PR Lighting CHAMELEON PR-2012H Bedienungsanleitung

CHAMELEON

PR-2012H

This product manual contains important information about the safe installation and

use of this projector. Please read and follow these instructions carefully and keep this

manual in a safe place for future reference.

PR LIGHTING LTD.

Yingbin Road, Dashi Panyu, Guangzhou, 511430 China

http://www.pr-lighting.com

Chameleon manual.doc

2/12

SECTION PAGE

SAFE USAGE OF THE PROJECTOR 3

INSTALLING THE PROJECTOR 4

FITTING THE LAMP 4

POWER SUPPLY –MAINS 4

OPERATION5

XLR CONNECTORS AND TERMINATOR 5

STAND-ALONE MODE 6

MASTER/SLAVE SYNCHRO MODE 6

CONTROLLER MODE -DMX OPERATION 7

MAINTENANCE 9

KEEPING THE PROJECTOR CLEAN 9

TROUBLE SHOOTING 9

TECHNICAL DATA 10

ELECTRICAL DIAGRAM 11

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change

without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the

course of product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any

consequence arising from them.

Every apparatus is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the

apparatus is in good condition before your installation and use. Should there be any damage caused by transportation, consult

your dealer and do not use the apparatus. But any damage caused by improper use will not be assumed by the manufacturer

and / or dealer.

THESE ITEMS ARE PACKED TOGETHER WITH THE PROJECTOR

Mounting Bracket (1 PCS)

M8 knobs for bracket (2 PCS)

Safety cord (1 PCS)

Power-cord (1PCS)

XLR plug (1 PCS)

XLR socket (1 PCS)

This manual (1PCS)

Thank you for purchasing our product CHAMELEON, PR-2012H.

CHAMELEON adopts advanced procedure of design and manufacturing and uses international

protocol DMX 512 and complies to CE norms. The outline of housing is elegant, lovable and portable,

which features its special character compared with conventional luminaire. It is convenient to hang the

unit and the angle of the body is easy to be adjusted, and the projector even can be carried by hand.

The unit can be controlled by sound, auto programmes or a controller, and can be used as a stand-

alone unit or linked with each other for multi-units or linked to a controller, so it is suitable for many

different applications.

The lamp brightness can be adjusted and it will be switched off automatically after about 30 seconds

of shutter, so it can effectively prolong the life of the lamp and the projector.

The unit features 8 colourful dichroic filters, and it may produce strobe/shutter and rainbow effect when

the color wheel rotates fast.

The unit has auto thermal cut-off device for the unit operating in a safety condition.

ACCESSORIES

INDEX

INTRODUCTION

Chameleon manual.doc

3/12

The following points are important for safety as well as for the smooth

installation and performance of the unit

When unpacking and before disposing of the carton check there is no transportation damagebefore

using the projector. Keep the carton well for future possible transportation. Should there be any

damage caused by transportation, consult your dealer and do not use the apparatus.

The projector is for Indoor use only, IP20. Use only in dry locations. Keep this device away from rain

and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other fluids, or

metallic objects.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Do not project the beam onto inflammable surfaces, minimum distance is 3m. 3m

Avoid direct exposure to the light from the lamp. The light is harmful to the eye.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power

requirements of the projector. Please use the lamp with the specified type and rating.

It is essential that each projector is correctly earthed and that electrical installation conforms to all

relevant standards.

Do not connect this device to any dimmer pack.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-

cord come into contact with other cables. Only handle the power-cord by the plug. Never pull out the

plug by tugging the power-cord.

Never run the projector without a lamp.

Switching the lamp on and off at short intervals will reduce the life of both the lamp and the projector.

Occasional breaks will prolong the life of the lamp and the projector.

There are no user serviceable parts inside the projector, do not open the housing and never operate

the projector with the covers removed.

Always disconnect from the mains, when the device is not in use or before

cleaning it or before attempting any maintenance work.

If you have any questions, don’t hesitate to consult your dealer.

SAFE USAGE OF THE PROJECTOR

Chameleon manual.doc

4/12

This unit has been designed to be hung. Mount the bracket provided on the body of the projector.

There are 2 M8 knobs provided to tighten the body and the bracket. When you want to adjust the

angle of the body of the projector, you only loosen the two M8 knobs carefully and then adjust the

angle of the body. After finishing that, it is recommended that you don’t forget to retighten the two M8

knobs. Always ensure that the projector is firmly positioned to avoid vibration and slipping and always

ensure that the structure to which you are attaching the projector is secure and is able to support a

weight of 6.9kg for each CHAMELEON.

For safety the unit should have a secondary fixing with a safety cable through the two handles on the

back of the unit, and the safety cable should afford 10 times of the unit’s weight.

Remove the lamp access hatch

by loosening the 2 M4 screws

Insert an ELC-7/X 24V/250W

lamp in the lamp-holder.

Plug the lamp into the lamp-

bracket until the lamp is fully

seated, and let the two spring

press the lamp stably.

Install the lamp access hatch

again.

Retighten the 2 M4 screws.

Use the plug provided to connect the mains

power to the projector paying attention to the

voltage and frequency marked on the panel of

the projector. It is recommended that each

projector is supplied separately so that they

may be individually switched on and off. It is

recommended that the green/yellow power-

cord must be earthed correctly.

FITTING THE LAMP

INSTALLING THE PROJECTOR

POWER SUPPLY -MAINS

Chameleon manual.doc

5/12

The projector can be controlled by sound, auto-programmes or a controller, and can be operated in

Stand-Alone mode, Master/Slave synchro mode or Controller mode.

When the power is on, the projector will reset automatically for operation.

TO SET THE ADDRESS OF DIP SWITCHES

The DIP switch of the CHAMELEON has 10 switches with the number from 1 to 10, which may be set

on the “ON” or “OFF” position. You should set the DIP switch correctly to operate the projector. (See

“Stand-alone mode”, “Controller mode” and “Master/Slave synchro mode” for detail)

XLR CONNECTORS

Connection between controller and projector and between one projector and another must be made

with 2 core screened cable, with each core having at least a 0.5mm diameter. Connection to and from

the projector is via cannon 3 pin XLR plugs and sockets which are included with the projector. The

XLR's are connected as shown in the figure above.

Note, care should be taken to ensure that none of the connections touch the body of the plug or each

other. The body of the plug is not connected in any way. The CHAMELEON accepts digital control

signals in standard DMX512 (1990) format.

5-PIN AND 3-PIN CONVERSION

CHAMELEON uses 3-pin XLR plug / socket. If your controller uses 5-pin XLR plug / socket, you

should convert 5-pin plug / socket into 3-pin socket / plug as shown below.

DMX TERMINATOR

In the Controller mode or Master/Slave mode, the DMX output has to be connected with a DMX

terminator at the last fixture in the chain. This prevents electrical noise from disturbing and corrupting

the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2

and 3, which is then plugged into the output socket on the last projector in the chain. The connections

are illustrated on the right.

The terminator is added a 120Ωresistor between pin-2 and pin-3 in a Canon plug, which can avoid the

reflection during the DMX-512 signal transmission.

DMX TERMINATOR

CONNECTION

Connect a 120Ω(OHM) resistor across

pins 2 and 3 in an XLR plug and insert

into the DMX OUT socket on the last

unit in the chain.

OPERATION

XLR CONNECTORS AND TERMINATOR

Chameleon manual.doc

6/12

Without connecting a controller with the projector, the projector will run in Stand-Alone mode controlled

by sound or auto programmes via setting the DIP switch as shown below.

When sound activating, the projector will change the colours according to the rhythm of the music.

You may rotate the audio sensitivity controller for the best receiving sound signal.

When running the auto programmes, the red LED is constant on. When running the sound activation,

the red LED will flashing according to the rhythm of the music.

Without using the controller, many projectors can run

synchronously by linking them with each other in the

Master/Slave mode.

Select one projector as the master without connecting

any cable to the projector’s input, and set DIP switch

as shown on the right.

Regard the other projectors as the slaves, and set the

DIP switch as shown on the right.

Connect the master’s output to the first slave’s input,

and connect the first slave’s output to the second

slave’s input. The rest may be deduced by analogy.

Eventually connect the last slave’s output to a DMX

terminator as shown in the figure above.

In the Master/Slave mode, all slaves will change

colors and gobos synchronously according to the

master.

MASTER / SLAVE SYNCHRO MODE

STAND-ALONE MODE

Chameleon manual.doc

7/12

DMX512 CONTROL CHANNEL FUNCTIONS

CHAMELEON has 2channels and uses DMX 512 control protocol. They are listed in the following

table.

CHANNEL DMX 512 VALUE DESCRIPTION

0 -16 Black-out

17 -33 Strobe

34 -50 White

51 -67Cyan

68 -84Yellow

85 -101 Green

102 -118 Purple

119 -135 Orange

136 -152 Red

153 -169 Pink

170 -179 Blue

COLOUR

180 -255 Colour wheel rotates in clockwise or anti-clockwise

direction from slow to fast

2 DIMMER 0 -255 Lamp brightness adjust from dark to bright

CONTROLLER AND PROJECTOR CONNECTION

Connect the controller’s output to the first projector’s input, and connect the first projector’s output to

the second projector’s input. The rest may be deduced by analogy. Eventually connect the last

fixture’s output to a DMX terminator as shown in the figure below.

The red LED blinking means the projector is receiving DMX 512 signal normally.

CONTROLLER MODE –DMX OPERATION

Chameleon manual.doc

8/12

TABLE FOR SETTING ADDRESS OF DIP SWITCHES

The following table lists the setting codes of the address of the DIP switches, and the luminaires are

from No.1 to No. 256. Each DIP switch has 10 switches with the number of #1, #2, #3, #4, #5, #6, #7,

#8, #9 and #10. (For the CHAMELEON, set all #10 switches on the “OFF”.)

In the table, “0” means the switch is on the “OFF”, and “1” on the “ON”.

For example, if you want to look up the address setting of the No 50 luminaire, you will find the NO 50

luminaire row (#1, #2, #3, #4, #5) with the codes of “1”, “1”, “0”, “0” , “0” and column (#6, #7, #8, #9)

with the codes of “1”, “1”, “0” , “0”. So set the #1, #2, #6 and #7 switches on the “ON”, and set the #3,

#4, #5, #8, #9, and #10 switches on the “OFF”.

Setting Table of

DIP Switches #8

0=OFF #7

1=ON #6

113

129

145

161

177

193

209

225

241

114

130

146

162

178

194

210

226

242

115

131

147

163

179

195

211

227

243

100

116

132

148

164

180

196

212

228

244

101

117

133

149

165

181

197

213

229

245

102

118

134

150

166

182

198

214

230

246

103

119

135

151

167

183

199

215

231

247

104

120

136

152

168

184

200

216

232

248

105

121

137

153

169

185

201

217

233

249

106

122

138

154

170

186

202

218

234

250

107

123

139

155

171

187

203

219

235

251

108

124

140

156

172

188

204

220

236

252

109

125

141

157

173

189

205

221

237

253

110

126

142

158

174

190

206

222

238

254

111

127

143

159

175

191

207

223

239

255

112

128

144

160

176

192

208

224

240

256

Chameleon manual.doc

9/12

If the projector’s lens becomes damaged or broken it should be replaced. If the lamp becomes

damaged or deformed in any way it must be replaced. If the light from the lamp appears dim this would

normally indicate that it is reaching the end of its life and it should be changed at once, old lamps run

to the extremity of their life can explode. If the projector does not function, check the fuses on the

power socket of the projector, it should only be replaced by fuse of the same specified value 4A/250V

(fast blow, 5mmx20mm). Should these be damaged call a qualified technician before replacement.

The projector has thermal protection device that will switch off the projector in case of overheating,

should either of these operate, check that the fans are not blocked, and if they are dirty clean them

before switching on the projector again. Check that the fans are operational, if not call a qualified

technician.

Any maintenance work should only be carried out by qualified technicians.

To ensure the reliability of the projector it should be kept clean. It is recommended that the fans should

be cleaned every 15 days. The lens and dichroic colour filters should also be regularly cleaned to

maintain an optimum light output. Do NOT use any type of solvent on dichroic colour filters.

Cleaning frequency depends on the environment in which the fixture operates: damp, smoke or

particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics. A soft cloth

and typical glass cleaning products should be used in cleaning. It is recommended to clean the

external optics at least once every 20 days and clean the internal optics at least once every 30 / 60

days.

Do not use any organic solvent, e.g. alcohol, to clean the housing of the

projector.

PROBLEM RESOURCE

The projector does not start Check the fuse on the socket is blown or not.

Check if the lamp is good or not.

The projector switches on but does not

answer to commands Check setting the DIP switch is correct.

Check the XLR cable is good.

The projector only functions

intermittently Check the fan is working and not dirty.

The beam appears dim Check the lamp is not at the end of its life.

Check the optics are clean.

Projection with halo Carefully clean the lamp, the optical group lenses.

Defecting projection Check the lenses are not broken.

Remove dust or grease stored on lenses.

MAINTENANCE

TROUBLESHOOTING

KEEPING THE PROJECTOR CLEAN

Chameleon manual.doc

10/12

Power supply: 230V AC 50Hz

Optional: 240V, 220V, 200V, 120V, 100V AC 50/60Hz

Power consumption: 280W at 220V

Lamp: ELC-7/X 24V/250W

Channels: 2 channels

Control signal:Standard DMX 512

Control mode: Sound activation / Auto programmes / Controller

Running mode: Stand-Alone mode / Master/Slave synchro mode / Controller mode

Colours:8 colours + white + black-out

Beam coverage: 11°

Net weight: 6.9kg

Others: Adjustable lamp brightness / Auto thermal cut-off / Rainbow effect /

Strobe effect / Auto cut-off lamp after about 30 seconds of shutter

TECHNICAL DATA

Inhaltsverzeichnis

Andere PR Lighting Beleuchtungsausrüstung Handbücher

PR Lighting

PR Lighting AQUA 380 BWS Bedienungsanleitung

PR Lighting

PR Lighting PR-8846 Bedienungsanleitung

PR Lighting

PR Lighting PR-2001L Bedienungsanleitung

PR Lighting

PR Lighting XL 1500 Bedienungsanleitung

PR Lighting

PR Lighting XR130 Beam Bedienungsanleitung

PR Lighting

PR Lighting XPar 150 Zoom Bedienungsanleitung

PR Lighting

PR Lighting XLED 590 Bedienungsanleitung

PR Lighting

PR Lighting CUBIX300 Bedienungsanleitung

PR Lighting

PR Lighting PR-8121 Bedienungsanleitung

PR Lighting

PR Lighting AQUA 580 BWS Bedienungsanleitung

PR Lighting

PR Lighting DESIGN 150 Bedienungsanleitung

PR Lighting

PR Lighting PR-2203 XR 200 Bedienungsanleitung

PR Lighting

PR Lighting LS150 TREE Bedienungsanleitung

PR Lighting

PR Lighting PR-2330 Bedienungsanleitung

PR Lighting

PR Lighting PR-8170A Bedienungsanleitung

PR Lighting

PR Lighting AQUA 380 BEAM Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

PR Lighting

PR Lighting PR-111ER MOON Bedienungsanleitung

PR Lighting

PR Lighting PR-8920 Bedienungsanleitung

PR Lighting

PR Lighting ARC LED 372 Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 1500 SPOT Bedienungsanleitung

PR Lighting

PR Lighting PR-8120 Bedienungsanleitung

PR Lighting

PR Lighting XR 200 BEAM Leitfaden

PR Lighting

PR Lighting XR250 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung