the DC

power source voltage is stable.

Communication Connections

IMC-101 models have one 10/100BaseT(X) Ethernet port, and one 100BaseFX

(SC or ST type connector) fiber port.

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on IMC’s front panel are used to connect to

Ethernet-enabled devices.

Below we show pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports, and also show cable wiring diagrams for

straight-through and cross-over Ethernet cables.

RJ45 (8-pin, MDI) Port Pinouts RJ45 (8-pin, MDI-X) Port Pinouts

Pin Signal

Tx+

Tx-

Rx+

Rx-

Pin Signal

Rx+

Rx-

Tx+

Tx-

RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring

Straight-Through Cable

RJ45 Plug Pin 1

Switch Port

RJ45

Connector RJ45

Connecto

Tx+

Tx-

Rx+

Rx-

NIC Port

Cable Wiring

3 3

6 6

1 1

2 2

Rx+

Rx-

Tx+

Tx-

RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring

Cross-Over Cable

RJ45 Plug Pin 1

Switch Port

(NIC Port)

RJ45

Connector RJ45

Connector

Tx+

Tx-

Rx+

Rx-

(Rx+)

(Rx-)

(Tx+)

(Tx-)

(Tx+)

(Tx-)

(Rx+)

(Rx-)

Switch Port

(NIC Port)

Cable Wiring

3 1

6 2

1 3

2 6

Rx+

Rx-

Tx+

Tx-

100BaseFX Ethernet Port Connection

The concept behind the SC port and cable is quite straightforward. Suppose

you are connecting devices I and II. Contrary to electrical signals, optical

signals do not require a circuit in order to transmit data. Consequently, one of

the optical lines is used to transmit data from device I to device II, and the

other optical line is used transmit data from device II to device I, for

full-duplex transmission.

All you need to remember is to connect the Tx (transmit) port of device I to the

Rx (receive) port of device II, and the Rx (receive) port of device I to the Tx

(transmit) port of device II. If you are making your own cable, we suggest

labeling the two sides of the same line with the same letter (A-to-A and B-to-B,

as shown below, or A1-to-A2 and B1-to-B2).

SC-Port Pinouts SC-Port to SC-Port Cable Wiring

Cable Wiring

A A

B B

ST-Port Pinouts ST-Port to ST-Port Cable Wiring

Cable Wiring

A A

B B

ATTENTION

This is a Class 1 Laser/LED product. Do not stare into the Laser

Beam.

Redundant Power Inputs

Both power inputs can be connected simultaneously to live DC power sources.

If one power source fails, the other live source acts as a backup, and

automatically supplies all of Moxa Industrial Media Converter’s power needs.

Alarm Contact

Moxa Industrial Media Converter has one Alarm Contact located on the top panel.

For detailed instructions on how to connect the Alarm Contact power wires to the

two middle contacts of the 6-contact terminal block connector, see the “Wiring the

Alarm Contact” section above. A typical scenario would be to connect the Fault

circuit to a warning light located in the control room. The light can be set up to

switch on when a fault is detected.

The Alarm Contact has two terminals that form a Fault circuit for connecting to an

alarm system. The two wires attached to the Fault contacts form an open circuit

when (1) IMC has lost power from one of the DC power inputs, or (2) one of the

ports for which the corresponding PORT ALARM Dip Switch is set to ON is not

properly connected.

If neither of these two conditions occurs, the Fault circuit will be closed.

Andere Handbücher für IMC-101 Series

Inhaltsverzeichnis

Andere Moxa Technologies Medienkonverter Handbücher

Moxa Technologies

Moxa Technologies UPort 1250I Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1110 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 1400-G2 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NE-4100 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 364 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 364A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 461A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5100A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 25 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ME61 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-P101 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies CSM-200-1213 Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 2141 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21GA Handbuch

Moxa Technologies

Moxa Technologies ME51 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ME60A Handbuch

Moxa Technologies

Moxa Technologies VPort 254 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 451 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1200 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies CSM-400 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort DE-311 Handbuch

Moxa Technologies

Moxa Technologies VPort 354 Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142 Series Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung