NordicTrack NTEL7906.4 Bedienungsanleitung

Serial Number

Decal

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Keep this manual

for future reference.

QUESTIONS?

If you have questions, or if parts are

damaged or missing, DO NOT

CONTACT THE STORE; please

contact Customer Care.

IMPORTANT: You must note the

product model number and serial

number (see the drawing above)

before contacting us:

CA TO -FREE:

1-888-825-2588

Mon.–Fri. 6 a.m.–6 p.m. MT

Sat. 8 a.m.–4 p.m. MT

ON THE WEB:

www.nordictrackservice.com

www.nordictrack.com

Model No. NTE 7906.4

Serial No.

Write the serial number in the

space above for reference.

USERʼS MANUA

TAB E OF CONTENTS

WARNINGDECALPLACEMENT ..............................................................2

IMPORTANTPRECAUTIONS ................................................................3

BEFOREYOUBEGIN ......................................................................4

ASSEMBLY ...............................................................................5

HOWTOUSETHEELLIPTICALEXERCISER ..................................................11

MAINTENANCEANDTROUBLESHOOTING ...................................................22

EXERCISEGUIDELINES ...................................................................23

PARTLIST ..............................................................................24

EXPLODEDDRAWING ....................................................................26

ORDERINGREPLACEMENTPARTS ..................................................BackCover

LIMITEDWARRANTY ..............................................................BackCover

NordicTrack is a registered trademark of ICON IP, Inc.

WARNING DECA P ACEMENT

This drawing shows the location(s) of the

warning decal(s). If a decal is missing or

illegible, see the front cover of this

manual and request a free replacement

decal. Apply the decal in the location

shown. Note: The decal(s) may not be

shown at actual size.

WARNING: To reduce the risk of serious injury, read all important precautions and

instructions in this manual and all warnings on your elliptical exerciser before using your elliptical

exerciser. ICON assumes no responsibility for personal injury or property damage sustained by or

through the use of this product.

IMPORTANT PRECAUTIONS

1. Before beginning any exercise program,

consult your physician. This is especially

important for persons over the age of 35 or

persons with pre-existing health problems.

2. It is the responsibility of the owner to ensure

that all users of the elliptical exerciser are

adequately informed of all precautions.

3. Your elliptical exerciser is intended for home

use only. Do not use your elliptical exerciser

in a commercial, rental, or institutional set-

ting.

4. Keep your elliptical exerciser indoors, away

from moisture and dust. Place your elliptical

exerciser on a level surface, with a mat

beneath it to protect the floor or carpet.

Make sure that there is at least 3 ft. (0.9 m) of

clearance in the front and rear of your ellipti-

cal exerciser and 2 ft. (0.6 m) on each side.

5. Inspect and properly tighten all parts regu-

larly. Replace any worn parts immediately.

6. Keep children under age 12 and pets away

from your elliptical exerciser at all times.

7. Your elliptical exerciser should not be used

by persons weighing more than 325 lbs.

(147 kg).

8. Wear appropriate exercise clothes while

exercising; do not wear loose clothes that

could become caught on your elliptical exer-

ciser. Always wear athletic shoes for foot

protection while exercising.

9. Hold the handgrip pulse sensor or the upper

body arms when mounting, dismounting, or

using your elliptical exerciser.

10. Keep your back straight while using your

elliptical exerciser; do not arch your back.

11. The pulse sensor is not a medical device.

Various factors, including the userʼs move-

ment, may affect the accuracy of heart rate

readings. The pulse sensor is intended only

as an exercise aid in determining heart rate

trends in general.

12. When you stop exercising, allow the pedals

to slowly come to a stop.

13. If you feel pain or dizziness while exercising,

stop immediately and cool down.

14. Use your elliptical exerciser only as

described in this manual.

BEFORE YOU BEGIN

Thank you for selecting the revolutionary

NordicTrack®AUDIOSTRIDER 990 elliptical exerciser.

The AUDIOSTRIDER 990 elliptical exerciser provides

an impressive selection of features designed to make

your workouts at home more effective and enjoyable—

and when youʼre not exercising, the unique elliptical

exerciser can be folded out of the way.

For your benefit, read this manual carefully before

you use the elliptical exerciser. If you have ques-

tions after reading this manual, please see the front

cover of this manual. To help us assist you, note the

product model number and serial number before con-

tacting us. The model number and the location of the

serial number decal are shown on the front cover of

this manual.

Before reading further, please familiarize yourself with

the parts that are labeled in the drawing below.

Pulse Sensor

Audio Cable

Upper Body Arm

Pedal Disc

Wheel

Pedal

Speakers

Water Bottle Holder*

Console

Leveling Foot

Handle Power Socket

Latch Button

Ramp

Storage Magnet

Fan

Pedal Arm Latch

*Water bottle is not included

Leveling Foot

ASSEMB Y

Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the

packing materials. Do not dispose of the packing materials until assembly is completed.

In addition to the included tools, assembly requires a Phillips screwdriver and rubber

mallet .

As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parenthe-

ses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The

number following the parentheses is the quantity needed for assembly. Note: Some small parts may have

been preassembled. If a part is not in the hardware kit, check to see if it has been preassembled.

M10 x 93mm Button Screw (82)–4

M10 x 25mm

Washer (87)–2

M8 Split

Washer (101)–4

M4 x 16mm

Screw (116)–16

M6 Split Washer

(102)–8

M6 x 35mm

Screw (109)–4

M6 x 62mm

Screw (108)–4

M8.5 x 16mm x

1.5mm Washer

(103)–6

Link Arm

Spacer (74)–4

M8 x 20mm Button

Screw (107)–4

M8 x 25mm Button

Screw (110)–2

M10 x 20mm Button

Screw (111)–2

M8 x 15mm Button

Screw (106)–10

M10 Curved

Washer (99)–4

Wave Washer

(100)–2

1. If there is a shipping bracket attached to the

rear of the Folding Frame (not shown), remove

the screw and the shipping bracket from the

Folding Frame. Discard the screw and the ship-

ping bracket.

See HOW TO FO D AND UNFO D THE

E IPTICA EXERCISER on page 11 and

unfold the elliptical exerciser.

While another person lifts the front of the

Frame (1), attach the Front Stabilizer (4) to the

Frame with two M10 x 93mm Button Screws

(82) and two M10 Curved Washers (99).

82 1

2. While another person lifts the Folding Frame

(2), attach the Rear Stabilizer (3) to the Folding

Frame with two M10 x 93mm Button Screws

(82) and two M10 Curved Washers (99). Next,

tighten the Center Foot (95) into the Frame (1).

3. Attach the Front Ramp Cover (6) to the

Ramp (5) with four M4 x 16mm Screws (116).

Slide an M10 x 25mm Washer (87) onto an

M10 x 20mm Button Screw (111). Tighten the

Button Screw into one end of the Ramp

Axle (72). Apply a small amount of the included

grease to the Ramp Axle.

Orient the Ramp (5) as shown. Make sure that

the post on the Frame (1) is in the center of

the Ramp. Align the lower end of the Ramp

with the welded tube on the Frame. Insert the

Ramp Axle (72) into the Ramp and the welded

tube.

Slide an M10 x 25mm Washer (87) onto an

M10 x 20mm Button Screw (111). Tighten the

Button Screw into the open end of the Ramp

Axle (72).

Grease

111

116

111

5. Insert the Roller (38) on the Left Pedal Arm (32)

and the Roller (not shown) on the Right Pedal

Arm (33) into the sides of the Ramp (5).

Attach the Rear Ramp Cover (7) to the

Ramp (5) with two M4 x 16mm Screws (116).

See the inset drawing. Lift the Pedal Arm

Latch (41) on the Left Pedal Arm (32) and set

the end of the Left Pedal Arm on the left Crank

Bushing Sleeve (54). Release the Pedal Arm

Latch; make sure that the Left Pedal Arm is

securely connected to the Crank Bushing

Sleeve.

Connect the Right Pedal Arm (33) to the

right Crank Bushing Sleeve (not shown) in

the same way.

4. Identify the Left Pedal (34) and the Left Pedal

Arm (32), which are marked with stickers.

Attach the Left Pedal (34) to the Left Pedal

Arm (32) with two M6 x 62mm Screws (108),

two M6 x 35mm Screws (109), and four M6

Split Washers (102).

Attach the Right Pedal (not shown) to the

Right Pedal Arm (not shown) in the same

way.

116

108

102

109

102

7. Attach the Left Upper Body Arm (22) to the left

Upper Body Leg (24) with three M8 x 15mm

Button Screws (106).

Attach the Right Upper Body Arm (23) in the

same way.

6. While another person holds the Upright (10)

near the Frame (1), connect the ends of the

Upper Wire Harness (65) to the Lower Wire

Harness (64).

Carefully insert the Upright (10) into the

Frame (1); be careful not to damage the Wire

Harnesses (64, 65). Attach the Upright with

four M8 x 20mm Button Screws (107) and four

M8 Split Washers (101).

106

107

101 101

Be careful not

to damage the

Wire Harnesses

(64, 65) during

this step

107

9. Apply a small amount of grease to the axle on

the Left Link Arm (30), to the axle on the Left

Pedal Arm (32), and to a Wave Washer (100).

Slide the Wave Washer (100) onto the axle on

the Left Pedal Arm (32). Next, slide a Link Arm

Spacer (74) onto the axle on the Left Link

Arm (30).

Then, insert the axle on the Left Link Arm (30)

into the left Upper Body Leg (24) while sliding

the Left Link Arm onto the axle on the Left

Pedal Arm (32).

Repeat this step with the Right ink

Arm (31).

100

Grease

8. Hold the Left Rear Upper Body Cover (26) and

the Left Front Upper Body Cover (27) around

the left Upper Body Leg (24). Attach the Upper

Body Covers with five M4 x 16mm Screws

(116).

Attach the Right Rear Upper Body Cover

(28) and the Right Front Upper Body Cover

(29) in the same way.

116

10. Attach the Left Link Arm (30) to the Left Pedal

Arm (32) with an M8 x 15mm Button Screw

(106), an M8.5 x 16mm x 1.5mm Washer (103),

and an Axle Cover (66).

Attach the Left Link Arm (30) to the left Upper

Body Leg (24) with an M8 x 25mm Button

Screw (110), two M8.5 x 16mm x 1.5mm

Washers (103), two Axle Covers (66), a Link

Arm Spacer (74), and an M8 x 15mm Button

Screw (106) as shown.

Attach the Right ink Arm (31) in the same

way.

11. Plug the power cord into the power socket at the rear of the elliptical exerciser (see HOW TO PLUG IN THE

POWER CORD on page 11). IMPORTANT: If the elliptical exerciser has been exposed to cold tempera-

tures, allow it to warm to room temperature before plugging in the power cord. If you do not do this,

the console displays or other electronic components may become damaged.

Make sure that all parts of the elliptical exerciser are properly tightened. Note: Some hardware may be

left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the

elliptical exerciser.

66 74

103

110

103

106

103

106

Dieses Handbuch passt für folgende Modelle

Andere NordicTrack Ellipsentrainer Handbücher

NordicTrack

NordicTrack E4.0 Elliptical Systemhandbuch

NordicTrack

NordicTrack NTCCEL16907.0 Bedienungsanleitung

NordicTrack

NordicTrack NTCW90907.0 Bedienungsanleitung

NordicTrack

NordicTrack Audiostrider Cx650 Elliptical Benutzerhandbuch

NordicTrack

NordicTrack E11.0 Elliptical Bedienungsanleitung

NordicTrack

NordicTrack NTEL00907.0 Bedienungsanleitung

NordicTrack

NordicTrack E9.2 NTEVEL99812.0 Bedienungsanleitung

NordicTrack

NordicTrack Cxt 950 Elliptical Bedienungsanleitung

NordicTrack

NordicTrack C 1750 Pro Treadmill Bedienungsanleitung

NordicTrack

NordicTrack E11.0 Elliptical Benutzerhandbuch

NordicTrack

NordicTrack NTEL09109.7 Bedienungsanleitung

NordicTrack

NordicTrack E 7.2 Elliptical Kurzanleitung

NordicTrack

NordicTrack E11.0 Elliptical Einrichtungshandbuch

NordicTrack

NordicTrack CX 938 NEL5095.1 Bedienungsanleitung

NordicTrack

NordicTrack E4.1 Elliptical Bedienungs- und Wartungshandbuch

NordicTrack

NordicTrack E4.2 Elliptical Einrichtungshandbuch

NordicTrack

NordicTrack E 11.6 Elliptical Bedienungs- und Wartungshandbuch

NordicTrack

NordicTrack E11.0 Elliptical Bedienungs- und Wartungshandbuch

NordicTrack

NordicTrack NTEVEL89816.0 Bedienungsanleitung

NordicTrack

NordicTrack E 1000 Elliptical Bedienungsanleitung

NordicTrack

NordicTrack E7 Rear Drive Elliptical Kurzanleitung

NordicTrack

NordicTrack E4.0 Elliptical Bedienungs- und Wartungshandbuch

NordicTrack

NordicTrack Smart Terrain 12.0 NTEL01310.3 Bedienungsanleitung

NordicTrack

NordicTrack NEL09940 Bedienungsanleitung

Beliebte Ellipsentrainer Handbücher anderer Marken

Weslo

Weslo Momentum 4.0 Elliptical Bedienungs- und Wartungshandbuch

Progear Fitness

Progear Fitness Air elliptical pro 1307 Bedienungsanleitung

Torque Fitness

Torque Fitness XPLLP Bedienungsanleitung

Octane Fitness

Octane Fitness PRO3700C Bedienungsanleitung

Xterra

Xterra FS5.8e Bedienungsanleitung

Bodyguard

Bodyguard E-40 Bedienungsanleitung

Bonn Germany

Bonn Germany Concept 2.2 Bedienungsanleitung

Precor

Precor Resolute RSL 620 Bedienungsanleitung

Vision Fitness

Vision Fitness X6600iNetTV Bedienungsanleitung

Matrix

Matrix MX-A5x Bedienungsanleitung

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 Bedienungsanleitung

Sears

Sears FREE SPIRIT C249 30737 0 Bedienungsanleitung

True

True FS-64 Bedienungsanleitung

Sport-thieme

Sport-thieme ST 310 Bedienungsanleitung

VIRTUFIT

VIRTUFIT CTR 1.1 Bedienungsanleitung

Kettler

Kettler GIRO C 1 Bedienungsanleitung

CIRCLE FITNESS

CIRCLE FITNESS E7 Bedienungsanleitung

Reebok

Reebok 1000 Zx Elliptical Bedienungsanleitung