Olympus CX21 Bedienungsanleitung

INSTRUCTIONS

CX21

EDUCATION MICROSCOPE

A X 7 4 0 3

This instruction manual is for the Olympus Education Microscopes Model CX21. To ensure the

safety, obtain optimum performance and to familiarize yourself fully with the use of this microscope,

we recommend that you study this manual thoroughly before operating the microscope. Retain this

instruction manual in an easily accessible place near the work desk for future reference.

CX21

CONTENTS

7-11

IMPORTANT — Be sure to read this section for safe use of the equipment. —

1 STANDARD COMPONENT UNITS

2 NOMENCLATURE

4 DETAILED OBSERVATION PROCEDURE

SUMMARY OF BRIGHTFIELD OBSERVATION PROCEDURE

1-3

10-1 System Diagram of Optional Accessories ............................................................................ 19

10-2 Installation and Operation of Optional Accessories ..................................... 19-21

1Turning the Lamp ON ........................................... 7

3Adjusting the Focus ................................................ 8

5Adjusting the Diopter ............................................ 9

Placing Specimen on the Stage

.................... 7

Adjusting the Interpupillary Distance

..................... 9

5 ONE-POINT ADVICE

6 TROUBLESHOOTING GUIDE

7 SPECIFICATIONS

8 OPTICAL CHARACTERISTICS

9 ASSEMBLY

10 OPTIONAL ACCESSORIES

13-14

17- 18

19-21

1Cord Hanger CH3-CH ............................................................................................................................................................................................ 19

2Filter Holder CH2-FH ............................................................................................................................................................................................... 20

3Darkfield Ring CH2-DS ........................................................................................................................................................................................ 20

4Reflection Mirror CH20-MM .......................................................................................................................................................................... 20

5Eyepieces WHC15X/WHC15X-H

..............................................................................................................................................................................................

6Using the eyepiece micrometer

...............................................................................................................................................................................................

6Adjusting the Condenser Position and Aperture Iris Diaphragm ............................................................. 10

7Switching the Objectives ............................ 10 8

Using the 100X Immersion Objective ....................

PROPER SELECTION OF THE POWER SUPPLY CORD....................................................... 22-23

IMPORTANT

SAFETY PRECAUTIONS

1. After the equipment has been used in an observation of a specimen

that is accompanied with a potential of infection, clean the parts

coming in contact with the specimen to prevent infection.

· Moving this product is accompanied with the risk of dropping the

specimen. Be sure to remove the specimen before moving this prod-

uct.

· In case the specimen is damaged by erroneous operation, promptly

take the infection prevention measures.

2. To avoid potential shock hazards and burns when replacing the lamp

bulb, set the main switch 1 to “ ” (OFF) then disconnect the power cord

from the wall outlet in advance. Whenever you replace the bulb during

use or right after use, allow the lamp socket 2 and bulb to cool before

touching. (Fig. 1)

Applicable lamp bulb: 6V20WHAL halogen bulb (Philips Type 7388)

3. Install the microscope on a sturdy, level table or bench so as not to block

the air vents on the underside of the base.

Do not place the microscope on a flexible surface, as this could result in

blocking the air vents and cause overheating or a fire.

4. Always use the power cord provided by Olympus. If no power cord is

provided, please select the proper power cord by referring to the section

“PROPER SELECTION OF THE POWER SUPPLY CORD” at the end of

this instruction manual. If the proper power cord is not used, product

safety performance cannot be warranted.

5. When installing the microscope, route the power cord away from the

microscope frame. Should the power cord come in contact with a hot

part, the power cord could melt and cause electric shock.

6. Always ensure that the grounding terminal of the microscope and that

of the wall outlet are properly connected. If the equipment is not grounded,

Olympus can no longer warrant the electrical safety performance of the

equipment.

7. Never allow metallic objects penetrate into the air vents of the micro-

scope frame as this could result in electrical shock, personal injury and

equipment damage.

8. After operation or in case of abnormality, be sure to disconnect the power

cord from the connector on the microscope or from the wall power outlet.

Fig. 1

Safety Symbols

The following symbols are found on the microscope. Study the meaning of the symbols and always use the equipment

in the safest possible manner.

Symbol Explanation

Indicates that the surface becomes hot, and should not be touched with bare hands.

Indicates that the main switch is ON.

Indicates that the main switch is OFF.

Before use, carefully read the instruction manual. Improper use could result in personal injury to

the user and/or damage to the equipment.

CX21

Warning Label

A warning indication label is attached to every part where special precaution is required when handling and using the

microscope. Always heed the warnings.

Warning label

position

Bottom of microscope

frame

[Warning against high temperature in

lamp bulb replacement]

If the warning label is stained or peeled off, contact Olympus.

1Getting Ready

1. A microscope is a precision instrument. Handle it with care and avoid

subjecting it to sudden or severe impact.

2. Do not use the microscope where it is subjected to direct sunlight,

high temperature and humidity, dust or vibrations. (For the operating

conditions, see chapter 7, “SPECIFICATIONS” on Page 15.)

3. Always use the tension adjustment ring to adjust the rotation tension of

the coarse adjustment knob.

4. The microscope is ventilated by natural convection. Be sure to leave

enough spaces (10 cm or more) around it when installing it.

5. When carrying the microscope, hold both sides around the hole of the

arm as shown in Fig. 2 and carry carefully.

# To prevent damage, do not hold the microscope by the stage 1or

observation tube 2.

Be sure to remove the specimen; otherwise, it may fall.

Fig. 2

2Maintenance and Storage

1. To clean the lenses and other glass components, simply blow dirty away using a commercially available blower and wipe

gently using a piece of cleaning paper (or clean gauze).

If a lens is stained with fingerprints or oil smudges, wipe it gauze slightly moistened with commercially available absolute

alcohol.

Since the absolute alcohol is highly flammable, it must be handled carefully.

Be sure to keep it away from open flames or potential sources of electrical sparks –– for example, electrical

equipment that is being switched on or off.

Also remember to always use it only in a well-ventilated room.

2. Do not attempt to use organic solvents to clean the microscope components other than the glass components. To clean

them, use a lint-free, soft cloth slightly moistened with a diluted neutral detergent.

3. Do not disassemble any part of the microscope as this could result in malfunction or reduced performance.

4. When not using the microscope, ensure that the frame is cooled down and store it in a dry locker or cover it with a dust

cover.

Fig. 3

5. To clean the condenser, fully loosen the securing knob 1, then remove

the condenser by lowering it with the condenser height adjustment knob

2, and wipe the front lens of the condenser.

The condenser can be attached by reversing the above removal

procedure.

6. When disposing of the microscope. Check the regulations and rules

of your local government and be sure to observe them.

3 Caution

If the microscope is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition,

the equipment may also be damaged. Always use the equipment as outlined in this instruction manual.

The following symbols are used to set off text in this instruction manual.

: Indicates that failure to follow the instructions in the warning could result in bodily harm to the

user and/or damage to equipment (including objects in the vicinity of the equipment).

# : Indicates that failure to follow the instructions could result in damage to equipment.

} : Indicates commentary (for ease of operation and maintenance).

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with the requirements of directive 98/79/EC concerning in vitro diag-

nostic medical devices. CE marking means the conformity to the directive.

4Intended use

This instrument has been designed to be used to observe magnified images of specimens in routine and research

applications.

Do not use this instrument for any purpose other than its intended use.

CX21

STANDARD COMPONENT UNITS

}After opening the package, make sure that the correct component units for the selected set are present.

· The differences between the CX21FS1 and CX21FS2 lie in the number of objectives and presence of immersion oil.

# The objectives have been screwed in tightly to prevent them from being loosened during transportation. To

remove an objective, turn it counterclockwise while holding it with a rubber sheet, etc., so that your fingers don’t slip.

Eyepieces

(Fixed at 10X)

Stage

Condenser

Binocular observation

tube

Revolving nosepiece

Microscope frame

Objectives

· 4X, 10X, 40X, 100X

(CX21FS1)

· 4X, 10X, 40X

(CX21FS2)

6V20WHAL halogen bulb Immersion oil

· Provided with a set including

the 100X objective.

Daylight (blue) filter

Optional Accessories

· Cord Hanger

CH3-CH

· Filter Holder

CH2-FH

· Reflection Mirror

CH20-MM

· Eyepieces

WHC15X

WHC15X-H

· Darkfield Ring

CH2-DS

“ ”: Power ON

“ ”: Power OFF

NOMENCLATURE

}The following items have been attached at the factory to prevent deterioration during transport. Remove these items and

retain them for future use. Then loosen the observation tube clamping knob and correct the orientation of the eyepieces

as shown in the illustration below.

1 Revolving nosepiece/observation tube transport band

2 Stage and specimen holder protection sheet

3 Protective pad below the stage

}Attach the lamp bulb and power cord as described in chapter 9, “ASSEMBLY” on pages 17-18.

Diopter adjustment ring

(Page 9)

}For detailed description of each control, refer to the page indicated inside parentheses.

Specimen holder (Page 7)

Aperture iris diaphragm ring

(Page 10)

Filter holder (Page 20)

Light intensity adjustment

knob (Page 7)

Revolving nosepiece

(Page 10)

Observation tube clamping

knob

Pre-focusing knob (Page 9)

Specimen holder Y-axis

feed knob (Page 7)

Specimen holder X-axis

feed knob (Page 7)

Fine adjustment

knob (Page 8)

Coarse adjustment

knob (Page 8)

Main switch (Page 7)

CX21

SUMMARY OF BRIGHTFIELD OBSERVATION PROCEDURE

Set the main switch to “ I" (ON) and adjust

the brightness.

1Main switch (P. 7)

2Light intensity adjustment knob (P. 7)

Place the specimen on the stage. 3Specimen holder (P. 7)

4X-axis/Y-axis feed knobs (P. 7)

Engage the 10X objective in the light path. 5Revolving nosepiece (P. 10)

Bring the specimen in focus 6Coarse/fine focus adjustment knobs (P. 8)

Adjust the interpupillary distance.

Adjust the diopter.

7Binocular tube (P. 9)

8Diopter adjustment ring (P. 9)

Adjust the aperture iris diaphragm. 9Aperture iris diaphragm ring (P. 10)

Engage the objective to be used in the light

path and bring the specimen in focus.

aFilters (Diameter: 32.5 mm or 45 mm) (P. 20)

Engage the required filters.

5Revolving nosepiece (P. 10)

6Coarse/fine adjustment knobs (P. 8)

Adjust the brightness. 2Light intensity adjustment knob (P. 7)

Start observation.

(Controls Used) (Page)

Fig. 4

DETAILED OBSERVATION PROCEDURE

1Turning the Lamp ON (Fig. 4)

1. Set the main switch 1to “ I” (ON).

2. Rotating the light intensity adjustment knob 2in the direction of the

arrow increases brightness and rotating it in the opposite direction de-

creases brightness. The figures around the knob indicate the reference

voltage values.

2Placing Specimen on the Stage (Fig. 5)

Fig. 5

# Place the specimen gently. If the bow-shaped lever is returned with

a strong force or the knob 1of the bow-shaped lever is released in

the middle, the slide glass may be broken.

1. Rotate the coarse adjustment knob 2in the direction of the arrow to fully

lower the stage.

2. Open the bow-shaped lever 3outward, place the specimen by sliding

the specimen glass plates on the stage from the front toward the rear.

3. After sliding the specimen glass plates all the way, return the bow-shaped

lever 3gently.

4. Rotating the upper knob which is the Y-axis feed knob 4moves the

specimen in the vertical direction. Rotating the lower knob which is the X-

axis feed knob 5moves it in the horizontal direction.

#Do not move the specimen holder directly by hand, for this will

damage the rotary mechanisms of the above knobs.

#When the specimen holder reaches the stopper position, the

rotation force of the above knobs become heavy. Stop rotating

the knob at this time.

Cover glass

This is the glass plate placed on the specimen. To allow the objective

manifest the full performance, the cover glass thickness, which is the

distance from its surface to the specimen surface, should ideally be

0.17 mm.

Slide glass

This glass plate should ideally have a length of 76 mm, width of 26

mm and thickness between 0.9 and 1.4 mm.

Fig. 6

Placing Specimen

Cover glass

Slide glass

Andere Handbücher für CX21

Inhaltsverzeichnis

Andere Olympus Mikroskop Handbücher

Olympus

Olympus BX53M Bedienungsanleitung

Olympus

Olympus IX73 Bedienungsanleitung

Olympus

Olympus Fluoview FV1000 Bedienungsanleitung

Olympus

Olympus BX45 Bedienungsanleitung

Olympus

Olympus BX-URA2 Bedienungsanleitung

Olympus

Olympus CKX53 Bedienungsanleitung

Olympus

Olympus SZX16 Bedienungsanleitung

Olympus

Olympus DSX510 Bedienungsanleitung

Olympus

Olympus CHD Bedienungsanleitung

Olympus

Olympus CX23 Bedienungsanleitung

Olympus

Olympus U-D7RES Bedienungsanleitung

Olympus

Olympus DP26 Bedienungsanleitung

Olympus

Olympus ORBEYE Handbuch

Olympus

Olympus CHS Bedienungsanleitung

Olympus

Olympus BX41 Bedienungsanleitung

Olympus

Olympus BX3-URA Bedienungsanleitung

Olympus

Olympus DP71 Bedienungsanleitung

Olympus

Olympus bx40 Bedienungsanleitung

Olympus

Olympus VMF Bedienungsanleitung

Olympus

Olympus fsx100 Bedienungsanleitung

Olympus

Olympus bx40 Bedienungsanleitung

Olympus

Olympus SZX-AR1 Bedienungsanleitung

Olympus

Olympus BH2 Series Montageanleitung

Olympus

Olympus BX61 Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Leica

Leica FL560 Bedienungsanleitung