Moxa Technologies ICF-1170I-M-ST Bedienungsanleitung

P/N: 1802011700013

*1802011700013*

ICF-1170I Series

Quick Installation Guide

Edition 4.0, February 2017

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

Introduction

The ICF-1170I series is a CAN-to-fiber optic converter that secures data

transmission by using fiber optic transmission to provide complete

isolation and protection against EMI.

The ICF-1170I series can separate and protect critical segments of the

system from the rest of the CAN network and is protocol independent,

allowing it to work with all of the different CAN protocols and frame

lengths.

To connect two CAN devices with fiber optic cable, two ICF-1170I series

converters are required.

Why Convert CAN to Fiber?

•IMMUNITY FROM ELECTRICAL INTERFERENCE

Fiber is not affected by electromagnetic interference or radio

frequency interference; consequently it provides a clean

communication path and is immune to crosstalk.

•INSULATION

Optical fiber is an insulator; the glass fiber eliminates the need for

using electric current as the communication medium.

•SECURITY

Optical fiber provides better security compared to traditional

electrical signals transmitted through a wire or radio waves

transmitted through the air. Since the light rays travel down the

center of the fiber, it is extremely difficult for them to escape. In

addition, it is nearly impossible to tap into a fiber optic cable, and

even if a tap is successful, it is possible to detect the tap by

monitoring the optical power received at the termination point.

•RELIABILITY AND MAINTENANCE

Fiber is immune to adverse temperature and moisture conditions,

does not corrode or lose its signal, and is not affected by short circuits,

power surges, or static electricity.

Fiber Test Mode

The ICF-1170I supports a special feature called Fiber Test Mode, which

is easily activated with a DIP switch on the ICF-1170I’s outer panel.

Fiber Test Mode can be used to test the fiber cable between two

ICF-1170I units and provides a simple way to determine if the fiber cable

is transmitting data correctly.

When in Fiber Test Mode, the fiber transceiver (TX) will send out a data

signal continuously and the “Fiber TX” LED will light up. On the other side

of the connection, when the ICF-1170I fiber transceiver (RX) receives the

data signal form the TX side, the “Fiber RX” LED will light up.

- 3 -

Alarm Contact Output

The ICF-1170I supports dual power inputs for redundancy. When one

power input fails, the relay will be triggered. Be sure to install the dual

power inputs for the ICF-1170I series, and choose the correct relay

output when connecting the alarm.

Features

•Transmission distance up to 2 km

•Convert CAN signals to fiber and fiber to CAN signals

•CAN transfer rate up to 1 Mbps

•Dual power inputs for redundancy

•DIP switch for 120 Ωterminal resistance

•DIP switch for fiber test mode

•Wide temperature range model available for -40 to 85°C

environments

Package Checklist

Before installing the ICF-1170I series, verify that the package contains

the following items:

•ICF-1170I series CAN-to-fiber Converter

•Quick Installation Guide (printed)

•Warranty card

NOTE: Please notify your sales representative if any of the above items

are missing or damaged.

- 4 -

Mounting Dimensions (Unit: mm)

ICF-1170I-M-ST

Top View

Front View

- 5 -

ATTENTION

Electrostatic Discharge

Warning!

To protect the product from damage due to electrostatic

discharge, we recommend wearing a grounding device when

handling your ICF-1170 series.

Mounting

The aluminum DIN-rail attachment plate should be fixed to the back panel

of the ICF-1170I series when you take it out of the box. If you need to

reattach the DIN-rail attachment plate to the ICF-1170I, make sure the

stiff metal spring is situated towards the top, as shown in the figures

below.

Step 1:

Insert the top of the DIN

-rail into

the slot

just below the stiff metal

spring.

Step 2:

The DIN

-rail attachment unit will

snap into place as shown below

To remove the ICF-1170I series from the DIN-rail, simply reverse Steps 1

and 2 above.

Fiber Cable

ST-Port Pinouts

ST-Port to ST-Port Cable Wiring

ATTENTION

This is a Class 1 laser/LED product. Do not stare into the laser

beam.

- 6 -

Switch Settings

There are two DIP switches on the front panel of the ICF-1170I series.

120 Ω Terminator

Switch 1

Enable

Disable

OFF (default)

Fiber Test Mode

Switch 2

Enable

Disable

OFF (default)

LED Indicators

There are 4 LEDs on the front panel of the ICF-1170I.

LED

Color

Function

PWR 1

Green

Steady ON: Power source 1 is ON.

PWR 2

Green

Steady ON: Power source 2 is ON.

Fiber Tx

Green

When sending CAN data to the fiber port.

Fiber Rx

Orange

When receiving CAN data from the fiber port.

Typical CAN Application

Specifications

CAN Communication

CAN Bus Interface ISO 11898-2, Terminals (CAN_H, CAN_L,

CAN_GND)

Protocols Supported

CAN 2.0A and 2.0B (ISO 11898-2)

CAN Connector

3-pin removable screw terminal x1

Termination Resistor

Dip switch selector for 120 Ω terminal resistor

Baudrate

Up to 1 Mbps

System Delay

150 ns

Isolation Protection

2 KV

Transmission Length

Max. 2 KM (depends on the data rate and the

protocol used)

Baud Rate

Fiber Length

1000 kbps

10 m

500 kbps

100 m

250 kbps

250 m

125 kbps

400 m

50 kbps

1000 m

10 kbps

2000 m

Note: CAN Bus cable length is 30 m.

LED Indicators

PWR1, PWR2, Fiber TX, Fiber RX

Note: The transmission distance is limited by the signal rate, as

mentioned in the ISO 11898-2 standard.

- 7 -

Fiber Communication

Connector Type

ST (multimode) fiber ports x 2

Support Cable

50/125, 62.5/125, or 100/140 μm (multimode)

Wavelength

850 nm

TX Output

> -5 dBm

RX Sensitivity

-20 dBm

Environmental Limits

Operating

Temperature

0 to 60°C (32 to 140°F), 5 to 95 % RH

-40 to 85°C (-40 to 185°F) for -T model

Storage Temperature

-40 to 85°C (-40 to 185°F), 5 to 95 % RH

Power

Input Power Voltage

12 to 48 VDC dual power input for redundancy

Alarm contact

1 normal open/close output with current-carrying

capacity of 1 A@24VDC

Mechanical Specifications

Dimensions

30.3 × 70 × 115 mm

Material

Aluminum (1 mm)

Gross Weight

135 g

Regulatory Approvals

Class A

FCC

Part 15 sub Class A

UL-508

LVD

EN 60950-1

EMI

EN55032 1998, Class A

EMS EN61000-4-2 (ESD), Criteria B, Level 4

EN61000-4-3 (RS), Criteria A, Level 2

EN61000-4-4 (EFT), Criteria B, Level 4

EN61000-4-5 (Surge), Criteria B, Level 2

EN61000-4-6 (CS), Criteria B, Level 2

En61000-4-8 (PFMF), Criteria A, Level 3

Freefall

IEC 60068-2-32

MTBF

792085 hrs.

Ordering Information

Available models:

•

ICF-1170I-M-ST:

CAN

-to-fiber converter, multimode, ST

connector.

•ICF-1170I-M-ST-T:

CAN-to-fiber converter, multimode, ST

connector, -40 to 85°C.

Inhaltsverzeichnis

Andere Moxa Technologies Medienkonverter Handbücher

Moxa Technologies

Moxa Technologies NPort 5000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-S Bedienungsanleitung

Moxa Technologies

Moxa Technologies A50 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1100 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PTC-101 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate 5118 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio A52 Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 364A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCC-100 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1200 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ME50-M-SC Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort D351 Bedienungsanleitung

Moxa Technologies

Moxa Technologies MIINEPORT E1 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ME51 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-101 Series Handbuch

Moxa Technologies

Moxa Technologies ICF-1150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5600-8-DT Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 461A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 1400-G2 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio A52 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 1400-G2 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio TCC-82 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-101 Series Handbuch

Moxa Technologies

Moxa Technologies ICF-1150 series Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung