Optika SZM-LED1 Bedienungsanleitung

OPTIKA MICROSCOPES - ITALY

www.optikamicroscopes.com - [email protected]

Ver. 1.0.0

SZM-LED1

SZM-LED2

OPERATION MANUAL

MANUEL D’INSTRUCTIONS

GUIDA UTENTE

MANUAL DE INSTRUCCIONES

BEDIENUNGSANLEITUNG

Page 2

INDEX

1.0 DESCRIPTION page 4

2.0 INTRODUCTION page 5

3.0 UNPACKING AND ASSEMBLY page 5

4.0 USING THE MICROSCOPE page 6

5.0 MAINTENANCE page 7

6.0 ELECTRICAL SPECIFICATIONS page 8

7.0 OPTIONAL ACCESSORIES page 8

8.0 RECOVERY AND RECYCLING page 9

Page 3

This microscope is a scientic precision instrument designed to last for many years with a minimum of main-

tenance. It is built to high optical and mechanical standards and to withstand daily use.

Optika reminds you that this manual contains important information on safety and maintenance, and that it

must therefore be made accessible to the instrument users.

Optika declines any responsibility deriving from instrument uses that do not comply with this ma-nual.

Safety guidelines

This manual contains important information and warnings regarding safety about installation, use and

maintenance of the microscope. Please read this manual carefully before using the equipment. To

ensure safe use, the user must read and follow all instructions in this manual. OPTIKA products are

designed for safe use in normal operating conditions. The equipment and accessories described in

the manual are manufactured and tested according to industry standards for safety instrumentation

laboratory. Misuse can cause personal injury or damage to the instrument. Keep this manual at hand

close to the instrument, for an easy consultation.

Electrical safety

Before connecting the power cord to wall outlet, ensure that your mains voltage for your region corre-

sponds to the voltage supply of the instrument, and that the illuminator’s switch is in position OFF. The

user must observe the safety regulations in force in his region. The instrument is equipped with CE

safety marking, in any case the user has full responsibility concerning the safe use of that instrument.

Warning/Caution symbols used in this manual

The user should be aware of safety aspects when using the instrument. Warning or hazard symbols

are shown below. These symbols are used in this manual.

The instructions on this symbol to avoid possible severe personal injuries.

Warning of use; the incorrect operation on the instrument can cause damages

to the person or instrument.

Possibility of electric shock.

Attention: high temperature surfaces. Avoid direct contact.

Technical notes or usage tips.

SAFETY GUIDELINES

Page 4

1.0 DESCRIPTION

SZM-LED2

EYEPIECE

DIOPTRIC

COMPENSATION

FOCUSING KNOB WITH TENSION

CONTROL

OBJECTIVES

INCIDENT

ILLUMINATOR

TRANSMITTED

ILLUMINATOR

ZOOM KNOB

BRIGHTNESS

CONTROLS

PHOTO/VIDEO

TUBE

Page 5

2.0 INTRODUCTION

The OPTIKA zoom stereo microscopes SZM series are high performance Greenough microscopes with con-

tinuous zoom system 0.7:4.5.

These instruments are made for examining any three dimensional object in industrial, biological and educa-

tional applications. They are equipped with two separate optical systems that give an excellent eld depth to

the image, a stereoscopic effect.

3.0 UNPACKING AND ASSEMBLY

The components for the SZM series are shipped in a Styrofoam box for protection. Open the box with care to

avoid that any components fall out and get damaged.

If the instrument has been damaged during the transport, please contact both the carrier and your supplier

immediately.

Unpack the stand and put it on a good stable table. Loosen the lock screw of the focusing carrier, adjust the

height of the focusing carrier and lock the lock screw again.

Put the stereo head onto the focusing carrier and lock it by the lock screw on the side of the focusing carrier.

During the operation of the microscope, this screw should always be locked to maintain maximum stability.

Unpack the eyepieces and other optical parts carefully and place the eyepieces into the eyepiece tubes.

When handling the optical parts, avoid touching any lens surface with naked hand or ngers. Any ngerprints

or grease stains will negatively affect the image quality.

Connect the external power supply plug into the socket at the base

The power cord should be used only on network sockets equipped with adequate grounding.

Contact a technician to check the state of your electrical system. If there is no need to install additional

accessories, the instrument is now ready for use. Once positioned and installed with the necessary

components, the microscope is ready to be used. Your microscope is a laboratory instrument de-

signed to last. Handle it always carefully and avoid abrupt vibrations or shocks. Always disconnect the

power cable from the microscope when not in use for long time, while you clean it or when you perform

any maintenance.

AVOID DISASSEMBLING THE INSTRUMENT

Do not disassemble the instrument. This entails the cancellation of the warranty and may cause

malfunction.

Page 6

4.0 USING THE MICROSCOPE

4.1 Illumination system

The SZM-LED1 and SZM-LED2 come with an integrated illumination system with incident and trans-

mitted light. Before starting, read the section 5.3 about electrical safety precautions. Then, insert

the external power supply and use the brightness controls to turn on the LEDs and control the light

intensity.

The base is equipped with two clips that can be used to block the specimen.

4.2 Adjust interpupillary distance

Hold the right and left parts of the observation head by both hands and adjust the interpupillary dis-

tance by moving the two parts until one circle of light can be seen. If two circles appear, the interpupil-

lary distance is too big, and if two overlapped circles appear,

the interpupillary distance is too small.

4.3 Focus and regulation of the focusing tension

Put the sample to be observed on the plate and turn the zoom

to the highest magnication using the bilateral zoom knob. Try

to focus the sample using the focusing knobs.

4.4 Dioptric compensation

This compensation makes it possible for people with glasses

to adjust the microscope to their eyes and use the microscope

without glasses. Turn the zoom down to the lowest magnica-

tion. Adjust the diopter compensation ring of the right eyepiece

tube until the image of the right eyepiece is clear and sharp.

Repeat the procedure for the left eyepiece. Then, check the

focus of the image for the whole zoom range. It should now

be perfectly parfocal (focus is always maintained during the

change of magnication).

4.5 Magnicationandworkingdistance

The total magnication varies from 1.75x to 180x depending on the eyepieces and auxiliary objec-

tives used. With the bilateral zoom knob, the user can change the magnication in a factor of 6.4 with

perfect parfocality and the image is always centred.

Select the desired magnication by adjusting the bilateral zoom knob. Change the eyepieces and/or

add an appropriate magnifying objective lens if necessary. The total magnication used can be calcu-

lated by the following equation:

Total magnication = Eyepiece magnication x Zoom magnication x Objective lens magnication

Normal working distance for the standard conguration (1x objective lens) is 95 mm.

4.6 Video capturing (optional)

Two kinds of observation heads, binocular or trinocular, are available for the SZM series. They can all

be connected to cameras via an adaptor, for digital and analogical photo and video capturing.

Before taking a picture or lming video, pull out the light path selector lever so the light will be deect-

ed into the photo tube. At the same time, no light will enter into the right eyepiece tube for observation.

Please refer to the adaptor and camera manuals for further details.

Page 7

5.1 Microscopy environment

This microscope is recommended to be used in a clean, dry and shock free environment with a tem-

perature of 0-40°C and a maximum relative humidity of 85 % (non condensing). Use a dehumidier if

needed.

5.2 Tothinkaboutwhenandafterusingthemicroscope

• The microscope should always be kept vertically when moving it and be careful so that no moving

parts, such as the eyepieces, fall out.

• Never mishandle or impose unnecessary force on the microscope.

• Never attempt to service the microscope yourself.

• After use, turn off the light immediately, cover the microscope with the included dust-cover, and keep

it in a dry and clean place.

5.3 Electrical safety precautions

• Users should observe all safety regulations of the region. The equipment has acquired the CE safety

label. However, users do have full responsibility to use this equipment safely.

5.4 Cleaning the optics

• If the optical parts need to be cleaned try rst to: use compressed air.

• If that is not sufcient: use a soft lint-free piece of cloth with water and a mild detergent.

• And as a nal option: use the piece of cloth moistened with a 3:7 mixture of ethanol and ether.

Note: ethanol and ether are highly ammable liquids. Do not use them near a heat source, near

sparks or near electric equipment. Use these chemicals in a well ventilated room.

• Remember to never wipe the surface of any optical items with your hands. Fingerprints can damage

the optics.

• Do not disassemble objectives or eyepieces in attempt to clean them.

5.0 MAINTENANCE

Page 8

Input Voltage: 110/240Vac, 50/60 Hz

Transmitted light: 40mm LED diffusing disc (1,5W power)

Incident light: single X-LED3 (3.6W power)

7.0 OPTIONAL ACCESSORIES

7.1 Eyepieces and auxiliary objectives

With the standard equipment is included a pair of 10x eyepieces. There are also 15x and 20x eye-

pieces available as optional accessories.

To change the eyepieces, remove the original eyepieces and replace with the new pair.

The standard objective is 1x and as optional accessories there are 0,5x, 1,5x, and 2x additional objec-

tives. An additional objective can be needed to obtain a specic magnication or a different working

distance.

The additional objective is mounted simply by screwing it onto the stereo-head. The height of the mi-

croscope has to be re-adjusted as the working distance is changed when additional objective is used.

7.2 Darkeldcondenser

The dark eld condenser has to be used with transmitted light system. By putting this accessory onto

the transmitted light outlet, it creates the dark eld effect. It is especially useful in jewellery or gem

study and special techniques in biomedical applications.

7.3 Photo/Video adapter

This accessory, mounted on the trinocular port, allows a reex camera of any brand to be used on the

microscope in order to capture photos. T2 ring, specic to each model of camera, must be inserted

into the adapter before mounting it on the camera. T2 ring can be purchased in any photocamera

store.

7.4 “C-mount“ adapter

This accessory, mounted on the trinocular port, allows a digital or analog camera to be used on the

microscope in order to capture photos. The camera must have a C-mount or CS-mount connection

type.

6.0 ELECTRICAL SPECIFICATIONS

Page 9

8.0 RECOVERY AND RECYCLING

Art.13 Dlsg 25 july 2005 N°151. “According to directives 2002/95/EC, 2002/96/EC and 2003/108/EC relat-

ing to the reduction in the use of hazardous substances in electrical and electronic equipment and waste

disposal.”

The basket symbol on equipment or on its box indicates that the product at the end of its useful life should be

collected separately from other waste.

The separate collection of this equipment at the end of its lifetime is organized and managed by

the producer. The user will have to contact the manufacturer and follow the rules that he adopt-

ed for end-of-life equipment collection. The collection of the equipment for recycling, treatment

and environmentally compatible disposal, helps to prevent possible adverse effects on the envi-

ronment and health and promotes reuse and/or recycling of materials of the equipment. Improper

disposal of the product involves the application of administrative penalties as provided by the laws in force.

Page 10

INDEX

1.0 DESCRIPTION pag. 12

2.0 INTRODUCTION pag. 13

3.0 DÉBALLAGE ET MONTAGE pag. 13

4.0 UTILISATION DU MICROSCOPE pag. 14

5.0 MAINTENANCE pag. 15

6.0 CARACTÉRISTIQUES ÉLECTRIQUES pag. 16

7.0 ACCESSOIRES FACULTATIFS pag. 16

8.0 RÉCYCLAGE ET RÉCUPÉRATION pag. 17

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Optika Mikroskop Handbücher

Optika

Optika IM Series Bedienungsanleitung

Optika

Optika INSPECTION SYSTEMS Series Bedienungsanleitung

Optika

Optika B-150D-MRPL Montageanleitung

Optika

Optika B-500BSp Bedienungsanleitung

Optika

Optika B-1000 Series Bedienungsanleitung

Optika

Optika OPTIStar OS-SZ1 Bedienungsanleitung

Optika

Optika ECOVISION Series Bedienungsanleitung

Optika

Optika B-383LD1 Bedienungsanleitung

Optika

Optika B-510 Series Bedienungsanleitung

Optika

Optika XDS-3FL Bedienungsanleitung

Optika

Optika B-60 Series Bedienungsanleitung

Optika

Optika B-150POL-M Bedienungsanleitung

Optika

Optika B-810 Series Bedienungsanleitung

Optika

Optika B-510 Series Bedienungsanleitung

Optika

Optika B-1000 POL Bedienungsanleitung

Optika

Optika XDS-3 Bedienungsanleitung

Optika

Optika LAB-1 Bedienungsanleitung

Optika

Optika B-510 Series Bedienungsanleitung

Optika

Optika B-510 Series Bedienungsanleitung

Optika

Optika SZM Bedienungsanleitung

Optika

Optika OPTIKAM FAST3 Series Bedienungsanleitung

Optika

Optika B-380 Series Bedienungsanleitung

Optika

Optika XC-100L Bedienungsanleitung

Optika

Optika B-190 Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Olympus

Olympus SZ61 Bedienungsanleitung