National Instruments PCI-FBUS Bedienungsanleitung

INSTALLATION GUIDE

Foundation Fieldbus Hardware

and NI-FBUS Software

This guide contains installation and configuration instructions for the PCI-FBUS,

PCMCIA-FBUS, and USB-8486.

Note Install the NI-FBUS software before you install the hardware.

Contents

Installing the Software.............................................................................................................. 1

Installing the Hardware ............................................................................................................ 2

Install Your PCI-FBUS Card............................................................................................ 2

Install Your PCMCIA-FBUS Card................................................................................... 3

Install Your USB-8486..................................................................................................... 4

Installing the Software

Complete the following steps to install the NI-FBUS software.

Caution If you are reinstalling the NI-FBUS software over a previous version,

write down your card configuration and any port configuration parameters you

changed from their defaults. Reinstalling the software may cause you to lose any

existing card and port configuration information.

1. Log in as Administrator or as a user that has Administrator privileges.

2. Insert the NI-FBUS Software media into the computer.

If the installer does not launch automatically, use Windows Explorer to navigate to the

installation media and launch the autorun.exe file.

3. The interactive setup program guides you through the necessary steps to install the

NI-FBUS software. You may go back and change values where appropriate by clicking

Back. You can exit the setup where appropriate by clicking Cancel.

4. Power down your computer when the setup is complete.

5. Continue to the Installing the Hardware section to configure and install your hardware.

™

2|ni.com |Foundation Fieldbus Hardware and NI-FBUS Software Installation Guide

Installing the Hardware

This section describes how to install your PCI-FBUS, PCMCIA-FBUS, and USB-8486.

Note Here, the term PCI-FBUS represents PCI-FBUS/2; the term PCMCIA-FBUS

represents PCMCIA-FBUS, PCMCIA-FBUS/2, PCMCIA-FBUS Series 2, and

PCMCIA-FBUS/2 Series 2.

Install Your PCI-FBUS Card

Caution Before you remove the card from the package, touch the antistatic plastic

package to a metal part of the system chassis to discharge electrostatic energy, which

can damage several components on the PCI-FBUS card.

To install the PCI-FBUS card, complete the following steps.

1. Shut down and power off the computer. Keep the computer plugged in so that it remains

grounded while you install the PCI-FBUS card.

2. Remove the top cover or access port of the I/O channel.

3. Remove the expansion slot cover on the back panel of the computer.

4. As shown in Figure 1, insert the PCI-FBUS card into any unused PCI slot with the Fieldbus

connector protruding from the opening on the back panel. Make sure all pins are inserted an

equal depth into the connector. Although it might be a tight fit, do not force the card into place.

Figure 1. Installing the PCI-FBUS Card

Personal

Computer

PCI/ISA Slot

PCI-FBUS

Foundation Fieldbus Hardware and NI-FBUS Software Installation Guide |© National Instruments |3

5. Screw the mounting bracket of the PCI-FBUS card to the back panel rail of the computer.

6. Keep the top cover or access port off until you have verified that the hardware resources do

not conflict.

7. Power on the computer.

8. Launch the Interface Configuration Utility. Find the PCI-FBUS card and right-click to enable.

9. Close the Interface Configuration Utility and start the NI-FBUS Communications Manager

or NI-FBUS Configurator.

Install Your PCMCIA-FBUS Card

Caution Before you remove the card from the package, touch the antistatic plastic

package to a metal part of the system chassis to discharge electrostatic energy, which

can damage several components on the PCMCIA-FBUS card.

To install the PCMCIA-FBUS card, complete the following steps.

1. Power on the computer and allow the operating system to boot.

2. Insert the card into a free PCMCIA (or Cardbus) socket. The card has no jumpers or

switches to set. Figure 2 shows how to insert the PCMCIA-FBUS and how to connect the

PCMCIA-FBUS cable and connector to the PCMCIA-FBUS card. However, the

PCMCIA-FBUS/2 cable has two connectors. Refer to Chapter 2, Connector and Cabling,

of the NI-FBUS Hardware and Software User Manual, for more information about these

two connectors.

4|ni.com |Foundation Fieldbus Hardware and NI-FBUS Software Installation Guide

Figure 2. Inserting the PCMCIA-FBUS Card

3. Connect the PCMCIA-FBUS to the Fieldbus network.

Your kit contains a PCMCIA-FBUS cable. Refer to Chapter 2, Connector and Cabling, of

the NI-FBUS Hardware and Software User Manual, if you need a longer cable than the

PCMCIA-FBUS cable provided.

Install Your USB-8486

Caution Operate the USB-8486 only as described in the operating instructions.

Do not unplug the USB-8486 when the NI-FBUS software is running.

The USB-8486 has the following two variants:

• USB-8486 without screw retention and mounting option

• USB-8486 with screw retention and mounting option

You can connect the USB-8486 without screw retention and mounting option to a desktop PC or

a laptop PC.

1 Portable Computer 2 PCMCIA Socket 3 PCMCIA-FBUS Cable

Foundation Fieldbus Hardware and NI-FBUS Software Installation Guide |© National Instruments |5

Figure 3. Connecting the USB-8486 to a Desktop PC

Figure 4. Connecting the USB-8486 to a Laptop PC

1 Desktop PC 2USB-8486 3 DB-9 Connector

1 Portable Computer 2 USB Port 3USB-8486 4 DB-9 Connector

6|ni.com |Foundation Fieldbus Hardware and NI-FBUS Software Installation Guide

To install the USB-8486, complete the following steps.

1. Power on the computer and allow the operating system to boot.

2. Insert the USB-8486 into a free USB port, as shown in Figure 3 and Figure 4.

3. Connect the USB-8486 to the Fieldbus network. Refer to the NI-FBUS Hardware and

Software User Manual for more information about the connectors.

4. Launch the Interface Configuration Utility.

5. Right-click the USB-8486 to enable if it is disabled.

6. Close the Interface Configuration Utility and start the NI-FBUS Communications Manager

or NI-FBUS Configurator.

Mount and Connect Your USB-8486

You can attach the USB-8486 with screw retention and mounting option to a CompactRIO. This

device provides the following mounting options:

• DIN mount using the unthreaded DIN rail mounting holes

• Panel mount using the panel mount notch and tab

Foundation Fieldbus Hardware and NI-FBUS Software Installation Guide |© National Instruments |7

DIN Rail Mounting

You can use the DIN-rail mounting kit to mount your USB-8486 to a standard DIN rail, as shown

in Figure 5.

Figure 5. Fastening a DIN Rail Clip to the USB-8486

1 USB-8486 2 DIN Rail Clip 3 Thread-Forming Screws

8|ni.com |Foundation Fieldbus Hardware and NI-FBUS Software Installation Guide

Complete the following steps to mount the device to a DIN rail vertically by using the

unthreaded mounting holes.

1. Fasten a DIN rail clip to the device using a #1 Phillips screwdriver and four thread-forming

screws included in the DIN-rail mounting kit. Tighten the screws to a torque of 0.76 N · m

(6.7 lb · in.). Figure 5 shows a DIN rail clip being attached to the device.

2. Clip the device onto the DIN rail as shown in Figure 6.

Note Using the thread-forming screws permanently affixes the DIN rail clip to the

device. Unscrewing and reinstalling the thread-forming screws produces a

compromised connection between the DIN rail and the device.

Figure 6. Clipping the USB-8486 to a DIN Rail

You can mount the device to a DIN rail horizontally by using the additional screw positions.

1 DIN Rail 2 DIN Rail Clip 3USB-8486

Foundation Fieldbus Hardware and NI-FBUS Software Installation Guide |© National Instruments |9

Panel Mounting

You can use #8 or M4 pan head screws to mount the USB-8486 to a board or panel, as shown in

Figure 7.

Figure 7. Mounting the USB-8486 to a Broad or Panel

To mount the USB-8486 to a board or panel, complete the following steps:

1. Screw a #8 or M4 pan head screw into the lower point on the panel.

2. Set the USB-8486 on the screw by fitting the screw head into the bottom screw notch on

the underside of the enclosure.

3. Screw a #8 or M4 pan head screw through the upper mounting tab on the USB-8486.

1 #8 or M4 Pan Head Screw 2 USB-8486 3 #8 or M4 Pan Head Screw

10 |ni.com |Foundation Fieldbus Hardware and NI-FBUS Software Installation Guide

Figure 8 shows the distance between the bottom screw notch and the upper mounting tab on the

USB-8486.

Figure 8. Dimensions of the Mounting Tab and Notch

15.24 mm

(0.600 in.)

78.22 mm

(3.079 in.)

Andere Handbücher für PCI-FBUS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere National Instruments PCI-Karte Handbücher

National Instruments

National Instruments PCI-6509 Bedienungsanleitung

National Instruments

National Instruments IMAQ PCI-1408 Bedienungsanleitung

National Instruments

National Instruments R Series Bedienungsanleitung

National Instruments

National Instruments DAQ PCI-4451 Bedienungsanleitung

National Instruments

National Instruments PCI-232/2 Bedienungsanleitung

National Instruments

National Instruments NI PXI/PCI-1428 Bedienungsanleitung

National Instruments

National Instruments IMAQ PXI-1411 Bedienungsanleitung

National Instruments

National Instruments R Series Bedienungsanleitung

National Instruments

National Instruments PCIe-5775 Bedienungsanleitung

National Instruments

National Instruments MXI-Express x4 Series Bedienungsanleitung

National Instruments

National Instruments PCI-GPIB Bedienungsanleitung

National Instruments

National Instruments PCI-1407 Bedienungsanleitung

National Instruments

National Instruments MXI PXI Express Series Bedienungsanleitung

National Instruments

National Instruments NI PCI-1424 Bedienungsanleitung

National Instruments

National Instruments 6034E Bedienungsanleitung

National Instruments

National Instruments IMAQ PCI-1422 Bedienungsanleitung

National Instruments

National Instruments PXI-1407 Bedienungsanleitung

National Instruments

National Instruments NI PCIe-8255R Bedienungsanleitung

National Instruments

National Instruments DAQ X Series Bedienungsanleitung

National Instruments

National Instruments PCIe-1477 Bedienungsanleitung

National Instruments

National Instruments IMAQ PCI-1426 Bedienungsanleitung

National Instruments

National Instruments IMAQ PCI-1409 Bedienungsanleitung

National Instruments

National Instruments NI PXI/PCIe-8231 Bedienungsanleitung

National Instruments

National Instruments PCI-6703 Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung