NordicTrack FREESTRIDER 35 S Bedienungsanleitung

Model No. NTSR01909.1

Serial No.

Write the serial number in the space

above for reference.

USERʼS MANUA

Serial

Number

Decal

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Keep this manual

for future reference.

www.nordictrack.com

QUESTIONS?

f you have questions, or if parts are

damaged or missing, DO NOT

CONTACT THE STORE; please

contact Customer Care.

IMPORTANT: Please register this

product (see the limited warranty

on the back cover of this manual)

before contacting Customer Care.

CA TO -FREE:

1-888-825-2588

Mon.–Fri. 6 a.m.–6 p.m. MT

Sat. 8 a.m.–4 p.m. MT

ON THE WEB:

www.nordictrackservice.com

TAB E OF CONTENTS

WARNNGDECALPLACEMENT ..............................................................2

MPORTANTPRECAUTONS ................................................................3

BEFOREYOUBEGN ......................................................................4

ASSEMBLY ...............................................................................5

HOWTOUSETHECHESTPULSESENSOR...................................................11

HOWTOUSETHEELLPTCALSTRDER.....................................................12

MANTENANCEANDTROUBLESHOOTNG ...................................................20

EXERCSEGUDELNES ...................................................................21

PARTLST ..............................................................................23

EXPLODEDDRAWNG ....................................................................25

ORDERNGREPLACEMENTPARTS ..................................................BackCover

LMTEDWARRANTY ..............................................................BackCover

NordicTrack is a registered trademark of CON P, nc.

WARNING DECA P ACEMENT

This drawing shows the location(s) of the warning

decal(s). If a decal is missing or illegible, see

the front cover of this manual and request a

free replacement decal. Apply the decal in the

location shown. Note: The decal(s) may not be

shown at actual size.

WARNING: To reduce the risk of serious injury, read all important precautions and

instructions in this manual and all warnings on your elliptical strider before using your elliptical

strider. ICON assumes no responsibility for personal injury or property damage sustained by or

through the use of this product.

IMPORTANT PRECAUTIONS

1. Before beginning any exercise program,

consult your physician. This is especially

important for persons over age 35 or per-

sons with pre-existing health problems.

2. It is the responsibility of the owner to ensure

that all users of the elliptical strider are ade-

quately informed of all precautions.

3. The elliptical strider is intended for home

use only. Do not use the elliptical strider in a

commercial, rental, or institutional setting.

4. Keep the elliptical strider indoors, away from

moisture and dust. Place the elliptical strider

on a level surface, with a mat beneath it to

protect the floor or carpet. Make sure that

there is at least 3 ft. (1 m) of clearance in the

front and rear of your elliptical strider and 2

ft. (0.6 m) on each side.

5. Inspect and properly tighten all parts regu-

larly. Replace any worn parts immediately.

6. Keep children under age 12 and pets away

from the elliptical strider at all times.

7. The elliptical strider should not be used by

persons weighing more than 300 lbs.

(136 kg).

8. Wear appropriate exercise clothes while

using the elliptical strider. Always wear ath-

letic shoes for foot protection while exercis-

ing.

9. Hold the handlebars or the handrails when

mounting, dismounting, or using the ellipti-

cal strider.

10. The pulse sensor is not a medical device.

Various factors may affect the accuracy of

heart rate readings. The pulse sensor is

intended only as an exercise aid in determin-

ing heart rate trends in general.

11. Keep your back straight while using the

elliptical strider; do not arch your back.

12. Over exercising may result in serious injury

or death. If you feel faint or if you experience

pain while exercising, stop immediately and

cool down.

13. When you stop exercising, allow the pedals

to slowly come to a stop.

14. Use the elliptical strider only as described in

this manual.

BEFORE YOU BEGIN

Thank you for selecting the revolutionary

NordicTrack®FREESTR DER 35 S elliptical strider.

The FREESTR DER 35 S elliptical strider provides a

wide array of features designed to make your work-

outs more effective and enjoyable.

For your benefit, read this manual carefully before

you use the elliptical strider. f you have questions

after reading this manual, see the front cover of this

manual. To help us assist you, note the product num-

ber and serial number before contacting us. The

model number and the location of the serial number

decal are shown on the front cover of this manual.

Before reading further, please familiarize yourself with

the parts that are labeled in the drawing below.

Handrail

Wheel

Pedal

Console

Accessory Tray

Leveling Foot

Handlebar

Handgrip Pulse Sensor

Fan

ASSEMB Y

Assembly requires two persons. Place all parts of the elliptical strider in a cleared area and remove the pack-

ing materials. Do not dispose of the packing materials until assembly is completed.

In addition to the included tool(s), assembly requires a Phillips screwdriver .

As you assemble the elliptical strider, use the drawings below to identify small parts. The number in parentheses

below each drawing is the key number of the part, from the PART L ST near the end of this manual. The number

following the parentheses is the quantity needed for assembly. Note: Some small parts may have been pre-

assembled. If a part is not in the hardware kit, check to see if it has been preassembled.

3/8" x 1" Patch

Screw (122)–4

3/8" x 3/4" Patch

Screw (123)–2

3/8" x 3" Screw

(124)–2

1/4" x 3/4" Patch

Screw (127)–4

M10 Split

Washer (128)–2

#8 x 3/4"

Screw (86)–12

#8 x 1" Tek

Screw (126)–8

#8 x 35mm

Screw (125)–1

IMPORTANT: Do not remove the foam block

(not shown) located under the pedals until

you have completed step 2.

dentify the Shield Cap (5) and the Upright (26)

and orient them as shown. Slide the Shield Cap

upward around the Upright.

While another person holds the Upright (26)

near the Frame (1), locate the wire ties in the

Upright.

See the inset drawing. Tie the lower end of a

wire tie to the end of the Wire Harness (77).

Pull the other end of the wire tie upward out of

the top of the Upright (26).

Next, tie the lower end of the other wire tie to

the end of the Power Cable (81). Pull the other

end of the wire tie upward out of the top of the

Upright (26).

Then, untie and discard the wire ties.

Wire

Ties

Wire

Ties

2. Tip: Avoid pinching the wires. Attach the

Upright (26) to the Frame (1) with four 3/8" x 1"

Patch Screws (122). Note: Two of the Patch

Screws may be preattached to the Frame. Tip:

Start all the Patch Screws before tightening

any of them.

Remove and discard the foam block (not

shown) located under the pedals.

122

Avoid pinching

the wires

To make assembly easier, read the

information on page 5 before you begin.

3. Slide the Shield Cap (5) downward over the

Right and Left Shields (6, 7).

Attach the Shield Cap (5) with a #8 x 35mm

Screw (125) and two #8 x 3/4" Screws (86).

Tip: Start all the Screws before tightening

any of them.

125

4. Orient the Accessory Tray (18) as shown. Press

the Accessory Tray into the Shield Cap (5). 4

5. dentify the Right Handrail (69), which is marked

with a “Right” sticker.

While another person holds the Right Handrail

(69) near the Upright (26), connect the right

Pulse Wire (78) to the right Sensor Wire (79).

nsert the excess wire into the Right Handrail

(69). Then, slide the Right Handrail onto the

Upright (26).

Tip: Avoid pinching the wires. Attach the

Right Handrail (69) with a 3/8" x 3/4" Patch

Screw (123) and an M10 Split Washer (128).

Do not tighten the Patch Screw yet.

Repeat this step for the eft Handrail (70).

128

123

6. IMPORTANT: To prevent damage, do not

allow the elliptical strider to tip to either side

during this step.

While another person lifts the rear of the Frame

(1) in the location shown by the arrow, attach

each Handrail (69, 70) to the Frame with a 3/8"

x 3" Screw (124).

See step 5. Tighten the 3/8" x 3/4" Patch

Screws (123).

124

Avoid pinching

the wires

7. While another person holds the Console (4)

near the Upright (26), connect the console wires

to the Wire Harness (77), the Power Cable (81),

and the Ground Wire (82). Then, connect the

console pulse wires to the Pulse Wires (78).

nsert the excess wire downward into the

Upright (26).

Tip: Avoid pinching the wires. Attach the

Console (4) to the Upright (26) with four 1/4" x

3/4" Patch Screws (127).

127

81 82

Pulse

Wires

Console

Wires

8. dentify the Front and Rear Shields (10, 13) and

orient them as shown.

Attach the Front and Rear Shields (10, 13)

around the Upright (26) with six #8 x 3/4"

Screws (86).

Avoid pinching

the wires

9. dentify the Right Upper and Lower Covers (14,

15), which are marked with “Right” stickers, and

orient them as shown.

Attach the Right Upper and Lower Covers (14,

15) around the Right Handlebar (20) with two

#8 x 3/4" Screws (86).

Repeat this step for the eft Handlebar (21).

10. dentify a set of Right and Left Link Covers (22,

23), which are marked with “Right” and “Left”

stickers, and orient them as shown.

Attach the Right and Left Link Covers (22, 23)

around the Right Handlebar (20) with four #8 x

1" Tek Screws (126).

Repeat this step for the other side of the

elliptical strider.

126

11. Plug the AC power adapter into the jack on the front of the elliptical strider (see HOW TO PLUG N THE AC

POWER ADAPTER on page 12). IMPORTANT: If the elliptical strider has been exposed to cold temper-

atures, allow it to warm to room temperature before plugging in the AC power adapter. If you do not

do this, you may damage the console displays or other electronic components.

Make sure that all parts are properly tightened before you use the elliptical strider. Note: After assembly

is completed, some extra parts may be left over. Place a mat beneath the elliptical strider to protect the floor.

Andere Handbücher für FREESTRIDER 35 S

Inhaltsverzeichnis

Andere NordicTrack Ellipsentrainer Handbücher

NordicTrack

NordicTrack E5 si 831.23855.0 Bedienungsanleitung

NordicTrack

NordicTrack E 5.4 Bedienungsanleitung

NordicTrack

NordicTrack E 11.6 Elliptical Bedienungs- und Wartungshandbuch

NordicTrack

NordicTrack E4.1 Elliptical Bedienungs- und Wartungshandbuch

NordicTrack

NordicTrack E 11.5 Elliptical Bedienungsanleitung

NordicTrack

NordicTrack Asr 1000 Elliptical Bedienungsanleitung

NordicTrack

NordicTrack NTIVEL69016.0 Bedienungsanleitung

NordicTrack

NordicTrack 831.23948.1 Bedienungsanleitung

NordicTrack

NordicTrack 831.23949.2 Bedienungsanleitung

NordicTrack

NordicTrack NTEL00909.4 Bedienungsanleitung

NordicTrack

NordicTrack Cxt 950 Elliptical Kurzanleitung

NordicTrack

NordicTrack Cxt 1400 Elliptical Bedienungsanleitung

NordicTrack

NordicTrack Elliptical E7.1 Bedienungsanleitung

NordicTrack

NordicTrack NTEL05011.4 Bedienungsanleitung

NordicTrack

NordicTrack E9 Zl Elliptical Bedienungsanleitung

NordicTrack

NordicTrack Elite 10.7 Elliptical Bedienungsanleitung

NordicTrack

NordicTrack VGR 850 Bedienungsanleitung

NordicTrack

NordicTrack COMMERCIAL 12.9 Bedienungsanleitung

NordicTrack

NordicTrack FREESTRIDE Bedienungsanleitung

NordicTrack

NordicTrack NTEL59012 Bedienungsanleitung

NordicTrack

NordicTrack NTEL05011.6 Bedienungsanleitung

NordicTrack

NordicTrack CXT 980 Bedienungsanleitung

NordicTrack

NordicTrack CX 938 elliptical exerciser 30621.0 Bedienungsanleitung

NordicTrack

NordicTrack Elite 11.0 NTEVEL99915.0 Bedienungsanleitung

Beliebte Ellipsentrainer Handbücher anderer Marken

Weslo

Weslo Momentum 4.0 Elliptical Bedienungs- und Wartungshandbuch

Progear Fitness

Progear Fitness Air elliptical pro 1307 Bedienungsanleitung

Torque Fitness

Torque Fitness XPLLP Bedienungsanleitung

Octane Fitness

Octane Fitness PRO3700C Bedienungsanleitung

Xterra

Xterra FS5.8e Bedienungsanleitung

Bodyguard

Bodyguard E-40 Bedienungsanleitung

Bonn Germany

Bonn Germany Concept 2.2 Bedienungsanleitung

Precor

Precor Resolute RSL 620 Bedienungsanleitung

Vision Fitness

Vision Fitness X6600iNetTV Bedienungsanleitung

Matrix

Matrix MX-A5x Bedienungsanleitung

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 Bedienungsanleitung

Sears

Sears FREE SPIRIT C249 30737 0 Bedienungsanleitung

True

True FS-64 Bedienungsanleitung

Sport-thieme

Sport-thieme ST 310 Bedienungsanleitung

VIRTUFIT

VIRTUFIT CTR 1.1 Bedienungsanleitung

Kettler

Kettler GIRO C 1 Bedienungsanleitung

CIRCLE FITNESS

CIRCLE FITNESS E7 Bedienungsanleitung

Reebok

Reebok 1000 Zx Elliptical Bedienungsanleitung