Moxa Technologies ICF-1150 series Bedienungsanleitung

P/N: 1802011500012

ICF-1150 Series

Quick Installation Guide

Third Edition, August 2013

- 2 -

Overview

Introduction

ICF-1150 series fiber converters have a multi-interface circuit that can

handle RS-232 and RS-422/485 serial interfaces, as well as multi-mode

or single-mode fiber. ICF-1150 series converters extend serial

transmission distance up to 5 km (ICF-1150-M, with multi-mode fiber) or

up to 40 km (ICF-1150-S, with single-mode fiber).

Why Convert Serial to Fiber?

Fiber communication not only extends the communication distance, but

also provides many advantageous features.

IMMUNITY FROM ELECTRICAL INTERFERENCE: Fiber is not affected by

electromagnetic interference and radio frequency interference. It

provides a clean communication path and is immune to cross-talk.

INSULATION: Optical fiber is an insulator; the glass fiber eliminates the

need for using electric currents as the communications medium.

SECURITY: Fiber cannot be tapped by conventional electronic means and

is very difficult to tap into optically. Furthermore, radio and satellite

communication signals can be captured easily for decoding.

RELIABILITY & MAINTENANCE: Fiber is immune to adverse temperature

and moisture conditions, does not corrode or lose its signal, and is not

affected by short circuits, power surges, or static electricity.

Reverse Power Protection

The Reverse Power Protection feature provides extra protection against

accidentally connecting the power cables to the wrong terminal. The

converter is designed to detect automatically which power wire is positive

and which is negative, and then adjust the power supply accordingly.

3-Way Communication

The ICF-1150 series supports 2 serial ports. The D-sub connector is for

RS-232 communication and the removable terminal block is for RS-422 or

RS-485 communication. The 3 ports (2 serial ports and one fiber port) are

completely independent. When the ICF-1150 series converters receive

data from any port, it will send data out through the other 2 ports. For

example, when the ICF-1150 series converters receive a command from

the remote Master via the fiber port, it will convert the command and

transmit it via the RS-232 port and RS-422/485 port at the same time. So

if the user is trying to monitor a system running on the RS-485 network,

there is no need to use an additional RS-232 to RS-485 converter to

connect the laptop computer’s serial port to the RS-485 bus.

ATTENTION

The ICF

1150 is designed to receive data from one port and send

data to the other ports. If the ICF

-1150 receives data from 2

ports at the same time, a data error

may occur on all of the RX

ports.

- 3 -

Rotary Switch for Setting the Pull High/Low Resistor

Since the RS-485 port can support multi-drop

connections or daisy

-chain connections, system

engineers can connect meters, RTUs, readers, and

many other devices together on the same bus. The

impedance of the data line will rise according to

the number of serial devices on the same bus. To

get the system working, the ICF

-1150 has a

setting for tuning the pull high/low resistor. Just

turn the dial to find the best resistor value for the

system without removing the ICF

-1150 from the

DIN rail.

(The default settings are 1k for both

switches.)

Pull High/Low Resistor

Position

Ohms

150k

10k

4.7k

3.3k

909

822

770

500

485

DIP Switch for Selectable Terminator

The termination resistor for many products of this type is set by a jumper

located inside the product’s casing. To disable or change the resistor’s

strength, the user must open the casing to reset the jumper. Moxa offers

a more user-friendly solution that allows users to set the termination

resistor with a DIP switch located outside the ICF-1150 converter’s

casing.

No Configuration Required for Baudrate Settings

The ICF-1150 works under any baudrate from 50 bps to 921.6 kbps. The

ICF-1150 simply converts the signal back and forth between serial

(RS-232, RS-422, or RS-485) and fiber. Since the ICF-1150 does not

need to interpret the signal, it does not need to know the baudrate of the

transmitting device. For this reason, the ICF-1150 does not have any DIP

switches or jumpers for setting the baudrate.

Ring Mode

To allow one half-duplex serial device to communicate with multiple

half-duplex devices connected to a fiber ring, you should configure the

ICF-1150 for “ring mode” by setting DIP switch “SW3” to the “On”

position. The Tx port of a particular ICF-1150 unit connects to the

neighboring converter’s Rx port to form the ring. Note that when one

node transmits a signal, the signal travels around the ring until it returns

back to the transmitting unit, which then blocks the signal. Users should

ensure that the total fiber ring length is less than 100 km when using

either single-mode models or multi-mode models.

- 4 -

Features

•“Ring” or “Point to Point” transmission

•Extend RS-232/422/485 transmission distance:

up to 40 km with single-mode—ICF-1150-S series

up to 5 km with multi-mode—ICF-1150-M series

•Supports baudrates up to 921.6 kbps

•3-way galvanic isolation (for –I models)

•Wide operating temperature from -40 to 85°C (for “T” models)

•C1D2, ATEX, and IECEx certified for harsh industrial environments

Package Checklist

Before installing the ICF-1150, verify that the package contains the

following items:

•ICF-1150 fiber converter

•Quick installation guide

•Warranty card

NOTE: Please notify your sales representative if any of the above items

are missing or damaged.

Mounting Dimensions (unit: mm)

ICF-1150-SC

- 5 -

ICF-1150-ST

Top View

Front View

ATTENTION

Electrostatic Discharge Warning!

To protect the product from damage due to e

lectrostatic

discharge, we recommend wearing a grounding device when

handling your ICF-1150 product.

- 6 -

Mounting

The aluminum DIN rail attachment plate should be fixed to the back panel

of the ICF-1150 when you take it out of the box. If you need to reattach

the DIN rail attachment plate to the ICF-1150, make sure the stiff metal

spring is situated towards the top, as shown in the figures below.

STEP 1: Insert the top of the DIN

rail into the slot just below the stiff

metal spring.

STEP 2: The DIN rail attachment

unit will snap into place as shown

below.

To remove the ICF-1150 series from the DIN rail, simply reverse Steps 1

and 2 above.

Pin Assignment

RS-232

–

TxD

RxD

–

GND

–

RS-422

4-wire RS-485

2-wire RS-485

GND

Rx-

Data -

Rx +

Data +

Tx -

–

Tx +

–

- 7 -

Fiber Cable

SC-Port Pinouts

SC-Port to SC-Port Cable Wiring

ST-Port Pinouts

ST-Port to ST-Port Cable Wiring

ATEX and IECEx Information

1. Certification number: DEMKO 10 ATEX 0917344X

IECEx UL 13.0044X

2. Ambient range: -40°C ≤Tamb ≤85°C

3. Certification string: Ex nA IIC T4 Gc

4. Standards covered: EN 60079-0:2012 IEC 60079-0: 6th Ed;

EN 60079-15:2010 IEC 60079-15:4th Ed

5. The conditions of safe usage:

•The Ethernet Communication Devices are to be mounted in a

tool-accessible ATEX-Certified or IECEx-Certified IP54 enclosure

and used in an area of not more than pollution degree 2 as

defined by IEC60664-1. A 4mm2 conductor must be used when

a connection to the external grounding screw is used.

Conductors suitable for use in an ambient temperature of 91°C

must be used for the Power Supply Terminal.

•Provisions shall be made, either in the equipment or external to

the equipment, to prevent the peak rated voltage from being

exceeded by transient disturbances of more than 140%.

ATTENTION

This is

a Class 1 laser/LED product. Do not stare into the laser

beam.

Federal Communications Commission Statement

FCC: This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

- 8 -

Switch Settings

There are 4 DIP switches on the front panel of the ICF-1150.

Setting

Switch 1

Switch 2

RS-422

OFF

2-wire RS-485

OFF

4-wire RS-485

OFF (default)

Fiber Mode

Switch 3

Ring Mode

Point to Point mode

OFF (default)

120Ω Terminator

Switch 4

Enable

Disable

OFF (default)

For Fiber Ring Users:

If the Rx LEDs of the converter glow continuously, remove the

fiber cable

and then reconnect. The Rx LEDs should no longer

glow continuously

NOTE: “Ring Mode” can only be used for half-duplex applications.

LED Indicators

There are 3 LEDs on the front panel of the ICF-1150.

LED

Color

Function

PWR

Green

Steady ON: Power is ON

Fiber Tx

Green

When sending serial data from the fiber port

Fiber Rx

Yellow

When receiving data from the fiber port

Specifications

Serial Communication

Signals for RS-232

TxD, RxD, SGND

Signals for RS-422

TxD+, TxD-, RxD+, RxD-, SGND

Signals for 4-wire RS-485

TxD+, TxD-, RxD+, RxD-, SGND

Signals for 2-wire RS-485

Data+, Data-, SGND

Baudrate

50 bps to 921.6 Kbps

ESD protection

15 kV ESD

Fiber Communication

Connector type

ST or SC

Distance

Single-mode fiber for 40 km

Multi-mode fiber for 5 km

Support Cable:

Single mode: 8.3/125, 8.7/125, 9/125 or

10/125 μm

ultimode: 50/125, 62.5/125, or 100/140

μm

Wavelength ICF-1150-S: 1310 nm

ICF-1150-M: 850 nm

TX Output

ICF-1150-S: > -5 dBm

ICF-1150-M: > -5 dBm

- 9 -

RX Sensitivity

ICF-1150-S: -25 dBm

ICF-1150-M: -20 dBm

Point-to-Point Transmission

Half or Full duplex

Multi-drop Transmission

Half duplex, fiber ring

Environmental

Operating Temperature

0 to 60°C (32 to 140°F), 5 to 95 % RH

-40 to 85°C (-40 to 185°F) for –T Model

Storage Temperature

-40 to 85°C (-40 to 185°F), 5 to 95 % RH

Power

Input Power Voltage

12 to 48 VDC

Power Line Protection

4 kV Burst (EFT), EN61000-4-4

2 kV Surge, EN61000-4-5

Reverse Power Protection

Protects against V+/V- reversal

Over Current Protection

Protects against 2 signals shorted

together: 1.1 A

Power Consumption ICF-1150-S/M-SC/ST: 127 mA @ 12 V

ICF-1150I-S/M-SC/ST: 163 mA @ 12 V

Physical Characteristics

Dimensions (W × D × H)

30.3 × 70 × 115 mm

Material

Aluminum (1 mm)

Gross Weight

135 g

Regulatory Approvals

Class B

FCC

Part 15 sub Class B

LVD

EN 60950-1

EMI

EN55022 1998, Class B

EMS

EN61000-4-2 (ESD), Criteria B, Level 4

EN61000-4-3 (RS), Criteria A, Level 3

EN61000-4-4 (EFT), Criteria B, Level 4

EN61000-4-5 (Surge), Criteria A, Level 3

EN61000-4-6 (CS), Criteria A, Level 3

En61000-4-8 (PFMF), Criteria A, Level 5

Freefall

IEC 60068-2-32

MTBF

792085 hrs

Hazardous Certifications

ATEX

Ex nA IIC T4 Gc

IECEx

IECEx UL 13.0034X

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

+1-714-528-6777

Fax:

+1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Andere Handbücher für ICF-1150 series

Inhaltsverzeichnis

Andere Moxa Technologies Medienkonverter Handbücher

Moxa Technologies

Moxa Technologies NPort 5600-8-DT Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-M-SC-RM Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-141-S Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 461 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-P101 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ME50-M-SC Bedienungsanleitung

Moxa Technologies

Moxa Technologies N Port Express Installations- und Benutzerhandbuch

Moxa Technologies

Moxa Technologies NPort 5100A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 251 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies CSM-200-1213 Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 351 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 1400-G2 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 464 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 254 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 364 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 451 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort DE-311 Handbuch

Moxa Technologies

Moxa Technologies VPort 2141 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5600-8-DT Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort D351 Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio A52 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NE-4100 Series Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung