PR Lighting CUBIX300 Bedienungsanleitung

CUBIX300

PR-6803

The user manual contains important information about the safe installation and use of a projector. Please read

andfollowthese instructions carefullyandkeepthemanual in asafeplaceforfuturereference.

PR LIGHTING LTD.

http://www.pr-lighting.com

INDEX

1.SAFETYANDWARNINGS

2. INSTRUCTIONS

3.INSTALLATION

4.SETUPANDCONFIGURATION

5.OPERATIONMENU

6.DMXPROTOCOL

7.TECHNICALDATA

ACCESSORIES

Thefollowing itemsaresuppliedwith theprojectorand pleasecheck:

Name

Quantity

Unit

Remark

Clamp

Power cord

XLRloopcable

pcs

Safetycord

User manual

Please note that as part of our ongoing commitment to continuous product development, specifications are subject tochange without notice.

Whilst every care is taken in the preparation of the manual we reserve the right to change specifications in the course of product

improvement.Thepublisherscannotbeheldresponsiblefortheaccuracyoftheinformationherein,oranyconsequencearisingfromthem.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good

condition beforeinstallation anduse.Shouldthere be any damage causedbytransportation, consultyourdealerand donot usetheunit. Any

damagecausedbyimproperusewill notbeassumedby themanufacturerand/ordealer.

Any future technical change in the user manual won’t be with any further notice.

Note: Forthe products made by GuangzhouPRlighting Ltd,thewarranty for the whole product is oneyear startingfrom the delivery date

butthelightsourceisnotwithinthewarranty

1. SAFETYANDWARNINGS

NOTE

Before a projector’s installation, power-on,operationandmaintenance,pleasecarefullyread

thesafetyinformationhereinafter!

The followingsafetysignsareusedintheusermanual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Flames

High

Temperature

● When unpacking , check if there is transportation damage before using the projector. Should there be any

damage caused bytransportation, consultyourdealeranddo not useit.

●The manufacture is not responsible for loss caused by the user not following the manual or changing the

projector ashe/shelikes

●Please be noted that the damage caused by changing theprojector atwill isnotwarranted.

● Do not hesitate to contact the dealer or the manufacturer if any questions or advice.

●The unit can be used indoors and outdoors with IP65.

●The projector should be kept away from high temperature, fire, electrical surge, vibrationand stronglightwhile

beingoperated

●The projector is only intended for installation, operation and maintenance byqualifiedpersonnel.Andthe

operationmuststrictlyfollowtheproceduresinthemanual

●No repairable parts in theprojectoranddo notopencovers formaintenancebyyourself.

●Don’t look straightly into the light sources especially for epileptics,otherwiseeyeswillbeburned.

●Donotconnecta projectortoanytypeofdimmer pack.

●Ifthelamp,lensand screenprotectivecoveroftheaprojectorhaveobviousdamage,i.e.,tothe extentthat it

hurtstheperformancelikecracking ordeformation.Pleasestopusingitand replacethemwiththeoriginalparts,

otherwiseitsperformancewillbecompromised.

● For theinstallationlocationofaprojector, it shouldn’t be seen in the distance of less than 4 meters for a long

time.

●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a

projector whilecovers(housing)areoff

●Keep the lamp clean and do not touch it with bare hands.

●While operating it, wear protective items.

●Any electrical connection must be carried out by a qualified person .

●Before installation, please confirmthe voltagesupplied matcheswhatisrequired fortheprojector

●Each projector must be properly earthed and installed as per related electrical standards.

●Do not use power cord with its insulator damaged and connect the power cord with other cables.

●If the projector is not used or under cleaning,, please hold the plug and unplug it. Do notunplugitforcefullyor

bypullingthepowercable.

●All power cords must conform to related safety and regulations

●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other

electrical parts’ life will be shortened

●There are safety cord holes at the bottom of the base of a projector. In view of safety,pleaserunthesafetycord

suppliedthroughthe safetycord holesforsafetysupport.

●Before any installation, maintenance and cleaning work, please ensure the projectorisdisconnectedfrom

powermains.

●While the ambient temperature is stable, the highesttemperatureof thehousingwillbe70℃

●While operated, do not touch the metallic housing. It is very hot during operation.

●Do not mount the projector directly on inflammable surface.

●Do not project the beam straightly on combustible items and the minimum distance between theprojectorand

illuminateditemsis10m.

●A projector should be installed with good ventilation and the minimum distancebetweentheprojectorand

wallsis 50cm.Atthesametime,pleaseensurethefansandairinletsandoutletsareworkable.

●Donotletthe frontlens under sunlightorother stronglight sourcesatanyangle,otherwise the dangeroffire

canbecausedbythe focused beambythe lensinsideaprojector.

2. INSTRUCTIONS

●CLEANINGANDMAINTENANCE

For the units with optical lens, because of the accumulation of the smoke, oil and dust on lens, the light output will be

compromised. For the reliable use of the unit, it is very necessary to keep it clean. The unit is IP65 rating waterproof device.

Unless approval by some professional technician for necessary internal component replacement, it’s forbidden to dismantle the

unit.

Cleaning frequency isto be decided byoperations and its environment. Use soft clothand normal detergent forglass for cleaning

work. It’s advised external optical system be cleaned every 20days. Keep lens clean and do not touch optical parts with bare

hands.

●Beforeanymaintenanceandcleaning,pleaseensuretheprojectisoffthepower

●Onlyqualifiedpersonisallowedtodomaintenance

●Duringmaintenance andbeforemaintenance,theprojectormustbeoffpower.

●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens

whether itrunsor not

●Donotuse alcoholorotherorganicsolventtocleanthehousingtoavoiddamage.

●Donot useanysolventwith chemical elementsto cleancolor filtersor hot mirror.

●TROUBLESHOOTING

PROBLEM

ACTION

The projector doesn’t switch on

Checkthepowercord connection

Power Switch fails or is not connected well, call a professional

technicianforrepairingandchecking

Control board is not connected normally, call a professional technician

forrepairingandchecking,

Theprojectcanbeturnedon,but the LED lamps

can’t be on

LED lamp board is not connected well, calla professional technician for

repairing and checking

TheLEDlamps canbeon,butnotcontrolled

byDMX

CheckifDMXStartAddressisproperlyset

CheckifXLRcablefailsornot

Thebrightnessdecreasesobviously

Ambient temperature is too hot which makes the projector too hot,

pleasetakeappropriateventilationmeasures

3. INSTALLATION

●PLACEAUNITONAFLATSURFACE

Before placing a unit on a flat surface, loosen the small knob with the support and make the angle between the arm and the support

60degrees. Tightenthe small knob. Loosen he bigknob and adjust the angle between thearm and unit as desired and then tighten it.(if

theversionis withwirelesscontrol,the antennashould faceup ifthe fixtureisplacedonflatsurface)

●TRANSPORTATION

Before transportation,tighten both knobs after the arm and supportareoverlapped.

WARNING:

●The projectorMUSTbeliftedorcarriedbytheHANDLESinsteadofclamps.

●.Forsafetythesafetycordshouldafford10times the Projector’s weight.

●POWERCONNECTION

Connectthepowercordasfollows:

L(live)=brown

E(earth) =yellow/green

N(neutral)=blue

Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that each

projector be connected withpower separatelyso that theymaybeindividuallyswitchedonand off.

Note: If projectors are connected in series, please connect POWER IN port of the 1st projector with the Power Mains, then

connectitsPOWEROUTwithPOWERINof the2nd projector,andsoontillallfixturesareconnected.Ifthe voltagesupplied

is 200V-240V, the maximum projectors connected is 8pcs, if it is 100V-120V, the maximum is 4pcs. The diameter of the cores

ofthewiresforthe Powerin/outcablesmustbeequalorbiggerthan2.5mm2.

●Theearthwire(yellow/green) must be connectedto theground.Andelectricalconnectionmust be in

accordancewiththe standardsconcerned.

●Ifanyquestionsabouttheelectricalinstallation, donot continue but consult aqualifiedelectrician.

●DMXCONTROLCONNECTION

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with

each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the

projector)or5pinXLRplugsand sockets.The XLR'sareconnectedasshown inthe figureabove.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets

mustn’t be connected in any way other than mentioned in the above figure. The unit accepts digital control signals in protocol

DMX512(1990).

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second

fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX

terminatorasshown inthe figurebelow.

●DMXTERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electricalnoise fromdisturbingandcorruptingtheDMXcontrolsignals.

The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected across pins 2 and 3, whichis then plugged

intotheoutputsocketonthe lastprojectorinthechain.The connectionsare illustratedbelow.

4. SETUPANDCONFIGURATION

●FRONTPANELOPERATION

To browse through or modify the projector’s functions, press key ENTER for more than 3 seconds to unlock the control panel and

enter the menus. To set or browse through the projector’s functions, press key UP or DOWN. Press the key ENTER to enter the

submenus andthecurrentparameterswillbedisplayedwhileflashing.Presskey UP or DOWN tochange values(plusor minus)

Presskey ENTER to save yourchangesand enter into the upperlevel menu while flashings stop;

Presskey FUNC, it willreturntothe upper menu(parametersnot saved)orbrowsethrough1st levelmenus;

Presskey FUNC for 1secondornone keyis pushed for1minute,themenu willbeescaped and currentoperationmodedisplayed.

●DMXSTARTADDRESS

EachProjectormustbe givena DMXstartaddress sothatthe correctprojectorrespondstothecorrectcontrolsignals.ThisDMXstart

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

DMX Controller

DMX Teminator DMX OUT

DMX IN

DMX OUT

DMX IN

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain. PIN 3

PIN 2

controller. The Unit has 1 DMX mode. For example standard mode has 9 channels, so set the No. 1 projector’s address 001, No. 2

projector’s address 010, No. 3 projector’s address 019, No. 4 projector’s address028,and so on.

Launchtheprojector.Pressbutton ENTER morethan3secondsto unlockpanel.

Pressbutton ENTER todisplayDMXaddress;

Pressbutton UP and DOWN, youcansettheaddress;

Pressbutton ENTER toconfirm;afterpoweredonnexttime,thedefaultwillbelast valuesaved

Pressbutton FUNC,it willreturntothe uppermenu

IfDMXsignal isavailable, LEDindicationison.Otherwiseitisoff.

●WIRELESS CONTROL OPERATION

The optional version of the projector has wireless control function with DMX wireless receiver module and DMX wireless antenna

forremotecontrol.

Theoperationdetailsareasfollows:

1. Enter into the menu, then enter into “Config Set” after UP or DOWN ispushed;

2.Select “Wireless mode” －→”Wireless first”(Note: do not select” XLR only); Then the wireless control is activated. Only

after the project and wireless transmitter are connected, can the it receive wireless signal. If wireless control is deactivated,

press “Yes” under “Unlink wireless” under “config Set”. Then the projector will disconnect wit the wireless transmitter.

●STAND-ALONEMODE

Operate the projector without connecting with a controller, enable the master mode through the operation panel, the

projector will run in Stand-Alone mode automatically.

DMX address can be set at any number within 512.

●MASTER/SLAVEMODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,

connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR control cable and then connect the second

fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the

last fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.

StartAddressesof all Slaves are 001; Operation mode of the Master can be set any mode for a Master’ and Slaves’ operation mode can

be setaccordingly

AfterPoweredon,thegroupwillruninMaster/SlaveMode

Slave MasterSlave

DMX OUT

DMX IN

DMX OUT

DMX IN

DMX Teminator

5. OPERATIONMENU

1st levelmenu

2nd levelmenu

3rd level menu

4th levelmenu

Address

001 -512

DMXAddress

ConfigSetup

MasterSlave

Slave

Default：Slave

Master

LanguageSetup

English

Default：English

Chinese

LcdLightSetup

Backlightwillbeoff

3mintuesafternokeyis

pushed.

Off

DisplayInvert

Yes

FactorySetting

Yes

PRMTransmit

Yes

cleanProgra

Yes

MotoOffset

Color

Gobo

RGobo

Focus

Zoom

MotoReset

Yes/No

Information

LEDTemperature

Fixture useTime

XXXX

SoftwareVersion

VA X.X.X

VB X.X.X

TestMode

AutoTest

Dimmer

000 -255

LEDbrightness

Color

000 -255

Motorposition

Gobo

000 -255

Motorposition

RGobo

000 -255

Motorposition

Focus

000 -255

Motorposition

Zoom

000 -255

Motorposition

OperationMode

DMX Mode

Yes

UserMemory

Yes

PresetMemory

（PR01~PR16）

PR01~PR16

UserPrograEdit

（ET01~ET16）

Dimmer

000 -255

Strobe

000 -255

Color

000 -255

Gobo

000 -255

RGobo

000 -255

Focus

000 -255

Zoom

000 -255

KeepTime

000 –200 (0-20S)

6. DMX PROTOCOL

Function

DMXValue

Description

Dimmer

000-255

0-100%lineardimmer

DimmerFine

000-255

Dimmerin16bit

Strobe

000-007

008-255

Strobefromslowtofast

ColorWheel

000-009

Color1

010-019

Color1-Color2

020-029

Color2

030-039

Color2-Color3

040-049

Color3

050-059

Color3-Color4

060-069

Color4

070-079

Color4-Color5

080-089

Color5

090-099

Color5-Color6

100-109

Color6

110-119

Color6-Color1

120-127

Color1

128-191

Clockwiserotation fromslowtofast

192-255

Anti-clockwise rotation fromslowto fast

RotatingGoboWheel

000-015

Gobo1

016-031

Gobo2

032-047

Gobo3

048-063

Gobo4

064-079

Gobo1shake

080-095

Gobo2shake

096-111

Gobo3shake

112-127

Gobo4shake

128-189

Clockwiserotation fromfasttoslow

190-193

Stop

194-255

Anti-clockwise rotation fromfasttoslow

RotatingGobo

000-127

Goboposition

128-189

Clockwiserotation fromfasttoslow

190-193

Stop

194-255

Anti-clockwise rotation fromfasttoslow

7. TECHNICALDATA

ELECTRIC SPECIFICATIONS

Inputvoltage:100V~240VAC，50/60Hz

Inputpower:170W@220V

Maximumcurrent:0.9A

Powerfactor:PF＞0.95

LIGHTSOURCESPECIFICATIONS

Qty TX-3636W150FC120-NUVENG-A01 150WLED

ManufacturersRatedLampLife 50000hours

Power consumption 150W,1pc,White

Colortemperature 7500K

COLORS

1colorwheel(5fixedcolors+open),continualrotation, magnetsensorforpositioning

ROTATING GOBOWHEEL

1rotatinggobowheel,4 Gobos

DIMMER

Linear Dimmer from0-100%

STROBE

ElectronicStrobe0.3-25FP.Swithpulsemacros

BEAMANGLE

BeamAngle15°～45°,lineardimming

CONTROL

International standardDMX512 signalcontrolprotocol, 5-pinDMX512interfaces

Master/SlavesynchronizedMode

Stand alone mode, presetmemory,selftest mode,staticscenemode

3operationmodes(DMXmode,user memory, presetmemory)

OTHERFUNCTIONS

Wirelessreceiver

LCDdisplayinvertible

Focus

000-255

Linearfocusing

Zoom

000-255

Linearzooming

Function

000-199

200-209

Motorreset

210-255

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting Beleuchtungsausrüstung Handbücher

PR Lighting

PR Lighting AQUA 580 BWS Bedienungsanleitung

PR Lighting

PR Lighting PR-8836 Bedienungsanleitung

PR Lighting

PR Lighting PR-8835 Bedienungsanleitung

PR Lighting

PR Lighting Mega Colour 2500 Bedienungsanleitung

PR Lighting

PR Lighting AQUA 350 BEAM Bedienungsanleitung

PR Lighting

PR Lighting XR250 Bedienungsanleitung

PR Lighting

PR Lighting LS150 TREE Bedienungsanleitung

PR Lighting

PR Lighting PR-111ER MOON Bedienungsanleitung

PR Lighting

PR Lighting PR-8120 Bedienungsanleitung

PR Lighting

PR Lighting AQUA 380 BEAM Bedienungsanleitung

PR Lighting

PR Lighting CENTURY SPOT PR-2002 Bedienungsanleitung

PR Lighting

PR Lighting XL 1500 Bedienungsanleitung

PR Lighting

PR Lighting XPAR 354 Bedienungsanleitung

PR Lighting

PR Lighting ARC LED 372 Bedienungsanleitung

PR Lighting

PR Lighting XR 200 BEAM Leitfaden

PR Lighting

PR Lighting PR-2900 Bedienungsanleitung

PR Lighting

PR Lighting XR 1400 Framing Bedienungsanleitung

PR Lighting

PR Lighting Junior JNR-8142D Bedienungsanleitung

PR Lighting

PR Lighting PR-8121 Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 3000-W FRAMING Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

PR Lighting

PR Lighting XPar 360 Bedienungsanleitung

PR Lighting

PR Lighting PR-2203 XR 200 Bedienungsanleitung

PR Lighting

PR Lighting XR 230 Beam Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung