PR Lighting XR130 Beam Bedienungsanleitung

1/20

XR130 Beam

PR-2133

This product manual contains important information about the safe installation and use of this projector. Please

read and follow these instructions carefully and keep this manual in a safe place for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/20

INDEX

SAFE USAGE OF THE PROJECTOR 3

INSTALLING THE PROJECTOR 4

FITTING THE LAMP 5

POWER SUPPLY – MAINS 6

CONTROL CONNECTIONS 6

DMX TERMINATOR 7

SETUP OPTIONS-PROJECTOR CONFIGURATION 7

TO SET THE DMX START ADDRESS 7

OPERATION MENU

ERROR MESSAGE

REPLACING GOBOS 10

DMX PROTOCOL

LED INDICATION

MAINTENANCE 13

LUBRICATION 13

KEEPING THE PROJECTOR CLEAN 13

TROUBLESHOOTING 13

TECHNICAL DATA 14

ELECTRICAL DIAGRAM 17

COMPONENT ORDER CODES 18

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without notice. Whilst

every care is taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement. The

publishers cannot be held responsible for the accuracy of the information herein, or any consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good condition before

installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the unit. Any damage caused by

improper use will not be assumed by the manufacturer and / or dealer.

ACCESSORIES

These items are packed together with the projector:

Name Quantity Unit Remark

G clamps 2 Pcs

XLR connector 1 pc without DMX cable

Safety cord 1 Pc

Power Cable 1 pc

Power-Con 2 Pcs Male and Female one each

User’s manual 1 Pc

Ωclamps 2 Pcs Optional

hen unpacki

ny damage ca

he projector i

umidity and d

he projector is

he projector

entilation slots

o not project t

void direct ex

o not attempt

lectrical conn

efore installat

t is essential th

o not connect

ake sure that

nly handle th

eep the lamp

he projector s

“installing th

hields and len

y cracks or de

xterior surfac

here is no use

f you have any

lwa

s dis

ork !

g and before

sed by transpo

for indoor us

st. Do not allo

not designed

only intende

ust be install

are blocked.

e b

am onto i

osure to the li

o dismantle a

ction must onl

on, ensure that

t each project

this device to

the powe

-cor

powe

-cord b

lean. Do not t

ould always b

projector” se

shall be chan

p scratches.

temperatures

serviceable pa

questions or s

onnection

SAF

isposing of th

tation, consult

only, IP20.

contact with

r intended to b

or installation,

d in a locatio

flammable su

ht from the la

d/or modify th

be carried ou

the voltage an

r is correctly e

y other types

is never cri

the plug. Nev

uch the lamp

installed with

tion.

ed if they hav

f the luminair

ts inside the p

ggestions, don

’

rom Powe

USAG

carton check t

your dealer an

se only in dr

ater or any ot

mounted dire

operation and

with adequa

faces, minimu

p. The light is

projector in a

y qualified p

frequency of

rthed and that

f dimmer app

ped or damag

r pull out the

lass with bare

a secondary s

become visibl

after 30 minut

ojector, do not

’

t hesitate to co

when the

3/20

OF THE

ere is no trans

do not use th

locations. Ke

er liquids.

tly on to infla

aintenance b

e ventilation,

distance is 3

harmful to the

y way.

rsonnel.

ower supply

lectrical install

ratus.

d by sharp ed

lug by tugging

and.

fety fixing. A

damaged to s

s operation is

pen the housi

sult your deal

device not

PROJE

ortation dam

apparatus.

p this device

mable surface

qualified pers

t least 50cm

ye.

atch the powe

tion conforms

es. Never let

the powe

-cor

afety cord is s

ch an extent t

℃, when ste

g and never o

r or manufact

n use or b

TOR

ge before usin

way from rai

nnel.

rom adjacent

requirements

to all

elevant

he power-cord

ppli

d for this;

at their effecti

dy state is ach

erate the proje

fore cleani

the projector.

and moisture,

all surfaces.

f the projector.

tandards.

ome into contac

it should be at

eness is impai

eved 90℃,

tor with the co

or an

Should there b

excessive hea

e sure

hat n

with other cable

ached as show

ed, for exampl

ers removed.

aintenanc

4/20

INSTALL THE PROJECTOR

106

Safety Hook

Handle

Safety Cord

Digital

Control Panel

WARNING

Please run safety cord

through safety hook

Take 2 clamps and the safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to each

clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING on the underside of the base

as shown above) To pass the SAFETY CORD through the HOLES forsafety! Always ensure that the projector is firmly anchored to

avoid vibration and slipping whilst functioning. Always ensure that the structure that you are going to mount the projector to is secure and

strong enough to support the weight of a XR 130 Beam

WARNING:

1. The projector MUSTbe lifted or carried by the HANDLES instead of clamps.

2. For safety the safety cord should afford 10 times the Projector’s weight.

5/20

FITTING THE LAMP

Lock the yoke before fitting/replacing the lamp just as Shown by Figure 2, after Opening the head’s cover of a projector by loosening

4fastfit screws.

Pull out the lamp from the bottom of the head after rotating it anti-clockwise after holding the lamp’s bottom.

Installation and removal are in reverse orders.

Tighten the 4 fastfit screws after the cover is installed.

Note: don’t touch the bulb of the new lamp with bare hands so as notto impair the beam output.

Important:Always read "Instructions foruse" enclosed with the lamp.

1.Manually loosen the 2 spring screws

2.Take the lamp out after pushing

it down after loosening the 2

spring screws

PR-2133

XR 130 Beam

DMX

6/20

POWER SUPPLY-MAINS

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Before connection with mains power, make sure that the voltage and frequency marked on the rating plate of the projector match what

are supplied. It is recommended that each projector be supplied separately so that they may be individually switched on and off.

NOTE: If the fixtures’ power outputs and inputs are connected in series, please connect the first fixture’s power input with the external

power supply, and connect its power output with the second fixture’s input and so on till all the fixtures are connected. If the supplied

voltage is 200V~240V, the maximum number of fixtures connected is 10pcs. If it is 100V~120V, the maximum is 8pcs. The diameters of

the wires for the power input and output cables must be equal or bigger than 2.5 mm2.

IMPORTANT

It is essential that each projector is correctly earthed(yellow/green twin wire) and the electrical installation conforms to all

relevant standards.

CONTROL CONNECTION

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with each

wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the projector)

or 5 pin XLR plugs and sockets. The XLR's are connected as shown in the figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets

mustn’t be connected in any way other than mentioned in the above figure. The XR 130 Beam accepts digital control signals in protocol

DMX512 (1990).

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second fixture’s

DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX terminator as

shown in the figure below.

7/20

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2 and 3, which is then plugged into

the output socket on the last projector in the chain. The connections are illustrated below.

SETUP OPTIONS-PROJECTOR CONFIGURATION

Projector configuration can be set conveniently via push button and LCD display.

Launch the projector and press button ENTER for more than 5 seconds to unlock the panel, the LCD will show the function menu of the

projector, each main menu has its submenus and each submenu has a specific function. For details, please see the

“OPERATION MENU” section.

Press button UP or DOWN if you want to browse through the various Setup Options.

Press button ENTER to save your settings or enter the submenu.

Press button UP or DOWN to change values(plus or minus)

Press button FUNC, it will return to the upper menu. If button FUNC not pressed, the default will show display status automatically.

TO SET THE DMX START ADDRESS

Each XR 130 Beam must be given a DMX start address so that the correct projector responds to the correct control signals. This DMX

start address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

controller. The XR 130 Beam has 2 DMX modes. There are standard and short modes. For example standard mode has 16channels, so

set the No. 1 projector’s address 001, No. 2 projector’s address 017, No. 3 projector’s address 033,and No. 4 projector’s address is

049,and so on.

Launch the projector. Press button ENTER more than 5 seconds to unlock panel.

Press button ENTER to display DMX address;

Press button UP and DOWN, you can set the address;

Press button ENTER to confirm; after powered on next time, the default will be last value saved

Press button FUNC, it will return to the upper menu.

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain. PIN 3

PIN 2

8/20

OPERATION MENU

First Menu Secondary Menu Third Menu Fourth Menu

DMX Address

XXX

（XXX:1~497）

Short 1～501

Standard 1～497

Reset Are You Sure

Config Settings

DMX Channel Mode

（Default：Standard）

Standard16

Short 12

Loss of DMX

When DMX is Lost

Normal Time out

When DMX is Lost

Hold Last value

Lamp Control

By Control Channel

By Power On

By DMX Present

Pan Calibration 0~127

Tilt Calibration 0~127

Parameter Transm YES

Factory Settings YES

Option Settings

Color Wheel Positions

Color Positions

Steeped

Color Positions

Linear

Pan DMX Invert

OFF

Pan DMX Invert

Tilt DMX Invert

OFF

Tilt DMX Invert

Pan Tilt Swap

OFF

Pan Tilt Swap

Dimmer Invert

OFF

Dimmer Invert

Pan Angle Range 360 / 720

Defaults YES

Display Options

Language

English

Chinese

Display Mode

Display

On Always

Display

Off After Delay

Display Invert

OFF

Display Invert

Display Dimming 1~10

Display Contrast Display Contrast

XX(1~18),default 9

9/20

Information

Lamp Hours Hours：xx

Reset Lamp Hours Are You Sure

Total Hours Hours：xx

Temperature Temperature

XX℃

Software Version

Display Board Display Board=

X.X.X

Fan Board Fan Board=

X.X.X

View DMX Values DMX Channel

1=XXX

Electronic SN Electronic SN=

********

Test Modes Self Test Yes

Lamp Manual Control

Turn Lamp On Yes

Turn Lamp Off Yes

Wireless Options

(Optional)

Wireless Mode

XLR First

Wireless Mode

Wireless First

Wireless Mode

Wireless Only

Wireless Mode

XLR Only

Wireless Mode

Wireless To XLR

Un-Link Wireless YES

Operation Mode

DMX Mode YES

Master Mode

Preset Memory YES

User Memory YES

Memory Edit

Static Scene

（1~16 scenes）

Strobe

Dimmer

Color wheel

Slave Mode

Rotating

Gobo Wheel

Gobo

Rotation

Effect Wheel

Settings

Prism

Rotation

Focus

Pan Location

Pan

Tilt Location

P&T Speeds

Hold Time

10/20

ERROR MESSAGES

In the course of launch, Projector examines automatically whether there are errors and if there are, it will display

information as follows:

Head Fan 1 Fail

Head Fan 2 Fail

REPLACING GOBOS

Disconnect from power ,loosen 4 fastfit screws of the side cover, and open the cover as shown by the figure below.

Replace an old gobo of the rotating gobo wheel with a new gobo.

Tighten the 4 fastfit screws after the side cover is put back.

PR-2133

XR 130 Beam

DMX

Snap rings

Gobo

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting Beleuchtungsausrüstung Handbücher

PR Lighting

PR Lighting AQUA 380 BWS Bedienungsanleitung

PR Lighting

PR Lighting PR-2900 Bedienungsanleitung

PR Lighting

PR Lighting XL 1500 Bedienungsanleitung

PR Lighting

PR Lighting XLED 590 Bedienungsanleitung

PR Lighting

PR Lighting PR-8121 Bedienungsanleitung

PR Lighting

PR Lighting CENTURY SPOT PR-2002 Bedienungsanleitung

PR Lighting

PR Lighting PR-8920 Bedienungsanleitung

PR Lighting

PR Lighting PR-8170A Bedienungsanleitung

PR Lighting

PR Lighting TANGO FRAMING Bedienungsanleitung

PR Lighting

PR Lighting PR-6000 FRAMING Bedienungsanleitung

PR Lighting

PR Lighting PR-8846 Bedienungsanleitung

PR Lighting

PR Lighting XPar 150 Zoom Bedienungsanleitung

PR Lighting

PR Lighting XL 1500 Bedienungsanleitung

PR Lighting

PR Lighting TANGO SPOT Bedienungsanleitung

PR Lighting

PR Lighting PR-8835 Bedienungsanleitung

PR Lighting

PR Lighting CUBIX300 Bedienungsanleitung

PR Lighting

PR Lighting XLED 4007 BEAM Bedienungsanleitung

PR Lighting

PR Lighting Mega Colour 2500 Bedienungsanleitung

PR Lighting

PR Lighting PR-111ER MOON Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

PR Lighting

PR Lighting AQUA 350 BEAM Bedienungsanleitung

PR Lighting

PR Lighting AQUA 380 BEAM Bedienungsanleitung

PR Lighting

PR Lighting Junior JNR-8142D Bedienungsanleitung

PR Lighting

PR Lighting CHAMELEON PR-2012H Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung