Olympus BX3M-CB Bedienungsanleitung

INSTRUCTIONS

This instruction manual is for the control box or FM control box.

To ensure the safety, obtain optimum performance and to familiarize yourself fully with

the use of this product, we recommend that you study this manual thoroughly before

operating this product, and always keep this manual at hand when operating this product.

Retain this instruction manual in an easily accessible place near the work desk for future

reference.

Control box/FM Control box

BX3M-CB/CBFM

BX3M-CB

BX3M-CBFM

BX3M-HS

BX3M-HSRE

U-MIXR

Optical Microscope Accessory

In accordance with European Directive on Waste Electrical and Electronic Equipment, this symbol indicates that the

product must not be disposed of as unsorted municipal waste, but should be collected separately.

Refer to your local Olympus distributor in EU for return and/or collection systems available in your country.

NOTE: This product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated

in a commercial environment. This product generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this product in a residential area is likely to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the product.

This product is a part of the system product which complies with the CE marking.

Please refer to the instruction manual of your system product for the safety instructions related to the CE marking.

For Korea only

이 기기는 업무용 환경에서 사용할 목적으로 적합성평가를 받은 기기로서 가정용

환경에서 사용하는 경우 전파간섭의 우려가 있습니다.

Introduction............................................................................................................................................................................1

Safety precautions...........................................................................................................................................................2

1 Nomenclature of respective portions........................................................................................................7

2 Operation procedures.............................................................................................................................................9

2-1 Turning ON the main switch (BX3M-CBFM only)................................................................................................9

2-2 Operating the MIX slider for reflected light observation...............................................................................10

1Inserting the MIX slider for reflected light observation............................................................................................................10

2Turning ON the illumination of the MIX slider for reflected light observation...................................11

3Adjusting the brightness..................................................................................................................................................................12

4Selecting the illumination pattern............................................................................................................................................13

2-3 Operating the motorized nosepiece..............................................................................................................................15

3 Specifications..................................................................................................................................................................16

4 Troubleshooting............................................................................................................................................................17

5 Assembly.............................................................................................................................................................................27

5-1 Assembly procedures (BX3M-CBFM only) ...............................................................................................................27

5-2 Connection with PC......................................................................................................................................................................30

5-3 Setting the dip switch..................................................................................................................................................................33

6 Proper selection of the power supply cord ........................................................................................34

Table of Contents

BX3M-CB/CBFM

Contents of instruction manuals

This instruction manual is for control box BX3M-CB and BX3M-CBFM. For usage in combination with microscope, refer

to the instruction manual for your microscope.

The control box BX3M-CB and BX3M-CBFM are used to control motorized revolving nosepiece, MIX slider for reflected

light observation and so on installed on the microscope.

Introduction

If the product is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition, the

product may also be damaged. Always use the product according to this instruction manual.

The following symbols are used in this instruction manual.

CAUTION : Indicates a potentially hazardous situation which, if not avoided, may result in

minor or moderate injury.

NOTE

: Indicates a potentially hazardous situation which, if not avoided, may result in

damage to the product or other property.

TIP

: Indicates the useful knowledge or information for use.

CAUTION - Installation of the product -

Install the product on a sturdy, level table or bench. (BX3M-CBFM)

If you install the product on an unstable table or a tilted table, the product may drop and you may get injured.

Attach the product securely to the back surface of the microscope. (BX3M-CB)

For installation procedure, refer to the instruction manual for system microscope BX53M.

Safety precautions

BX3M-CB/CBFM

CAUTION - Electric safety -

Always use the power cord provided by Olympus.

If the proper AC adapter and the power cord is not used, the electric safety and the EMC (Electro-Magnetic

Compatibility) performance of the product cannot be assured.

If no power cord is provided, please select the proper power cord by referring to the section “Proper selection of the

power supply cord” at the end of this instruction manual.

Always connect the ground terminal.

Connect the ground terminal of the power cord and that of the power outlet. If the product is not grounded, our

intended electric safety and EMC performance of the product can not be assured.

Do not use the product in close proximity to the sources of strong electromagnetic radiation.

Proper operation may be interfered. The electromagnetic environment should be evaluated prior to operation of the

product.

Remove the power cord in case of emergency.

In case of emergency, be sure to unplug the power cord from the power cord connector on the product or from the

wall power outlet. Install the product at the location where you can reach the power cord connector or the wall power

outlet at hand to remove the power cord quickly.

CAUTION - Protection of electrick shock -

Keep the power cord and cables sufficiently away from the lamp housing.

If the power cord and cables contact a hot area of the lamp housing, they could melt and cause electric shock.

CAUTION - Protection for injury -

Do not pull the cable with an excessive force.

If you pull the cable connected to the control box with an excessive force, the control box may drop and you may get

injured.

The following symbols are placed on the product.

Study the meaning of the symbols and always use the product in the safest possible manner.

Symbol Meaning

Indicates a non-specific general hazard. Follow the cautions given after this symbol

or in the instruction manual.

Indicates that the main switch is ON. (BX3M-CBFM only)

Indicates that the main switch is OFF. (BX3M-CBFM only)

When caution labels are dirty or peeled off, contact Olympus for replacement or inquiries.

CAUTION - Safety symbols -

BX3M-CB/CBFM

CAUTION - LED (light emitting diode) -

Do not look directly at the light from the LED light source for a long time.

The LED built in the MIX slider for reflected light observation (U-MIXR) (separately available) is basically eye-safe. However,

do not look directly at the light from the LED lamp house for a long time, since it may cause damage to your eyes.

If the laws or regulations for workers health and safety have been established, follow them when using the

microscope.

Do not look directly at the light coming out from the objective or the specular reflection light from the

specimen.

Do not look directly at the light coming out from the objective for a long time, since it may cause damage to your eyes.

Do not expose your skin to the light coming out from the objective for a long time.

If your skin is exposed to the light coming out from the objective for a long time, you may get burned.

Do not press the micro switch of the MIX slider for reflected

light observation (U-MIXR) with your finger.

If you press the micro switch aof the MIX slider for reflected light

observation with your finger, the MIX slider for reflected light observation

may emit the light.

Do not insert the MIX slider for reflected light observation

(U-MIXR) upside down.

Do not insert the MIX slider for reflected light observation upside down.

Otherwise, the light coming out from the MIX slider for reflected light

observation enters your eyes through the eyepiece and your eyes may

be damaged.

aDo not press with your finger.

Handling precautions

1. Wipe the portions with a dry soft cloth.

If the dirt cannot be removed by dry-wiping, moisten a soft cloth with diluted neutral detergent and wipe the dirty

surface with it.

Do not use the organic solvents because they may deteriorate the coated surface or plastic parts.

2. Before disposing of this product, be sure to follow the regulations and rules of your local government.

NOTE

Maintenance and storage

·This product is a precision instrument. Handle it with care and avoid subjecting it to a sudden or severe

impact.

·Never disassemble any part of the product. Otherwise, failure could be caused.

·Do not use this product in areas where it may be subjected to direct sunlight, high temperature and/or

humidity, dust or vibrations.

(For the conditions of operating environments, see “3 Specifications” (page 16).)

·Before attaching or detaching the units other than the MIX slider for reflected light observation (U-MIXR),

turn the power of product (OFF) as follows:

·(BX3M-CB) set the main switch of the microscope to (OFF).

·(BX3M-CBFM) set the main switch of the controll box to (OFF).

NOTE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Olympus Mikroskop Handbücher

Olympus

Olympus Fluoview FV1000 Bedienungsanleitung

Olympus

Olympus ORBEYE Handbuch

Olympus

Olympus FH Bedienungsanleitung

Olympus

Olympus BX51-P Betriebsanleitung

Olympus

Olympus SZ2-ILA Bedienungsanleitung

Olympus

Olympus SZX2-LTTR Bedienungsanleitung

Olympus

Olympus CX43 Bedienungsanleitung

Olympus

Olympus BX41 Bedienungsanleitung

Olympus

Olympus BX61WI Bedienungsanleitung

Olympus

Olympus CK40M FRAME Betriebsanleitung

Olympus

Olympus BHTP Bedienungsanleitung

Olympus

Olympus SZ-III Bedienungsanleitung

Olympus

Olympus CX41 Bedienungsanleitung

Olympus

Olympus BX51 Bedienungsanleitung

Olympus

Olympus FV5-LD405 Bedienungsanleitung

Olympus

Olympus BX51M Bedienungsanleitung

Olympus

Olympus BHA-P Bedienungsanleitung

Olympus

Olympus BHTU-112 Bedienungsanleitung

Olympus

Olympus BH2 Series Betriebsanleitung

Olympus

Olympus SZX-AR1 Bedienungsanleitung

Olympus

Olympus BH2 Series Leitfaden

Olympus

Olympus Fluoview FV1000 Handbuch

Olympus

Olympus BX60 Bedienungsanleitung

Olympus

Olympus VM Series Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Leica

Leica FL560 Bedienungsanleitung