National Instruments IMAQ PXI-1411 Bedienungsanleitung

Getting Started with the NI PXI/PCI-1411

The NI PXI/PCI-1411 (NI 1411) is a monochrome and color image acquisition device for PXI, PCI, or

CompactPCI. This document describes how to install and configure the necessary hardware and

software components to begin using the NI 1411.

What You Need to Get Started

You need the following items to set up and use the NI 1411:

❑NI 1411 image acquisition device

❑Video camera or other video device

❑BNC cable, included with the NI 1411

❑S-Video cable (optional)

❑PXI, PCI, or CompactPCI computer running Microsoft Windows Vista/XP/2000 with at least

one available slot

Note Visit ni.com/info and enter rdvisionvista for more information about National

Instruments image acquisition device compatibility with Windows Vista.

❑NI Vision Acquisition Software 8.0 or later, which includes the NI-IMAQ driver software

❑Optional software for developing applications:

– NI Vision Builder for Automated Inspection

– NI Vision Development Module

–LabVIEW

– LabWindows™/CVI™

– Microsoft Visual Basic

Related Documentation

The following documents contain additional information that you may find helpful:

•NI PXI/PCI-1411 User Manual—Contains information about programming options, hardware

functionality, and signal connections.

•NI Vision Acquisition Software Release Notes—Contains information about new functionality,

minimum system requirements, and installation instructions for the NI-IMAQ driver software.

•Measurement & Automation Explorer Help for NI-IMAQ—Describes how to configure the

NI-IMAQ driver software, NI image acquisition devices, and cameras using Measurement &

Automation Explorer (MAX).

•NI-IMAQ Help—Contains fundamental programming concepts for the NI-IMAQ driver software

and terminology for using NI image acquisition devices.

GS_NI_1411.fm Page 1 Wednesday, January 31, 2007 5:29 PM

Getting Started with the NI PXI/PCI-1411 2 ni.com

Safety Information

Caution The following paragraphs contain important safety information you must follow when

installing and operating the device.

Do not operate the device in a manner not specified in the documentation. Misuse of the device may

result in a hazard and may compromise the safety protection built into the device. If the device is

damaged, turn it off and do not use it until service-trained personnel can check its safety. If necessary,

return the device to National Instruments for repair.

Keep away from live circuits. Do not remove equipment covers or shields unless you are trained to do

so. If signal wires are connected to the device, hazardous voltages can exist even when the equipment is

turned off. To avoid a shock hazard, do not perform procedures involving cover or shield removal unless

you are qualified to do so. Disconnect all field power prior to removing covers or shields.

If the device is rated for use with hazardous voltages (>30 Vrms, 42.4 Vpk, or 60 Vdc), it may require a

safety earth-ground connection wire. Refer to the device specifications for maximum voltage ratings.

Because of the danger of introducing additional hazards, do not install unauthorized parts or modify the

device. Use the device only with the chassis, modules, accessories, and cables specified in the

installation instructions. All covers and filler panels must be installed while operating the device.

Do not operate the device in an explosive atmosphere or where flammable gases or fumes may be

present. Operate the device only at or below the pollution degree stated in the specifications. Pollution

consists of any foreign matter—solid, liquid, or gas—that may reduce dielectric strength or surface

resistivity. The following is a description of pollution degrees.

• Pollution Degree 1—No pollution or only dry, nonconductive pollution occurs. The pollution has

no effect.

• Pollution Degree 2—Normally only nonconductive pollution occurs. Occasionally, nonconductive

pollution becomes conductive because of condensation.

• Pollution Degree 3—Conductive pollution or dry, nonconductive pollution occurs. Nonconductive

pollution becomes conductive because of condensation.

Clean the device and accessories by brushing off light dust with a soft, nonmetallic brush. Remove other

contaminants with a stiff, nonmetallic brush. The unit must be completely dry and free from

contaminants before returning it to service.

Yo u must insulate signal connections for the maximum voltage for which the device is rated. Do not

exceed the maximum ratings for the device. Remove power from signal lines before connection to or

disconnection from the device.

Caution National Instruments measurement products may be classified as either Measurement

Category I or II. Operate products at or below the Measurement Category level specified in the

hardware specifications.

Measurement Category1: Measurement circuits are subjected to working voltages2and transient

stresses (overvoltage) from the circuit to which they are connected during measurement or test.

Measurement Category establishes standardized impulse withstand voltage levels that commonly occur

1 Measurement Categories as defined in electrical safety standard IEC 61010-1.

2 Working voltage is the highest rms value of an AC or DC voltage that can occur across any particular insulation.

GS_NI_1411.fm Page 2 Wednesday, January 31, 2007 5:29 PM

©National Instruments Corporation 3 Getting Started with the NI PXI/PCI-1411

in electrical distribution systems. The following is a description of Measurement (Installation1)

Categories:

• Measurement Category I is for measurements performed on circuits not directly connected to the

electrical distribution system referred to as MAINS2voltage. This category is for measurements of

voltages from specially protected secondary circuits. Such voltage measurements include signal

levels, special equipment, limited-energy parts of equipment, circuits powered by regulated

low-voltage sources, and electronics.

• Measurement Category II is for measurements performed on circuits directly connected to the

electrical distribution system. This category refers to local-level electrical distribution, such as that

provided by a standard wall outlet (e.g., 115 V for U.S. or 230 V for Europe). Examples of

Measurement Category II are measurements performed on household appliances, portable tools,

and similar products.

• Measurement Category III is for measurements performed in the building installation at the

distribution level. This category refers to measurements on hard-wired equipment such as

equipment in fixed installations, distribution boards, and circuit breakers. Other examples are

wiring, including cables, bus-bars, junction boxes, switches, socket-outlets in the fixed installation,

and stationary motors with permanent connections to fixed installations.

Unpacking

The NI 1411 ships in an antistatic package to prevent electrostatic discharge from damaging device

components. To avoid such damage in handling your device, take the following precautions:

1. Ground yourself using a grounding strap or by touching a grounded object, such as the computer

chassis.

2. Touch the antistatic package to a metal part of the computer chassis before removing the device

from the package.

Caution Never touch the exposed pins of connectors.

3. Remove the device from the package and inspect it for loose components or any other signs of

damage. Notify National Instruments if the device appears damaged in any way. Do not install

a damaged device in the computer.

Store the NI 1411 in the antistatic package when not in use.

Installation

The following instructions are for general installation. Refer to the documentation provided by your

computer manufacturer for specific instructions and warnings. Refer to the Specifications section for

typical power requirements for the NI 1411.

NI PXI-1411

You can install an NI PXI-1411 in any available 5 V peripheral slot in a PXI or CompactPCI chassis.

1. Install the NI Vision Acquisition Software before installing the NI PXI-1411. Refer to the NI Vision

Acquisition Software Release Notes for specific installation instructions.

2. Power off and unplug the PXI or CompactPCI chassis.

1 Measurement Category is also referred to as Installation Category.

2 MAINS is defined as the (hazardous live) electrical supply system to which equipment is designed to be connected for the

purpose of powering the equipment. Suitably rated measuring circuits may be connected to the MAINS for measuring

purposes.

GS_NI_1411.fm Page 3 Wednesday, January 31, 2007 5:29 PM

Getting Started with the NI PXI/PCI-1411 4 ni.com

Caution To protect yourself and the computer from electrical hazards, the computer must remain

unplugged until the installation is complete.

3. Choose an unused PXI or CompactPCI 5 V slot that supports bus arbitration or bus-master cards.

PXI-compliant chassis must have bus arbitration for all slots.

4. Remove the filler panel for the slot you have chosen.

5. Touch a metal part of the chassis to discharge any static electricity that might be on your clothes or

body. Static electricity can damage the device.

6. Insert the NI PXI-1411 in the selected 5 V slot. Use the injector/ejector handle to fully inject the

device into place.

7. Secure the front panel of the NI PXI-1411 to the front panel mounting rails of the PXI or

CompactPCI chassis.

8. Connect the BNC cable included with the NI PXI-1411 to the camera. Refer to your camera

manufacturer documentation for specific instructions about how to connect the cable to your

camera.

9. Connect the BNC cable to the VIDEO connector on the NI PXI-1411 front panel.

10. Plug in and power on the PXI or CompactPCI chassis.

The NI PXI-1411 is now installed and the camera is connected.

NI PCI-1411

1. Install the NI Vision Acquisition Software before installing the NI PCI-1411. Refer to the NI Vision

Acquisition Software Release Notes for specific installation instructions.

2. Power off and unplug the computer.

Caution To protect yourself and the computer from electrical hazards, the computer must remain

unplugged until the installation is complete.

3. Remove the computer cover to expose the expansion slots.

4. Touch a metal part of the computer to discharge any static electricity that might be on your clothes

or body. Static electricity can damage the device.

5. Choose an unused PCI slot, and remove the corresponding expansion slot cover on the back panel

of the computer.

6. Remove your device from the antistatic package and gently rock the device into the slot. The

connection may be tight, but do not force the device into place.

Note Check that the bracket of the device aligns with the hole in the back panel rail of the computer

chassis.

7. Secure the device mounting bracket to the back panel rail of the computer.

8. Replace the computer cover.

9. Connect the BNC cable included with the NI PCI-1411 to the camera. Refer to your camera

manufacturer documentation for specific instructions about how to connect the cable to your

camera.

10. Connect the BNC cable to the VIDEO connector on the NI PCI-1411 front panel.

11. Plug in and power on the computer.

The NI PCI-1411 is now installed and the camera is connected.

GS_NI_1411.fm Page 4 Wednesday, January 31, 2007 5:29 PM

©National Instruments Corporation 5 Getting Started with the NI PXI/PCI-1411

Configuring the NI 1411

After you have installed the NI 1411 and powered on the computer, the computer will recognize the

device and assign resources to it. Use Measurement & Automation Explorer (MAX), the National

Instruments configuration utility, to configure the NI 1411 for acquisition. Refer to the Measurement &

Automation Explorer Help for NI-IMAQ for additional information about configuring the NI 1411.

Note Before configuring the device in MAX, ensure that you installed the NI-IMAQ driver

software.

Specifications

The following specifications apply to the NI 1411 image acquisition device. These specifications are

typical at 25 °C unless otherwise specified.

Formats Supported

Input formats

RS-170/NTSC................................................29.97 frames/s

CCIR/PAL......................................................25 frames/s

Output formats

RGB ..............................................................32-bit

HSL................................................................32-bit

R, G, B, H, S, or L .........................................8-bit

Pixel aspect ratio ............................................Square pixel

Video Input

Quantity .................................................................1 (VIDEO)

VIDEO ...................................................................Composite video on BNC (RSE), Y/C on S-Video

connector (RSE)

Input impedance.....................................................75 Ω ± 1%

Input range (blank to white)...................................700 mV (calibrated) or

400 mV to 1.00 V (variable gain)

(PCI-1411 revision C and later,

PXI-1411 revision A and later)

Frequency response (luminance)

Full range .......................................................12 MHz (–3 dB) typ

(all filters off)

Programmable................................................Decimation and lowpass filters

GS_NI_1411.fm Page 5 Wednesday, January 31, 2007 5:29 PM

Getting Started with the NI PXI/PCI-1411 6 ni.com

Accuracy

Absolute accuracy1

Luma gain ......................................................± 2.5% of reading

Chroma gain...................................................± 2.5% of reading

Temperature drift ...........................................<250 ppm/°C

A/D Conversion

Quantity .................................................................One 8-bit 2X oversampling for composite video

Two 8-bit 2X oversampling for Y/C (S-Video)

Dynamic range.......................................................46 dB typ

Sampling Frequency

RS-170/NTSC................................................27.54 MHz (double rate of square pixel)

CCIR/PAL......................................................29.5 MHz (double rateof square pixel)

Color Decoding

Composite video

Luma path ......................................................Chroma trap filter and/or line comb

Chroma path...................................................Bandpass filter and/or line comb

Memory

Onboard memory ...................................................16 MB synchronous dynamic RAM

LUTs ......................................................................Three 256 ×8 (RGB only)

External Connections

Trigger sense ..........................................................TTL

Trigger level...........................................................Programmable (rising or falling)

PCI Interface

PCI initiator (master) capability ............................Supported

PCI target (slave) capability...................................Supported

Data path ................................................................32 bits

Board voltage .........................................................5 V, 12 V, –12 V

Board type..............................................................32-bit half-size card

Parity generation/checking, error reporting ...........Supported

Target decode speed ...............................................Medium (1 clock)

1 Calibration conditions:

White level 700 mV

Contrast 1.00

Saturation 1.00

Brightness 1.00

Luma bandwidth Full

Ambient temperature 25 °C nominal

GS_NI_1411.fm Page 6 Wednesday, January 31, 2007 5:29 PM

©National Instruments Corporation 7 Getting Started with the NI PXI/PCI-1411

Target fast back-to-back capability ........................Supported

Resource locking....................................................Supported as a master and slave

PCI interrupts.........................................................Interrupts passed on INTA# signal

Base address registers ............................................BAR0 (16 KB)

BAR1 (64 KB)

Expansion ROM.....................................................4 KB

PCI master performance

Ideal ...............................................................133 Mbytes/s

Sustained........................................................100 Mbytes/s

Power Requirements

Voltage ...................................................................+5 V (1.00 A)

+12 V (75 mA)

Physical

Dimensions

PCI-1411........................................................10.7 ×17.5 cm (4.2 ×6.9 in.)

PXI-1411........................................................10 ×16 cm (3.9 ×6.3 in.)

Weight

PCI-1411........................................................0.136 kg (0.3 lb)

PXI-1411........................................................0.154 kg (0.34 lb)

Environment

Operating temperature ........................................... 0 °C to 55 °C

Storage temperature ...............................................–20 °C to 70 °C

Relative humidity...................................................5%–90%, noncondensing

MTBF.....................................................................839,653 h at 30 °C

Emissions ...............................................................EN 55011:1991 Group 1 Class A at 10 m FCC

Class A at 10 m

Functional shock (PXI only)..................................MIL-T-28800 E Class 3 (per Section 4.5.5.4.1)

Half-sine shock pulse, 11 ms duration, 30 g peak,

30 shocks per face

Operational random vibration

(PXI only) ..............................................................5 to 500 Hz, 0.31 grms, 3 axes

Nonoperational random vibration

(PXI only) ..............................................................5 to 500 Hz, 2.5 grms, 3 axes

Note Random vibration profiles were developed in accordance with MIL-T-28800E and

MIL-STD-810E Method 514. Test levels exceed those recommended in MIL-STD-810E for

Category 1 (Basic Transportation, Figures 514.4-1 through 514.4-3).

Approved at altitudes up to 2,000 m.

GS_NI_1411.fm Page 7 Wednesday, January 31, 2007 5:29 PM

Getting Started with the NI PXI/PCI-1411 8 ni.com

Safety

This product is designed to meet the requirements of the following standards of safety for electrical

equipment for measurement, control, and laboratory use:

• IEC 61010-1, EN-61010-1

• UL 61010-1, CSA 61010-1

Note For UL and other safety certifications, refer to the product label or visit

ni.com/certification, search by model number or product line, and click the appropriate link

in the Certification column.

Electromagnetic Compatibility

This product is designed to meet the requirements of the following standards of EMC for electrical

equipment for measurement, control, and laboratory use:

• EN 61326 EMC requirements; Minimum Immunity

• EN 55011 Emissions; Group 1, Class A

• CE, C-Tick, ICES, and FCC Part 15 Emissions; Class A

Note For EMC compliance, operate this device to product documentation.

CE Compliance

This product meets the essential requirements of applicable European Directives, as amended for

CE marking, as follows:

• 73/23/EEC; Low-Voltage Directive (safety)

• 89/336/EEC; Electromagnetic Compatibility Directive (EMC)

Note Refer to the Declaration of Conformity (DoC) for this product for any additional

regulatory compliance information. To obtain the DoC for this product, visit ni.com/

certification, search by model number or product line, and click the appropriate link

in the Certification column.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers At the end of their life cycle, all products must be sent to a WEEE recycling center.

For more information about WEEE recycling centers and National Instruments WEEE initiatives,

visit ni.com/environment/weee.htm.

Where to Go for Support

The National Instruments Web site is your complete resource for technical support. At

ni.com/support you have access to everything from troubleshooting and application development

self-help resources to email and phone assistance from NI Application Engineers.

A Declaration of Conformity (DoC) is our claim of compliance with the Council of the European

Communities using the manufacturer’s declaration of conformity. This system affords the user

protection for electronic compatibility (EMC) and product safety. You can obtain the DoC for your

product by visiting ni.com/certification. If your product supports calibration, you can obtain

the calibration certificate for your product at ni.com/calibration.

National Instruments corporate headquarters is located at 11500 North Mopac Expressway, Austin,

Texas, 78759-3504. National Instruments also has offices located around the world to help address your

support needs. For telephone support in the United States, create your service request at

GS_NI_1411.fm Page 8 Wednesday, January 31, 2007 5:29 PM

©National Instruments Corporation 9 Getting Started with the NI PXI/PCI-1411

ni.com/support and follow the calling instructions or dial 512 795 8248. For telephone support

outside the United States, contact your local branch office:

Australia 1800 300 800, Austria 43 662 457990-0, Belgium 32 (0) 2 757 0020,

Brazil 55 11 3262 3599, Canada 800 433 3488, China 86 21 6555 7838,

Czech Republic 420 224 235 774, Denmark 45 45 76 26 00, Finland 385 (0) 9 725 72511,

France 33 (0) 1 48 14 24 24, Germany 49 89 7413130, India 91 80 41190000, Israel 972 3 6393737,

Italy 39 02 413091, Japan 81 3 5472 2970, Korea 82 02 3451 3400, Lebanon 961 (0) 1 33 28 28,

Malaysia 1800 887710, Mexico 01 800 010 0793, Netherlands 31 (0) 348 433 466,

New Zealand 0800 553 322, Norway 47 (0) 66 90 76 60, Poland 48 22 3390150,

Portugal 351 210 311 210, Russia 7 495 783 6851, Singapore 1800 226 5886,

Slovenia 386 3 425 42 00, South Africa 27 0 11 805 8197, Spain 34 91 640 0085,

Sweden 46 (0) 8 587 895 00, Switzerland 41 56 2005151, Taiwan 886 02 2377 2222,

Thailand 662 278 6777, Turkey 90 212 279 3031, United Kingdom 44 (0) 1635 523545

GS_NI_1411.fm Page 9 Wednesday, January 31, 2007 5:29 PM

National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation.

Refer to the Terms of Use section on ni.com/legal for more information about National

Instruments trademarks. Other product and company names mentioned herein are trademarks or trade

names of their respective companies. For patents covering National Instruments products, refer to the

appropriate location: Help»Patents in your software, the patents.txt file on your CD, or

ni.com/patents.

GS_NI_1411.fm Page 12 Wednesday, January 31, 2007 5:29 PM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere National Instruments PCI-Karte Handbücher

National Instruments

National Instruments RS-232 Bedienungsanleitung

National Instruments

National Instruments PCI-232/2 Bedienungsanleitung

National Instruments

National Instruments NI 6602 Bedienungsanleitung

National Instruments

National Instruments IMAQ PCI-1422 Bedienungsanleitung

National Instruments

National Instruments NI PXI/PCIe-8231 Bedienungsanleitung

National Instruments

National Instruments PCI-8361 Bedienungsanleitung

National Instruments

National Instruments PCIe-6593 Bedienungsanleitung

National Instruments

National Instruments IMAQ PCI-1408 Bedienungsanleitung

National Instruments

National Instruments Multisystem eXtension Interface NI PXI-8360 Bedienungsanleitung

National Instruments

National Instruments 6711 Bedienungsanleitung

National Instruments

National Instruments PCIe-5775 Bedienungsanleitung

National Instruments

National Instruments 6034E Bedienungsanleitung

National Instruments

National Instruments PCI-6509 Bedienungsanleitung

National Instruments

National Instruments NI PCIe-8360 Handbuch

National Instruments

National Instruments NI 9425 Bedienungsanleitung

National Instruments

National Instruments NI PCIe-8255R Bedienungsanleitung

National Instruments

National Instruments Vision PXI/PCI-1428 Bedienungsanleitung

National Instruments

National Instruments PXIe-8821 Bedienungsanleitung

National Instruments

National Instruments PXI-8231 Bedienungsanleitung

National Instruments

National Instruments NI 6731 Handbuch

National Instruments

National Instruments IMAQ PCI-1409 Bedienungsanleitung

National Instruments

National Instruments DAQ X Series Bedienungsanleitung

National Instruments

National Instruments PCI-GPIB Bedienungsanleitung

National Instruments

National Instruments PCI-FBUS Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung