Olympus IX2-RFSPOT Bedienungsanleitung

INSTRUCTIONS

PINHOLE UNIT

AX7383

IX2-RFSPOT

The IX2-RFSPOT has been designed to be used in place of the field iris diaphragm (FS) of a IX2 Series reflected

fluorescence illuminator (IX2-RFAL). When the IX2-RFSPOT is used, a desired pinhole*can be projected on the

specimen plane, which is convenient for canceling the cage on caged specimens.

*No pinhole is provided with the unit. Please fabricate a pinhole yourself (see the figure illustrated later in this

manual) or use the commercially available recommended product (pinhole manufactured by Melles Griot, outer

diameter 16 mm).

1External View

2Precautions for Operation

· Flare is produced around the pinhole. Ghost may be noticeable when the pinhole position is deviated from the center of

the field of view.

· The pinhole image may not be able to be focused perfectly depending on the objective and wavelength in use.

· Centering of the pinhole guarantees only the movement in the center of the field of view. Movement to the peripheral

section of the field is not possible.

· The pinhole position may be deviated slightly when the pinhole is engaged or disengaged. Perform centering whenever

strict positioning is required.

· The pinhole cannot be set to an intermediate position between the IN and OUT positions.

· The IX2-SFR stage gets in the way of centering the pinhole. To prevent it, remount the IX2-SFR with the front in the back or

replace it with the IX-SVL-2.

IX2-RFSPOT

Lamp housing side

Centering screws

Pinhole engagement knob

Pushed in: Pinhole engaged (IN)

Pulled out: Vacant hole (OUT)

Clamping screw

Focus adjustment screw

Microscope frame side

Washers

(x 4)

Clamping ring

3Installation

CAUTION: To ensure safety, be sure to turn off the reflected light source before attaching.

Removing the Field Iris Diaphragm

Using the Allen screwdriver provided with the microscope frame, loosen the field iris diaphragm clamping screw on the

IX2-RFAL and pull out the field iris diaphragm to remove it.

Attaching the Pinhole

1. Using the clamping ring mounting tool provided with the pinhole unit, turn the clamping ring counterclockwise to remove.

2. Drop in the specified number of washers, determined according to the objective and excitation wavelength to be used

(see the list shown later in this manual), in the position where the clamping ring has been placed.

}If the number of washers is wrong, it will not be possible to focus on the pinhole.

3. Place the pinhole, fabricated by you or purchased commercially, above the washers, then clamp by attaching the

clamping ring again.

For the orientation of the pinhole, follow the instructions given with the figure if the pinhole is fabricated by you or insert

with the indications facing down (the lamp housing side) if the pinhole is a commercially available product.

Attaching the Pinhole Unit

Insert the pinhole unit in the microscope position where the field iris diaphragm has been, and clamp the pinhole unit

using the field iris diaphragm clamping screw.

4Operation

}Perform centering in the same way as the field iris diaphragm centering method described in the instruction manual for

the reflected fluorescence system, so that the pinhole is visible in the center of the field of view.

Focusing the Pinhole

Fit the Allen screwdriver into the focus adjustment screw and turn to adjust. (The adjustment range is ±1 mm.)

Centering the Pinhole

Insert the Allen screwdriver alternately into the two centering screws and rotate them so that the pinhole comes at the

center of the field of view.

Engaging/Disengaging the Pinhole

1. Pull out the engagement knob completely to disengage the pinhole from the light path.

2. To re-engage the pinhole in the light path, gently push the engagement knob till the deep.

Relationship Between the Number of Washers and the Objective/Wavelength (This chart is for reference only.

Depending on the objective/wavelength, the pinhole image may not be brought into focus.)

Setting the pinhole diameter

The relationship between the actual pinhole diameter and the diameter of its projection on the specimen surface is as

expressed below.

Pinhole diameter on specimen = 2X (Pinhole diameter/Objective magnification)

(Example) When the pinhole diameter is 100 µm and objective magnification is 40X:

2X (100/40) = 5 µm

#If strict pinhole diameter setting is required, actually project it on a specimen and measure the diameter using

a scale.

Pinhole Design (Unit: mm)

Pinhole position

Microscope frame side

Size indication surface of

common commercially

available pinhole

Lamp housing side

1.6

1.1

16 -0.1

-0.3

UIS2 Series

Objective Type &

Magnification

Excitation Wavelength & Priority*(Brightness/Contrast)

340 nm 360 nm 480 nm

Brightness Contrast Brightness Contrast Brightness Contrast

Number of Washers Number of Washers Number of Washers

UPlanFLN40X X X X X 1 1

UPlanSApo40X X X 0022

PlanApoN60XO X X 2122

UPlanSApo60XW X 00022

UPlanSApo60XO 000022

UPlanSApo100XO 011022

X: Unusable because of impossibility of focusing the pinhole.

* The priority can be changed between the brightness (condition in which light is gathered in the center of the field of

view) and the contrast (position where the pinhole appears sharpest although it looks a little dim) by adjustment of the

mercury lamp’s collector lens.

Printed in Japan 2004 09 M 005–@

UIS Series

Objective Type** &

Magnification

Excitation Wavelength & Priority*(Brightness/Contrast)

340 nm 360 nm 480 nm

Brightness Contrast Brightness Contrast Brightness Contrast

X: Unusable because of impossibility of focusing the pinhole.

*The priority can be changed between the brightness (condition in which light is gathered in the center of the field of

view) and the contrast (position where the pinhole appears sharpest although it looks a little dim) by adjustment of the

mercury lamp’s collector lens.

**Usable regardless of the model number (3, 2 or none).

Number of Washers Number of Washers Number of Washers

UApo20XW3/340 000022

UApo20X3/340 001122

UApo40XOI3/340 000022

UApo40XW3/340 000022

UPlanApo40X X X 0022

UPlanApo40XOI3XXXX22

PlanApo40XWLSM X X X X 2 2

PlanApo60XO3 0 X 1022

UPlanApo60XW3 X X 0022

UPlanApo60XW3/IR X X 0022

PlanApo60XWLSM X X X 4 1 2

PlanApo60XOLSM X X X X 1 2

UPlanFl60XOI3 XXXX22

UPlanApo100XOI3XX0023

Inhaltsverzeichnis

Andere Olympus Mikroskop Handbücher

Olympus

Olympus BHS Bedienungsanleitung

Olympus

Olympus CKX41 Installationsanleitung

Olympus

Olympus Fluoview FV1000 Bedienungsanleitung

Olympus

Olympus DP26 Bedienungsanleitung

Olympus

Olympus JM Bedienungsanleitung

Olympus

Olympus BX41 Bedienungsanleitung

Olympus

Olympus CX40 Bedienungsanleitung

Olympus

Olympus VM Series Bedienungsanleitung

Olympus

Olympus BX60 Bedienungsanleitung

Olympus

Olympus BX43 Bedienungsanleitung

Olympus

Olympus BX-RFAA Bedienungsanleitung

Olympus

Olympus bx40 Bedienungsanleitung

Olympus

Olympus IX71 Bedienungsanleitung

Olympus

Olympus CH30 Bedienungsanleitung

Olympus

Olympus IX2-DSU Bedienungsanleitung

Olympus

Olympus Fluoview FV1000 Bedienungsanleitung

Olympus

Olympus BHTU Bedienungsanleitung

Olympus

Olympus IX81-ZDC2 Bedienungsanleitung

Olympus

Olympus BXFM Series Bedienungsanleitung

Olympus

Olympus FHT-521 Bedienungsanleitung

Olympus

Olympus BX51-P Betriebsanleitung

Olympus

Olympus SZX7 Bedienungsanleitung

Olympus

Olympus BH2 Series Bedienungsanleitung

Olympus

Olympus VS110 Fluorescence Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Leica

Leica FL560 Bedienungsanleitung