Optika LAB Bedienungsanleitung

microscopes

i T A L Y

OPTIKA MICROSCOPES - ITALY

www.optikamicroscopes.com - [email protected]

Ver. 4.0.0

OPERATION MANUAL

GUIDA UTENTE

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

BEDIENUNGSANLEITUNG

LAB

Page 2

INDEX

1.0 DESCRIPTION page 4

2.0 INTRODUCTION page 6

3.0 UNPACKING AND ASSEMBLY page 6

4.0 USING THE MICROSCOPE page 7

5.0 MAINTENANCE page 8

6.0 ELECTRICS page 9

7.0 OPTIONAL ACCESSORIES page 9

8.0 RECOVERY AND RECYCLING page 10

Page 3

This microscope is a scientific precision instrument designed to last for many years with a minimum of main-

tenance. It is built to high optical and mechanical standards and to withstand daily use.

Optika reminds you that this manual contains important information on safety and maintenance, and that it

must therefore be made accessible to the instrument users.

Optika declines any responsibility deriving from instrument uses that do not comply with this ma-nual.

Safety guidelines

This manual contains important information and warnings regarding safety about installation, use and

maintenance of the microscope. Please read this manual carefully before using the equipment. To

ensure safe use, the user must read and follow all instructions in this manual. OPTIKA products are

designed for safe use in normal operating conditions. The equipment and accessories described in

the manual are manufactured and tested according to industry standards for safety instrumentation

laboratory. Misuse can cause personal injury or damage to the instrument. Keep this manual at hand

close to the instrument, for an easy consultation.

Electrical safety

Before connecting the power cord to wall outlet, ensure that your mains voltage for your region corre-

sponds to the voltage supply of the instrument, and that the illuminator’s switch is in position OFF. The

user must observe the safety regulations in force in his region. The instrument is equipped with CE sa-

fety marking, in any case the user has full responsibility concerning the safe use of that instrument.

Warning/Caution symbols used in this manual

The user should be aware of safety aspects when using the instrument. Warning or hazard symbols

are shown below. These symbols are used in this manual.

The instructions on this symbol to avoid possible severe personal injuries.

Warning of use; the incorrect operation on the instrument can cause damages

to the person or instrument.

Possibility of electric shock.

Attention: high temperature surfaces. Avoid direct contact.

Technical notes or usage tips.

SAFETY GUIDELINES

Page 4

1.0 DESCRIPTION

LAB 10

EYEPIECES

DIOPTRIC COMPENSATION

OBJECTIVE

LIGHT INTENSITY

ADJUSTMENT

CLIPS

POWER SWITCH

FOCUSING KNOBS

Page 5

1.0 DESCRIPTION

LAB 20

EYEPIECES

DIOPTRIC COMPENSATION

OBJECTIVE

LIGHT INTENSITY

ADJUSTMENT

CLIPS

POWER SWITCH

FOCUSING KNOBS

ZOOM KNOB

Page 6

2.0 INTRODUCTION

This microscope is a scientific precision instrument designed to last for many years with a minimum

of maintenance. It is built to high optical and mechanical standards and to withstand daily classroom

and laboratory use.

The OPTIKA LAB series microscopes are high performance Greenough stereo microscopes with

objectives 2x or 4x (LAB-10) or a continuous zoom 0,7x-4,5x (LAB-20). Total magnification varies

from 3,5x to 67,5x depending on the eyepieces and auxiliary objectives used. With this parfocal sys-

tem, the user can enjoy excellent depth of field and stereo effect to be able to examine all types of

gross materials in three dimensions for industrial, biological and educational applications.

Optika reminds you that this manual contains important information on safety and maintenance, and

that it must therefore be made accessible to the instrument users.

Optika declines any responsibility deriving from instrument uses that do not comply with this manu-

al.

3.1 The microscope is housed in a moulded styrofoam container. Remove the tape from the

edge of the container and lift the top half of the container. Take some care to avoid that

the optical items fall out and get damaged. Using both hands (one around the arm and one

around the base), lift the microscope from the container and put it on a stable desk. Be care-

ful not to touch any of the lens surfaces.

3.2 Loosen the lock screw of the focusing carrier, adjust the height of the focusing carrier and

lock the lock screw again.

3.0 UNPACKING AND ASSEMBLY

Page 7

4.0 USING THE MICROSCOPE

4.1 Place the specimen on the stage

Place the specimen on the microscope stage and lock the specimen slide using the slide-

clamp if it is necessary. Ensure that the specimen is centred over the stage opening.

4.2 Turn on the light

The microscope comes with an electrical illuminator. Insert the plug of the cable into the power socket

and turn on the switch on the main body and select your light source. Turn the light intensity control to

a brightness suitable for observation.

4.3 Adjust interpupillary distance

Hold the right and left parts of the observation head by both hands and adjust the interpupillary distance

by turning the two parts until one circle of light can be seen. If two circles appear, the interpupillary dis-

tance is too big, and if two overlapped circles appear, the interpupillary distance is too small.

4.4 Focus

Rotate the focusing knob to bring the slide into focus with the highest magnification.

4.5 Dioptric compensation

This compensation makes it possible for people with glasses to adjust the microscope to their eyes and

use the microscope without glasses. Turn the zoom down to the lowest magnification. Adjust the diopter

compensation ring of the right eyepiece tube until the image of the right eyepiece is clear and sharp. Re-

peat the procedure for the left eyepiece. Then, check the focus of the image for the whole zoom range.

It should now be perfectly parfocal (focus is always maintained during the change of magnification).

4.6 Magnification

Select the desired magnification by adjusting the zoom knob. Change the eyepieces and/or add an ap-

propriate magnifying objective lens if necessary. Total magnification used can be calculated as:

Eyepiece magnification x Zoom magnification x Objective lens magnification

4.7 Working distance

Normal working distance for the standard configuration is 80 mm (LAB-10) and 85mm (LAB-20).

Connect the mains plug into the socket at the base

Make sure, before you turn the illumination on, that the voltage selector is set to the mains voltage for

your region.

The power cord should be used only on network sockets equipped with adequate grounding.

Contact a technician to check the state of your electrical system. If there is no need to install additional

accessories, the instrument is now ready for use. Once positioned and installed with the necessary

components, the microscope is ready to be used. Your microscope is a laboratory instrument desi-

gned to last. Handle it always carefully and avoid abrupt vibrations or shocks. Always disconnect the

power cable from the microscope when not in use for long time, while you clean it or when you perform

any maintenance.

AVOID DISASSEMBLING THE INSTRUMENT

Do not disassemble the instrument. This entails the cancellation of the warranty and may cause

malfunction.

Page 8

5.1 Always think about

- The following environment is required: Indoor temperature: 0-40°C, Maximum relative humid-

ity: 85 % (non condensing)

- Keep the microscope away from dust and shocks while in use.

- Turn off the light immediately after use.

- Use a soft lens tissue or compressed air to clean the optics after use.

- Only if needed, use a cloth moistened with water and a mild detergent, rinsing with water and

drying immediately with a lint-free cloth.

- After use, cover the microscope with the included dust-cover, and keep it in a dry and clean

place.

5.2 Do not!

- Wipe the surface of any optical items with your hands. Fingerprints can damage the optics.

- Use solvents, neither on the microscope, nor on the optics.

- Disassemble objective or eyepieces to attempt to clean them.

- Mishandle or impose unnecessary force on the microscope.

- Clean the unit with volatile solvents or abrasive cleaners.

- Attempt to service the microscope yourself.

5.3 How to change the fuse

In case of malfunctioning of the illumination, replace the fuse on the bottom of the stand:

unscrew the old fuse and replace it with a new fuse with the same specifications.

5.0 MAINTENANCE

Page 9

6.0 ELECTRICS

6.1 Universal Power: 230 V, 50 Hz

Lamp: 3W WHITE LED, 6300K [incident and transmitted]

ST-001 Eyepieces (pair) WF5x/22mm

ST-401 Eyepieces (pair) WF10x/20mm

ST-402 Eyepieces (pair) WF15x/15mm

ST-403 Eyepieces (pair) WF20x/10mm

ST-005 Micrometric eyepiece WF10x

ST-410 Additional lens 0,5x for LAB 2 (w.d. 170 mm)

ST-411 Additional lens 1,5x for LAB 2 (w.d. 42 mm)

ST-415 Eye cups (pair) type 1

ST-417 Semi-transparent plastic stage

ST-029 Dust cover type 12

7.0 OPTIONAL ACCESSORIES

Page 10

8.0 RECOVERY AND RECYCLING

Art.13 Dlsg 25 july 2005 N°151. “According to directives 2002/95/EC, 2002/96/EC and 2003/108/EC

relating to the reduction in the use of hazardous substances in electrical and electronic equipment

and waste disposal.”

The basket symbol on equipment or on its box indicates that the product at the end of its useful life

should be collected separately from other waste.

The separate collection of this equipment at the end of its lifetime is organized and managed by

the producer. The user will have to contact the manufacturer and follow the rules that he adopted

for end-of-life equipment collection. The collection of the equipment for recycling, treatment and en-

vironmentally compatible disposal, helps to prevent possible adverse effects on the environment

and health and promotes reuse and/or recycling of materials of the equipment. Improper disposal

of the product involves the application of administrative penalties as provided by the laws in force.

Inhaltsverzeichnis

Sprachen:

Andere Optika Mikroskop Handbücher

Optika

Optika B-290 Bedienungsanleitung

Optika

Optika B-150D-MRPL Montageanleitung

Optika

Optika B-800 Bedienungsanleitung

Optika

Optika XDS-3FL Bedienungsanleitung

Optika

Optika B-510 Series Bedienungsanleitung

Optika

Optika XZ-2 Bedienungsanleitung

Optika

Optika B-500POL Bedienungsanleitung

Optika

Optika IM-2 Bedienungsanleitung

Optika

Optika SZN Series Bedienungsanleitung

Optika

Optika B-500Ti-2 Bedienungsanleitung

Optika

Optika B-380 Series Bedienungsanleitung

Optika

Optika IM Series Bedienungsanleitung

Optika

Optika B-1000 Series Bedienungsanleitung

Optika

Optika B-50 Bedienungsanleitung

Optika

Optika B-1000Ti-2 Bedienungsanleitung

Optika

Optika STEREO Series Bedienungsanleitung

Optika

Optika B-1000 POL Bedienungsanleitung

Optika

Optika B-510 Series Bedienungsanleitung

Optika

Optika OPTIKAM FAST3 Series Bedienungsanleitung

Optika

Optika XDS-3 Bedienungsanleitung

Optika

Optika B-150POL-M Bedienungsanleitung

Optika

Optika OPTISTAR OS-A1 Series Bedienungsanleitung

Optika

Optika B-500BSp Bedienungsanleitung

Optika

Optika OPTIGEM Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Olympus

Olympus SZ61 Bedienungsanleitung