Moxa Technologies ICF-1150 series Bedienungsanleitung

P/N: 1802011500017

*1802011500017*

ICF-1150 Series

Quick Installation Guide

Version 8.2, October 2022

Technical Support Contact Information

www.moxa.com/support



- 2 -

Overview

Introduction

The ICF-1150 series of fiber converters has a multi-interface circuit that

can handle RS-232 and RS-422/485 serial interfaces, as well as multi-

mode or single-mode fiber. ICF-1150 series converters extend serial

transmission distance up to 5 km (ICF-1150-M, with multi-mode fiber)

or up to 40 km (ICF-1150-S, with single-mode fiber).

Why Convert Serial to Fiber?

Fiber communication not only extends the communication distance but

also provides many helpful features.

IMMUNITY FROM ELECTRICAL INTERFERENCE: Fiber is not affected by

electromagnetic interference and radio frequency interference. It

provides a clean communication path and is immune to cross-talk.

INSULATION: Optical fiber is an insulator; the glass fiber eliminates the

need for using electric currents as the communications medium.

SECURITY: Fiber cannot be tapped by conventional electronic means

and is very difficult to tap into optically. Furthermore, radio and satellite

communication signals can be captured easily for decoding.

RELIABILITY & MAINTENANCE: Fiber is immune to adverse temperature

and moisture conditions, does not corrode or lose its signal, and is not

affected by short circuits, power surges, or static electricity.

Reverse Power Protection

The Reverse Power Protection feature provides extra protection against

accidentally connecting the power cables to the wrong terminal. The

converter detects automatically which power wire is positive and which

is negative, and then adjusts the power supply accordingly.

3-Way Communication

The ICF-1150 series supports 2 serial ports. The D-sub connector is for

RS-232 communication and the removable terminal block is for RS-422

or RS-485 communication. The 3 ports (2 serial ports and one fiber

port) are completely independent. When the ICF-1150 series converters

receive data from any port, it will send data out through the other 2

ports. For example, when the ICF-1150 series converters receive a

command from the remote Master via the fiber port, it will convert the

command and transmit it via the RS-232 port and RS-422/485 port at

the same time. So if the user is trying to monitor a system running on

the RS-485 network, there is no need to use an additional RS-232 to

RS-485 converter to connect the laptop computer’s serial port to the

RS-485 bus.

- 3 -

ATTENTION

The ICF

-1150 is designed to receive data from one port and

send data to the other ports. If the ICF

-1150 receives data

from 2 ports at the same time, a data error

may occur on all

the RX ports.

Rotary Switch for Setting the Pull Up/Down Resistor

Since the RS

-485 port can support multi-drop

connections or daisy

chain connections, system

engineers can connect meters, RTUs, readers,

and many other devices together on the same

bus. The impedance of t

he data line will rise

according to the number of serial devices on

the same bus. To get the system working, the

ICF

-1150 has a setting for tuning the pull

/down resistor. Just turn the dial to find the

best resistor value for the system without

removing

the ICF-1150 from the DIN rail. (The

default settings are 1k for both switches.)

Pull Up/Down Resistor

Position

Ohms

150k

10k

4.7k

3.3k

909

822

770

500

485

DIP Switch for Selectable Terminator

The termination resistor for many products of this type is set by a

jumper located inside the product’s casing. To disable or change the

resistor’s strength, the user must open the casing to reset the jumper.

Moxa offers a more user-friendly solution that allows users to set the

termination resistor with a DIP switch located outside the ICF-1150

converter’s casing.

No Configuration Required for Baudrate Settings

The ICF-1150 works under any baudrate from 50 bps to 921.6 kbps.

The ICF-1150 simply converts the signal back and forth between serial

(RS-232, RS-422, or RS-485) and fiber. Since the ICF-1150 does not

need to interpret the signal, it does not need to know the baudrate of

the transmitting device.

NOTE

The ICF-1150I default setting is auto baudrate. If you need to

use the

fixed baudrate,

then you will need to use the DIP switch

to do the configuration.

Ring Mode

To allow one half-duplex serial device to communicate with multiple

half-duplex devices connected to a fiber ring, configure the ICF-1150

for “ring mode” by setting DIP switch “SW3” to the “On” position. The

Tx port of a particular ICF-1150 unit connects to the neighboring

converter’s Rx port to form the ring. Note that when one node

transmits a signal, the signal travels around the ring until it returns to

- 4 -

the transmitting unit, which then blocks the signal. Users should ensure

that the total fiber ring length is less than 100 km when using either

single-mode models or multi-mode models.

Features

•“Ring” or “Point to Point” transmission

•Extend RS-232/422/485 transmission distance:

up to 40 km with single-mode—ICF-1150-S series

up to 5 km with multi-mode—ICF-1150-M series

•Supports baudrates up to 921.6 kbps

•3-way galvanic isolation (for –I models)

•Wide operating temperature from -40 to 85°C (for “T” models)

•C1D2, ATEX, and IECEx certified for harsh industrial environments

Package Checklist

Before installing the ICF-1150, verify that the package contains the

following items:

•ICF-1150 fiber converter

•Quick installation guide (printed)

•Warranty card

NOTE

Please notify your sales representative if any of the above

items are missing or damaged.

Mounting Dimensions (unit: mm)

ICF-1150-SC

- 5 -

ICF-1150-ST

Top View

Front View

- 6 -

ATTENTION

Electrostatic Discharge Warning!

To protect the product from

damage due to electrostatic

discharge, we recommend wearing a grounding device when

handling your ICF-1150 product.

Mounting (in an enclosure or industrial panel)

The aluminum DIN rail attachment plate should be fixed to the back

panel of the ICF-1150 when you take it out of the box. If you need to

reattach the DIN rail attachment plate to the ICF-1150, make sure the

stiff metal spring is situated towards the top, as shown in the figures

below.

STEP 1: Insert the top of the DIN

rail into the slot just below the stiff

metal spring.

STEP 2: The DIN rail attachment

unit will snap into place as shown

below.

To remove the ICF-1150 series from the DIN rail, simply reverse Steps

1 and 2 above.

Pin Assignment

RS-232

–

TxD

RxD

–

GND

–

- 7 -

RS-422

4-wire RS-485

2-wire RS-485

GND

Rx-

Data -

Rx +

Data +

Tx -

–

Tx +

–

Fiber Cable

SC-Port Pinouts

SC-Port to SC-Port Cable Wiring

ST-Port Pinouts

ST-Port to ST-Port Cable Wiring

ATEX and IECEx Information

1. Certification number:

DEMKO 10 ATEX 0917344X

IECEx UL 13.0044X

2. Ambient range:

Model

Ambient Temp. Range

Models without suffix

“-T”

0 to 60°C

Models with suffix “T”

-40 to 85°C

3. Certification string: Ex ec IIC T4 Gc

4. Standards covered: EN IEC 60079-0:2018, EN IEC 60079-7: 2015

+A1:2018

5. IEC 60079-0, Edition 7, IEC 60079-7, Edition 5.1Conditions of safe

usage:

•The Ethernet communication devices must be mounted in a

tool-accessible IP54 enclosure in accordance with IEC/EN

60079-0 and used in an area of not more than pollution

degree 2 as defined by IEC/EN 60664-1.

•Provisions shall be made to prevent that transient

disturbances should exceed the rated voltage by over 140%.

6. The Terminal blocks (J1, J2) are suitable for 14 to 28 AWG

(3.31-0.08 mm2), with torque = 1.7 lb-in. The cross-sectional area

of the PE conductor is Sp=3.31 mm2. The conductor used for

grounding is 12 AWG minimum.

7. Conductors suitable for use in an ambient temperature of 91°C

must be used for the power supply terminal.

- 8 -

ATTENTION

This is

a Class 1 laser/LED product. Do not stare into the laser

beam.

Federal Communications Commission Statement

FCC: This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

Switch Settings

There are 4 DIP switches on the front panel of the ICF-1150.

Setting

Switch 1

Switch 2

RS-422

OFF

2-wire RS-485

OFF

4-wire RS-485

OFF (default)

Fiber Mode

Switch 3

Ring Mode

Point to Point mode

OFF (default)

120Ω Terminator

Switch 4

Enable

Disable

OFF (default)

For Fiber Ring Users:

If the Rx LEDs of the converter glow continuously, remove the

fiber cable

and then reconnect. The Rx LEDs should no longer

glow

continuously.

NOTE

: “Ring Mode” can only be used for half-duplex

applications.

The S3 DIP Switch is located inside the ICF-1150. When the ICF-1150

is in RS-485 mode, use this DIP switch to configure RS-485 data

direction control, data format, and baudrate. When the ICF-1150 is in

RS-232/422 mode, the S3 DIP switch cannot affect RS-232/422

communication.

Direction Control and Data Format Setting

You will need to open the product's casing to do the Direction Control

and Data Format Setting.

- 9 -

NOTE

Direction Control and Data Format Setting require the model

version v1.2.0 or later.

RS-485 Data Direction Control Settings

RS-485 Data Direction Control

S3 Pin 1

Auto Baudrate

OFF

Fixed Baudrate

Data Format Settings

Data Format

S3 Pin 2

S3 Pin 3

S3 Pin 4

7 Bits

OFF

8 Bits

OFF

9 Bits

OFF

10 Bits

OFF

11 Bits

OFF

12 Bits

OFF

The serial data format includes one start bit, between five and eight

data bits, and one stop bit. A parity bit and an additional stop bit might

be included in the format as well.

For example, 8-N-1 is interpreted as eight data bits, with no parity bit,

and one stop bit. Users need to adjust the DIP switch to set the data

format to 10 bits.

Baudrate

S3 Pin 5

S3 Pin 6

S3 Pin 7

S3 Pin 8

S3 Pin 9

OFF

110

OFF

134.5

OFF

150

OFF

300

OFF

600

OFF

1200

OFF

1800

OFF

2400

OFF

4800

OFF

7200

OFF

9600

OFF

19200

OFF

38400

OFF

57600

OFF

115200

OFF

230400

OFF

460800

OFF

921600

OFF

LED Indicators

There are 3 LEDs on the front panel of the ICF-1150.

LED

Color

Function

PWR

Green

Steady ON: Power is ON

- 10 -

Fiber Tx

Green

When sending serial data from the fiber port

Fiber Rx

Yellow

When receiving data from the fiber port

Specifications

Serial Communication

Signals for RS-232

TxD, RxD, SGND

Signals for RS-422

TxD+, TxD-, RxD+, RxD-, SGND

Signals for 4-wire RS-485

TxD+, TxD-, RxD+, RxD-, SGND

Signals for 2-wire RS-485

Data+, Data-, SGND

Baudrate

50 bps to 921.6 Kbps

ESD protection

15 kV ESD

Fiber Communication

Connector type

ST or SC

Distance Single-mode fiber for 40 km

Multi-mode fiber for 5 km

Support Cable

Single mode:

8.3/125, 8.7/125, 9/125 or 10/125 μm

Multi-mode:

50/125, 62.5/125, or 100/140 μm

Wavelength ICF-1150-S: 1310 nm

ICF-1150-M: 850 nm

TX Output

ICF-1150-S: > -8 dBm

ICF-1150-M: > -8 dBm

RX Sensitivity ICF-1150-S: -25 dBm

ICF-1150-M: -25 dBm

Point-to-Point Transmission

Half or Full duplex

Multi-drop Transmission

Half duplex, fiber ring

Environmental

Operating Temperature 0 to 60°C (32 to 140°F), 5 to 95 % RH

-40 to 85°C (-40 to 185°F) for –T Model

Storage Temperature

-40 to 85°C (-40 to 185°F), 5 to 95 % RH

Power

Input Power Voltage

12 to 48 VDC, 300 mA (Max.) Class 2

Power Line Protection 4 kV Burst (EFT), EN61000-4-4

4 kV Surge, EN61000-4-5

Reverse Power Protection

Protects against V+/V- reversal

Over Current Protection

Protects against 2 signals shorted

together: 1.1 A

Power Consumption

ICF-1150-S/M-SC/ST: 246 mA @ 12 V

ICF-1150I-S/M-SC/ST: 300 mA @ 12 V

Physical Characteristics

Dimensions (W × D × H)

30.3 × 70 × 115 mm

Material

Aluminum (1 mm)

Gross Weight

ICF-1150 : 118g

ICF-1150I : 135g

Regulatory Approvals

Class A

FCC

Part 15 sub Class A

EMI

EN55032, Class A

EMS

EN 61000-4-2 (ESD): Contact: 8 kV; Air:

15 kV EN 61000-4-3 (RS): 80 MHz to 1

GHz: 3 V/m

EN 61000-4-4 (EFT): Power: 4 kV;

Signal: 1 kV EN 61000-4-5 (Surge):

Andere Handbücher für ICF-1150 series

Inhaltsverzeichnis

Andere Moxa Technologies Medienkonverter Handbücher

Moxa Technologies

Moxa Technologies VPort D361 Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 364A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-101 Series Handbuch

Moxa Technologies

Moxa Technologies TCF-142-M-SC-RM Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-S Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 25 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 2000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1200 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 1400-G2 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-141-S Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-S Bedienungsanleitung

Moxa Technologies

Moxa Technologies ME51 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort Z2150 Bedienungsanleitung

Moxa Technologies

Moxa Technologies PTC-101 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 464 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 254 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies A50 Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio TCC-80I Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 1250I Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio A52 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-101G Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1200 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ME50-M-SC Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort DE-311 Handbuch

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung