Moxa Technologies TCF-141-S Bedienungsanleitung

If you use DB9 for an RS-485/422 cable connection, the Pin

definition and assignments are as follows:

• RESISTOR SW

(Terminal Resistor/Pull-up and Pull-Down Res. Setting)

You may configure RESISTOR SW for proper termination or

P-UP, P-DOWN resistors for the network connection.

Fig. 2: DB9 to Fiber Converter Side Panels

The RESISTOR SW is used for RS-485/422 protocol/connection,

and takes effect when STANDARD CONFIG is at "485/422".

2. Switch Settings

The two side panels of the Converter contain a total of four sets

of DIP Switches (abbreviated SW)—labeled RS485 WIRING,

DB9 CONFIG, STANDARD CONFIG, and RESISTOR—that

are used to configure the various data transmission modes. The

proper configuration of each of these four sets of DIP Switches

is described below:

RESISTOR SW default: 1, 2, 3, 4. All are at "OFF"

RX-TERM ON: Enables 130Ωterminator on RX

TX-TERM ON: Enables 130Ωterminator on TX

P-DOWN ON: Enables 1 KΩpull down on

RS422 TXor

RS485(2-wire)TX/RX-

• STANDARD CONFIG

For selecting serial port protocol: RS-232 or RS-485/422.

P-UP ON : Enables 1 KΩpull up on

RS422 TX+ or

RS485(2-wire)TX/RX+

RS232: RS-232 protocol/connection, default.

485/422: RS-485/422 protocol/connection.

• RS485 WIRING

Note:

For selecting between 2-wire and 4-wire RS-485.

The way in which the termination and P-UP, P-DOWN resistors

are set up depends on the RS-485/422 network configuration.

2wire: 2-wire at half-duplex mode.

4wire: 4-wire at full-duplex mode, default.

• DB9 CONFIG

• Ensure that the copper cable and its voltage polarity match

the device requirements for a 4-wire or 2-wire connection.

232: RS-232/DB9 connection, default.

485/422: RS-485/422 via DB9 port

• Improper termination and network configuration will cause

the devices to work poorly.

NOTE: The STANDARD CONFIG and DB9 CONFIG DIP

Switch settings must agree. Either set both to RS-232, or set

both to RS-485/422.

3. LED Description

• When thee Rx-TERM & TX-TERM switches are enabled,

both P-Down & P-Up DIP switches should be on as well.

For DB9 model and port connection, the available

connections by the three SW settings are:

• DB9 Connector for Copper Wires

Protocol &

Connection

STANDARD

CONFIG SW

DB9 CONFIG

RS485

WIRING SW

RS-232 RS232 232 ---

4-wire RS-485 485/422 485/422 4wire

2-wire RS-485 485/422 485/422 2wire

RS-422 485/422 485/422 4wire

RS-232 protocol/connection via DB9

LED Color Function

F (FX ACT) Green Blinks when fiber data is received

C (Copper ACT) Green Blinks when Copper data is

received

PWR Green Lit when +5V power is coming up

RS-232 Cable Connection via DB9

RXD

2 3 TXD

TXD 3 2 RXD

GND 5 5 GND

RS-485/422 protocol/connection via DB9

1 RS-485/422 TX- or RS-485

(

2-wire

)

TX/RX-

2 RS-485/422 TX+ or RS-485

(

2-wire

)

TX/RX+

3 RS-485/422 RX+

4 RS-485/422 RX-

5 Signal Ground

Unused 6

Unused 7

Unused 8

Unused 9

Fig. 6: RS-485/422/232 to ST Fiber Converter Front Panel

Optic Fiber Port

TX RX

PWR

RS-485/422/232

Fiber Media Converter

DB9 or

Terminal Block

RS485/422/232 Port

. 5: RS-485/422/232 Fiber O

tic Network Connection

RS-232

RS-422

RS-485

DB9 or

Terminal

Block

Fiber Optic Wire

RS-485/422/232

DB9, Terminal

Fiber Converter

Copper Wire

1 Unuse

2 RS-232 RXD

3 RS-232 TXD

4 Unuse

5 Signal Ground

Unused 6

Unused 7

Unused 8

Unused 9

4. DC Jack and AC-DC Power Adapter

The DC jack's central post is 2.5 mm wide and conforms to the

dimensions of the DC receptacle (2.5 mm).

AC-DC adapters that use different AC input voltages are available

for different areas.

North America 120VAC 60Hz

Europe 230VAC 50Hz

U.K. 230VAC 50Hz

South Africa 240VAC 50Hz

Australia 240VAC 50Hz

AC Input:

Japan 100VAC 50/60Hz

DC Output: 5VDC @ 1.0A

5. Fiber Technical Specifications

• Standards: TIA/EIA-232(ITU-T V.28)

TIA/EIA-422(ITU-T V.11)

TIA/EIA-485(ISO/IEC8284)

• Model Description:

Model Interface Fiber Type λ(nm) Distance

TCF-141-M DB9(male) ST multi-mode 820 2Km

TCF-141-S DB9(male) ST single-

mode 1310 20Km

• Data Transfer Rate and Maximum Cable Distance

Connection Max. Rate (bps) Max. Distance

RS-232 115.2K 15 m (50 ft)

RS-422/485 90K 1220 m (4000 ft)

RS-422/485 500K 92 m (300 ft)

Multi-Mode Fiber * 2 km

Single-Mode Fiber * 20 km

* Fiber Optic Rate depends on the Copper Port speed

• Copper Wires:24 to 22 AWG gauge

Attenuation 20dB/1000ft @ 10 MHz

Differential Impedance 100Ω@ 10 MHz

• Fiber Cable:

50/125, 62.5/125, or 100/140

m multi-mode

8.3/125, 8.7/125, 9/125, or 10/125

m single-mode

• Data Transfer Rate: up to 115.2 Kbps (RS-232)

up to 500 Kbps (RS-485/422)

• Power Requirement: 1A@+5 VDC

• Ambient Temperature: 0 to 50°C

• Humidity: 5 to 90% RH

• Dimensions: 26.2(H) ×70.3(W) ×94(D) mm

• Complies with FCC Part 15 Class B and CE Mark

Note:

When connecting this device to a Router, Bridge or Switch,

please refer to the corresponding device's Technical Manual for

detailed technical information.

Moxa Technologies Co., Ltd.

Tel: +866-2-8919-1230

Fax: +886-2-8919-1231

www.moxa.com

[email protected]

2nd Edition

P/N: 18020014101

TCF-141-S, TCF-141-M

RS-485/422/232 to Fiber Converter

(DB9 to ST Fiber)

User's Manual

1. Overview

RS-485/422/232 to fiber optic converters are used to extend

serial transmission distance up to 2 km (using multi-mode fiber)

or up to 20 km (using single-mode fiber). The TCF-141-S (TCF-

141-M) Converter is equipped with a multiple interface circuit

that can handle RS-232, RS-422, and RS-485 serial interfaces.

6. Package Checklist

Before installing the Converter, verify that the package contains

the following items:

• The RS-485/422/232 to Fiber Converter

• AC-DC Power Adapter

• This User's Manual

Notify your sales representative immediately if any of the above

items is missing or damaged.

7. Installing the Converter

Note: The Media Converter is hot-swappable.

• Wear a grounding device for electrostatic discharge.

• Verify that the AC-DC adapter conforms to your country’s

AC power requirement and then insert the power plug.

• Install the media cable for network connection.

TCF-141-M

Fig. 1: RS-485/422/232 DB9 to Fiber Converter

DC Jack : 2.5mm

DC Input : +5V

(RS-C200

DC current: full load consumption 0.5A)

Fig. 7: DC+5V Input Jack and Dimensions

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Medienkonverter Handbücher

Moxa Technologies

Moxa Technologies ICF-1170I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-101 Series Handbuch

Moxa Technologies

Moxa Technologies VPort 254 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-90 Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 364A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-101 Series Handbuch

Moxa Technologies

Moxa Technologies VPort 251 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies CSM-400 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio A52 Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCC-80I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 351 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 2210 Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 351 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21 Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 251 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCC-120 Handbuch

Moxa Technologies

Moxa Technologies NPort 5600-8-DT Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio TCC-80I Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 451 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-P101 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 461 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 1400-G2 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1180I Series Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung