PR Lighting PR-111ER MOON Bedienungsanleitung

MOON

PR-111ER

This product manual contains important information about the safe installation and

use of this projector. Please read and follow these instructions carefully and keep

this manual in a safe place for future reference.

PR LIGHTING LTD.

No. 571 Yingbin Road, Dashi Panyu, Guangzhou, 511430 China

http://www.pr-lighting.com

Moon manual.doc

2/14

SECTION PAGE

SAFE USAGE OF THE PROJECTOR 3

INSTALLING THE PROJECTOR 4

FITTING THE LAMP 4

POWER SUPPLY –MAINS 5

OPERATION 5

STAND-ALONE MODE 6

XLR CONNECTIONS AND TERMINATOR 6

MASTER/SLAVE SYNCHRO MODE 7

CONTROLLER MODE -DMX OPERATION 8

DMX CONTROL CHANNEL FUNCTIONS 9

MAINTENANCE 9

CHANGING THE GOBOS 10

LUBRICATION 10

KEEPING THE PROJECTOR CLEAN 11

TROUBLESHOOTING 11

TECHNICAL DATA 11

ELECTRICAL DIAGRAM 12

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change

without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the

course of product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any

consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit is in

good condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do

not use the unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.

THESE ITEMS ARE PACKED TOGETHER WITH THE PROJECTOR

Mounting Bracket (1 PCS)

M6 Knob for mounting bracket (2 PCS)

Safety cord (1 PCS)

Power-cord (1PCS)

XLR plug (1 PCS)

XLR socket (1 PCS)

This manual (1PCS)

Thank you for purchasing the MOON,PR-111ER.

The MOON is an innovative projector with an elegant housing made from high intensity and heat-

resistant complex plastic. The projector complies to CE norms and standards and uses international

protocol DMX-512. The unit can be controlled by sound, auto programmes or a controller, it may be

used as a stand-alone unit, so it is suitable for many different applications.

The MOON features 10 dichroic colours which can produce a rainbow effect when the colour-wheel

rotates quickly and 8 rotatable and interchangeable gobos, and an independently adjustable

strobe/shutter. The unit has an auto thermal cut-off for working safety. It can be setup easilyvia the

touch-switches and the digital display.

ACCESSORIES

INDEX

INTRODUCTION

Moon manual.doc

3/14

The following points are important for safety as well as for the smooth

installation and performance of the unit.

When unpacking and before disposing of the package check there is no transportation damage

before using the projector. Should there be any damage caused by transportation, consult your

dealer and do not use the unit. Keep the package well for your possible future transportation.

The projector is for Indoor use only, IP20. Use only in dry locations. Keep this device away from rain

and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other fluids,

or metallic objects.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Do not project the beam onto inflammable surfaces, minimum distance is 3m. 3m

Avoid direct exposure to the light from the lamp. The light is harmful to the eye.

Do not attempt to dismantle and / or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power

requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all

relevant standards.

Do not connect this device to any dimmer pack.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-

cord come into contact with other cables. Only handle the power-cord by the plug. Never pull out the

plug by tugging the power-cord.

Keep the lamp clean. Do not touch the lamp glass with bare hands.

The lamp used in this projector is an MSD 250W discharge lamp. After being switched off don’t

attempt to restart the projector until lamp has cooled, this will require approx 15 minutes. Switching

the lamp on and off at short intervals will reduce the life of both the lamp and the projector.

Occasional breaks in operation will prolong the life of both the lamp and the projector.

Never run the projector without a lamp.

There are no user serviceable parts inside the projector, do not open the housing and never operate

the projector with the covers removed.

Always disconnect from the mains, when the device is not in use or before cleaning it

or before attempting any maintenance work.

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

SAFE USAGE OF THE PROJECTOR

Moon manual.doc

4/14

Mount the bracket provided on the body of the projector using the 2 M6 knobs provided, and then

suspend the projector via a fixing hole on the bracket using anM12 size bolt and a nut. When you

want to adjust the angle of the body of the projector, you only loosen the 2 M6 knobs carefully and

then adjust the angle of the body. Always ensure that the projector is firmly positioned to avoid

vibration and slipping, and always ensure that the structure to which you are attaching the projector is

secure and is able to support a weight of 10Kg for each MOON.

For safety the unit should have a secondary fixing with the safety cord provided through the hole on

the upper unit.

Open the lamp access hatch at the bottom of the projector by loosening the 2 M4 screws as shown

above.

Take out the lamp-bracket from the inside of the projector by loosening the 2 M4 screws.

Insert the lamp in the lamp holder.

Install the lamp-bracket on the position slot well and then tighten the 2 M4 screws.

Close the lamp access hatch again, and then tighten the 2 M4 screws.

NOTE: The MSD series are high pressure lamps with external igniters . Care should always be

taken when handling these lamps. Always read the manufacturers "Instructions for use" enclosed

with the lamp.

FITTING THE LAMP

INSTALLING THE PROJECTOR

Moon manual.doc

5/14

Use the plug provided to connect the

mains power to the projector paying

attention to the voltage and frequency

marked on the panel of the projector. It

is recommended that each projector is

supplied separately so that they may be

individually switched on and off.

IMPORTANT

It is essential that each projector is

correctly earthed and that electrical

installation conforms to all relevant

standards. Power consumption of each

MOON is 280W at 220V.

The projector may be controlled by sound, auto

programmes or a controller, and it may be operated in

Stand-Alone automatic mode, in Master/Slave synchro

mode or in Controller mode. With the touch-switches

and the digital display.The DMX start address can be

easily set and the various setup options may be

configured.

TO SET THE DMX START ADDRESS

The display shows the DMX start address after the

projector is switched on (if you have already set the

DMX start address and saved it, the screen will display the last setting).

Press the UP or DOWN buttons to select the required DMX start address in the display.

Confirm your choice by pressing the ENTER button, this will save and set the DMX start address.

The display will show the latest setting each time when the projector is powered up.

In Stand-Alone mode, the DMX start address can be set at random.

In the Controller mode and Master/Slave mode, the DMX start address must be set correctly. (Refer

to “Controller mode” and “Master/Slave mode” sections).

SETUP OPTIONS -PROJECTOR CONFIGURATION

To browse through the various Setup Options, press the FUNC button consecutively. There are 11

option codes (1~9 and A, b), each code has a specific function. The functions provided are listed in

the following table.

Once you have selected the desired operation code, press the key UP or DOWN to select “n”

(means OFF) or “y “ (means ON). N = ON, Y = YES.

Press the key ENTER to save the selected function and configuration. If the display is showing “y”,

then the setting has been enabled. In the same way, if it was showing “n” when you pressed ENTER

the option has been disabled.

The green LED will flash during this operation.

OPERATION

POWER SUPPLY -MAINS

Moon manual.doc

6/14

SETUP OPTIONS

CODE CHOICE FUNCTION

YPan inversion enable-Pan is inverted

1NPan inversion disable-Pan is normal

YTilt inversion enable-Tilt is inverted

2NTilt inversion disable-Tilt is normal

YSound activation enable

3NSound activation disable

YAutomatic programmes enable

4NAutomatic programmes disable

5Reserved for possible future development

6Reserved for possible future development

YReset enable

7NReset disable

8When enable, colours are linear change

9Reserved for possible future development

AReserved for possible future development

BReserved for possible future development

Without connecting the controller, with the setup option 3 (sound activation) or 4 (auto programmes)

enable, the projector will run in Stand-Alone mode.

If you enable a combination of setup options 3 (sound activation) and 4 (auto programmes), the

projector will run in auto programmes.

You may set the DMX start address randomly in Stand-Alone mode.

When the projector is activatived by sound, the red indicator will flash according to the rhythm of the

music. And when the projector is running in auto programmes, the indicator will be constantly red.

XLR CONNECTORS

Connection between controller and projector and between one projector and another must be made

with 2 core screened cable, with each core having at least a 0.5mm diameter. Connection to and

from the projector is via cannon 3 pin XLR plugs and sockets which are included with the projector.

The XLR's are connected as shown in the table above.

Note: Care should be taken to ensure that none of the connections touch the body of the plug or each

other. The body of the plug is not connected in any way. The MOON accepts digital control signals in

standard DMX512 (1990) format.

STAND-ALONE MODE

XLR CONNECTORS AND TERMINATOR

Moon manual.doc

7/14

5-PIN AND 3-PIN CONVERSION

MOON uses 3-pin XLR plug / socket. If your controller uses 5-pin XLR plug / socket, you should

convert 5-pin plug / socket into 3-pin socket / plug as shown below.

DMX TERMINATOR

In the Controller mode or Master/Slave mode, the DMX output has to be connected with a DMX

terminator at the last fixture in the chain. This prevents electrical noise from disturbing and corrupting

the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2

and 3, which is then plugged into the output socket on the last projector in the chain. The connections

are illustrated below.

Without using a controller, many projectors can run synchronously in the Master/Slave mode by

linking them with each other.

Select one projector as the master with setting the DMX start address at random. Regard the other

projectors as the slaves setting all DMX start address “001”.

Connect the master’s output to the first slave’s input, and connect the first slave’s output to the

second slave’s input. The rest may be deduced by analogy. Eventually connect the last slave’s output

to a DMX terminator as shown in the figure below.

MASTER / SLAVE MODE

Moon manual.doc

8/14

In the Master/Slave mode, you may run the master via the auto programmes having been set in the

master or via sound activation through MIC inside the master, and the slaves will run synchronously

with the master.

In the Master/Slave mode, when the master is a combination of setup 3 (sound activation) and 4

(auto programmes), the projectors will run auto programmes.

When the master runs in auto programmes, the master’s red indicator is constantly on but the slaves’

red indicators flash.

Each MOON must be given a DMX start address so that the correct projector responds to the correct

control signals. This DMX start address is the channel number from which the projector starts to

“listen” to the digital control information being sent out from the controller. The MOON has 6 channels,

so set the No.1 projector’s address 001, No.2 projector’s address 007, No.3 projector’s address 013,

No.4 projector’s address 019, and so on.

Certainly, you may use formulation: address=channels x (projector No. –1) +1

For example, for the No.4 projector’s start address, you should calculate according to formulation: 6 x

(4 –1) +1 = 19. So you set the No.4 projector start address 019.

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the

second fixture’s input. The rest may be deduced by analogy. Eventually connect the last fixture’s

output to a DMX terminator as shown in the figure below.

When a DMX 512 signal is received the red indicator will flash. When not receiving a DMX signal the

green and red indicators will be off.

CONTROLLER MODE -DMX 512 OPERATION

Moon manual.doc

9/14

The MOON uses 6 channels with standard DMX 512 protocol. They are listed in the following table.

CHANNEL DMX VALUE DESCRIPTION

0-17 White

18-35 Red

36-53 Yellow

54-71 Orange

72-89 Blue

90-107 Green

108-125 Cyan

126-143 Ultraviolet

144-161 Pink

162-177 Light green

Colour

178-255 Change of colours from slow to fast till rainbow effect

0-31 Open / Clear

32-63 GOBO 1 (Triangle)

64-95 GOBO 2 (Multi-circle)

96-127 GOBO 3 (Windmill)

128-159 GOBO 4 (Stars)

160-191 GOBO 5 (Flying-swallows)

192-223 GOBO 6 (Swirl)

Gobo

224-255 GOBO 7 (Radiation)

0-14 Black-out

15-29 Open

30-250 Strobe adjust from slow to fast (1 to 7 flashes per sec.)

Shutter/Strobe 251-255 Open

0-4Stop

5-120 Rotate in opposite direction from slow to fast reaching

114 rpm

121-139 Stop

Gobo rotation

140-255 Rotate from slow to fast reaching 114 rpm

5Pan 0-255 Pan movement from 0°to 175°

6Tilt 0-255 Tilt movement from 0°to 80°

If the projector’s lens becomes damaged or broken it should be replaced. If the lamp becomes

damaged or deformed in any way it must be replaced. If the light from the lamp appears dim this

would normally indicate that it is reaching the end of its life and it should be changed at once, old

lamps run to the extremity of their life can explode. If the projector does not function, check the fuse

on the power socket of the projector, they should only be replaced by fuse of the same specified

value 6.3A/250V (fast blow, 5mmx20mm). On the main PCB inside the projector there is also a fuse

rated 4A/250V (fast blow, 5mmx20mm). Should these be damaged call a qualified technician before

replacement. The projector has thermal protection device that will switch off the projector in case of

overheating, should this operate, check that the fans are not blocked, and if they are dirty clean them

before switching on the projector again. Check that the fans are operational, if not call a qualified

technician.

Any maintenance work should only be carried out by a qualified technician.

DMX CONTROL CHANNEL FUNCTIONS

MAINTENANCE

Moon manual.doc

10/14

Carefully lift off the upper plastic body which has the name label sticker on it by loosening the 6

screws.

Using a small screwdriver remove the gobo retaining spring.

Insert the gobo into position, and then insert the retaining spring.

Install the upper cover and tighten the 6 screws.

To ensure the continued smooth rotation of the rotating gobos it is recommended that the bearings

for rotation-gobo-gears are lubricated periodically, preferably every three months. Use only high

working temperature low viscosity oil, a syringe with a fine needle is the easiest way to introduce the

oil to the bearings around each gobo. Do not over lubricate as this will cause spillage when the gears

rotate.

To ensure the reliability of the projector it should be kept clean. It is recommended that the fans

should be cleaned every 15 days. The lens and dichroic colour filters should also be regularly

cleaned to maintain an optimum light output. Do NOT use any type of solvent on dichroic

colour filters.

Cleaning frequency depends on the environment in which the fixture operates: damp, smoke or

particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics. A soft cloth

and typical glass cleaning products should be used in cleaning. It is recommended to clean the

external optics at least once every 20 days and clean the internal optics at least once every 30/60

days.

Do not use any organic solvent, e.g. alcohol, to clean the housing of the projector.

KEEPING THE PROJECTOR CLEAN

CHANGING THE GOBOS

LUBRICATION

Inhaltsverzeichnis

Andere PR Lighting Beleuchtungsausrüstung Handbücher

PR Lighting

PR Lighting XLED 4007 BEAM Bedienungsanleitung

PR Lighting

PR Lighting PR-2330 Bedienungsanleitung

PR Lighting

PR Lighting XL 1500 Bedienungsanleitung

PR Lighting

PR Lighting Junior JNR-8142D Bedienungsanleitung

PR Lighting

PR Lighting ARC LED 372 Bedienungsanleitung

PR Lighting

PR Lighting PR-8920 Bedienungsanleitung

PR Lighting

PR Lighting XL WASH 700 Bedienungsanleitung

PR Lighting

PR Lighting AQUA 350 BEAM Bedienungsanleitung

PR Lighting

PR Lighting DESIGN 150 Bedienungsanleitung

PR Lighting

PR Lighting XPar 150 Zoom Bedienungsanleitung

PR Lighting

PR Lighting PR-8121 Bedienungsanleitung

PR Lighting

PR Lighting AQUA 580 BWS Bedienungsanleitung

PR Lighting

PR Lighting XR130 Beam Bedienungsanleitung

PR Lighting

PR Lighting PR-8846 Bedienungsanleitung

PR Lighting

PR Lighting XLED 590 Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

PR Lighting

PR Lighting PR-2900 Bedienungsanleitung

PR Lighting

PR Lighting PR-2203 XR 200 Bedienungsanleitung

PR Lighting

PR Lighting PR-8170A Bedienungsanleitung

PR Lighting

PR Lighting TANGO SPOT Bedienungsanleitung

PR Lighting

PR Lighting XR 1400 Framing Bedienungsanleitung

PR Lighting

PR Lighting CHAMELEON PR-2012H Bedienungsanleitung

PR Lighting

PR Lighting XR 230 Beam Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung