PR Lighting XR250 Bedienungsanleitung

XR 250（BEAM）

PR-2206

This product manual contains important information about the safe installation and use of this projector.

Please read and follow these instructions carefully and keep this manual in a safe place for future reference.

PR LIGHTING LTD.

http://www.pr-light ing.com

2/22

INDEX

SAFE USAGE OF THE PROJECTOR 3

INSTALLING THE PROJECTOR 4

FITTING LAMP 4

POWER SUPPLY – MAINS 5

CONTROL CONNECTIONS 5

DMX TERMINATOR 6

SETUP OPTIONS-PROJECTOR CONFIGURATION 6

TO SET THE DMX START ADDRESS 6

STAND-ALONE MODE 7

MASTER/SLAVE MODE 7

OPERATION MENU 8

DMX PROTOCOL 12

MAINTENANCE 15

LUBRICATION 16

KEEPING THE PROJECTOR CLEAN 16

TROUBLESHOOTING 16

TECHNICAL DATA 17

ELECTRICAL DIAGRAM 20

COMPONENT ORDER CODES 21

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without notice. Whilst

every care is taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement. The

publishers cannot be held responsible for the accuracy of the information herein, or any consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good condition

before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the unit. Any damage caused

by improper use will not be assumed by the manufacturer and / or dealer.

ACCESSORIES

These items are packed together with the projector:

Name Quantity Unit Remark

G clamps 2 Pcs

XLR cable 1 Pc with plug

Safety cord 2 Pcs

This manual 1 Pc

Ω clamps 2 Pcs Optional

3/22

SAFE USAGE OF THE PROJECTOR

When unpacking and before disposing of the carton check if there is no transportation damage before using the projector. Should there

be any damage caused by transportation, consult your dealer and do not use the apparatus.

The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture, excessive heat,

humidity and dust. Do not allow contact with water or any other liquids.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces. Be sure that no

ventilation slots are blocked.

Do not project the beam onto inflammable surfaces, minimum distance is 12m. 12m

Avoid direct exposure to the light from the lamp. The light is harmful to the eye.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact with other cables.

Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.

Keep the lamp clean. Do not touch the lamp glass with bare hand.

The projector should always be installed with a secondary safety fixing. A safety cord is supplied for this; it should be attached as

shown in “installing the projector” section.

The lamp used in this projector is a discharge lamp. After switching off don’t attempt to restart the projector until lamp has cooled, this

will require approx 15 minutes. Switching the lamp on and off at short intervals will reduce the life of both the lamp and the projector.

But occasional breaks will prolong the life of the lamp and projector.

Never run the projector without a lamp.

The lamp shall be changed if it has become damaged or thermally deformed or reached its life limit.

Shields and lens shall be changed if they have become visibly damaged to such an extent than their effectiveness is impaired, for

example by cracks or deep scratches.

Exterior surface temperatures of the luminaire after 5 minutes operation is 35℃, when steady state is achieved 55℃,

There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the covers

removed.

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

Always disconnect from the mains, when the device is not in use or before cleaning it or before

attempting any maintenance work !

4/22

INSTALL THE PROJECTOR

Take 2 clamps and 1 safety cords out from the package and mount 2 clamps on the underside of fixture with 4 retainers attached to

each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING on the underside of

the base as shown above) Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning.

Always ensure that the structure that you are going to mount the projector is secure and is strong enough to support the weight of the

fixture.

WARNING

1. The projector MUST be lifted or carried by the HANDLES instead of clamps.

2. For safety the safety cord should support 10 times of the unit’s weight.

FITTING THE LAMP

Unplug the projector from power before lamp

installation or replacement and wait for it to cool.

Lock the yoke before fitting/replacing the lamp.

Loosen 8 fast-fit screws and remove the back cover,

you can see the structure as shown in the figure 2..

After unplug the power wires, hold the end of the

lamp and push it as directed by the arrow resulting in

the other end of the lamp unblocked ,then pull the

lamp out. Before installing new lamp, plug the power

wires for the lamp tightly. Installation of the lamp is

an reverse sequence to the pull-out.

Fit new lamp and close the back cover by fastening 8

fast-fit screws. Note: don’t touch the bulb of the new

lamp with bare hand so as not to influence the beam

output; Do not harm the sticking out point of the lamp during its installation.

WARNING: Care should always be taken when handling these lamps. Always read the manufacturers "Instructions for

use" enclosed with the lamp.

CONTROL

PANEL

CLAMP

HANDLE

SAFETY CORD

106

WARNING

To pass 1 SAFETY CORD

through 2 holes for safety

FAST-FIT SCREWS

LAMP

5/22

POWER SUPPLY-MAINS

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel

of the projector. It is recommended that each projector be supplied separately so that they may be individually switched on and off.

IMPORTANT

It is essential that each projector is correctly earthed(yellow/green twin wire) and the electrical installation conforms to all

relevant standards.

CONTROL CONNECTION

Connection between controller and projector and between one projector and another must be made with a 2 core-screened cable, with

each core having at least a 0.5mm diameter. Connection to and from the projector is via cannon 3 pin (which are included with the

projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown in the figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of the plug is not

connected in any way other than as shown above. The projector accepts digital control signals in protocol DMX512 (1990).

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input and connect

the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown in the figure below.

TO CONTROLLER

DMX512 DMX IN DMX OUT

TO TERMINATER

DMX IN DMX OUT DMX IN DMX OUT

6/22

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120 (ohm) resistor connected across pins 2 and 3, which is then plugged

into the output socket on the last projector in the chain. The connections are illustrated below.

SETUP OPTIONS-PROJECTOR CONFIGURATION

Projector configuration can be set conveniently via switch button and LCD display. Turn the projector on and the LCD display will

show DMX address you set and save last time and it can be reset and saved again as you please.

Launch the projector. Press button ENTER more than 5 seconds to unlock panel. After this, the display shows the projector’s function

menu and each option has its own sub-menus. Each menu stands for special function, see details as follows.

Press button UP or DOWN if you want to browse through the various Setup Options.

Press button ENTER to save your settings or enter the next menu. Press button UP or DOWN to change the values(plus or minus)

Press button FUNC, it will return to the upper menu one by one. If the button not pressed, defaulted will show display status

automatically.

TO SET THE DMX START ADDRESS

Each projector must be given a DMX start address so that the correct projector responds to the correct control signals. This DMX start

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

controller. XR 250 BEAM has2 DMX modes. There are short and standard modes . For example standard mode have 19 channels, so

set the No. 1 projector’s address 001, No. 2 projector’s address 020, No. 3 projector’s address 039, No. 4 projector’s address 058, and

so on.

Launch the projector. Press button ENTER more than 5 seconds to unlock panel.

Press button ENTER to display DMX address;

Press button UP and DOWN, you can set the address;

Press button ENTER to confirm; after powered next time, It will display latest values.

Press button FUNC, it will return to the upper menu one by one.

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

7/22

STAND-ALONE MODE

Operate the projector without connecting a controller, enable the master mode in the operation panel, the projector

will run in Stand-Alone mode automatically.

MASTER/SLAVE MODE

Without using a controller, many projectors can run synchronously in the Master/Slave mode by linking them with

each other. Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input

and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown in the figure

below. Then the first one is the master with setting options as master mode enabled, and others are slaves.

Start Address for all slaves is 001. The Master can run at any mode for the Master and Slaves run at the corresponding

mode compared to the Master.

After powered , the group will run at Master/Slave Mode.

INPUT OUTPUT

MASTER SLAVE SLAVE

INPUT OUTPUT INPUT DMX TERMINATOR

8/22

OPERATION MENU

1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL

PortSet

DMX Address Set 0 1-512 381

Universe Set 1 0-5120 382

IP Address Set 2

IP1 383 0-255

IP2 384 0-255

IP3 385 0-255

IP4 386 0-255

Subnet Mask Set 3

SubnetMask1 387 0-255

SubnetMask 2 388 0-255

SubnetMask 3 389 0-255

SubnetMask 4 390 0-255

Gatesay IP Set 4

Gateway IP1 391 0-255

Gateway IP2 392 0-255

Gateway IP3 393 0-255

Gateway IP4 394 0-255

Reset Are You Sure 6

Config Set

DMX Mode

（Default：Standard）

Standard 31 1

Extended 38 2

Short 25 3

Other XX 4

LampControlSe

（Default：By Control

Channel）

ByControlChann 5

ByPowerOn 6

ByDmxPresent 7

Loss of DMX

（Default：Turn-off ）

Normal Time Out 8

Hold Last Value 9

Wireless Mode

（Default：XLR First）

XLR First 13

XLR Only 14

Wireless Only 15

Wireless First 16

WirelessTo XLR 17

Master/Slave

（Default：SLAV）

Slave 21

Master 22

Display Mode

（Default：Off after delay）

OffAfterDelay 23

On Always 24

DisplayContrast 20 XX 41

0-31

Pan amend 21 XXX 42

9/22

127

Tilt amend 22

XXX 43

0-127

Unlink Wireless 23 YES 51

ResetLampHours 24 YES 52

ResetUserData 25 YES 53

ResetOptionSet 26 YES 54

FactorySettings 27 YES 55

ParameterTransm 28 YES 56

Option Set

Color Positions31

（Default：Step）

Step 61

Linear 62

F- Gobo Positions32

（Default：Step）

Step 63

Linear 64

Pan DMX Invert

（Default：Off）

Off 65

On 66

Tilt DMX Invert34

（Default：Off）

Off 67

On 68

Pan Tilt Swap35

（Default：Off）

Off 69

On 70

Dimmer Invert36

（Default：Off）

Off 71

On 72

Information

Lamp Hours 51 XXXX 91

Power On Hours 52 XXXX 92

Software Version 53

MainBoard X.X.X93

Pan&Tilt X.X.X94

Driver 1 X.X.X 95

Fan Board X.X.X 96

Fan Board X.X.X 97

Fan Board X.X.X98

Temperature 54

Head Sensor 101

Display Board 102 XX

Pan and Tilt 103 XX

Driver Board 1 104 XX

Fan Board 105 XX

View DMX Values 55 Channel XXX=XXX 111

Electronic SN 56 SN=XXXXXXXXXXXX 112

RDM Device Lable 57

Version X.X 113

Fan Err View58 Fan 1 OK/Error 114

Fan2 OK/Error 115

Positions Sensor59 X Optocoupler Ok/Er 131

Y Optocoupler Ok/Er 132

10/22

X Hall Ok/Er 133

Y Hall Ok/Er 134

Prism Hall Ok/Er 135

Effect Roat Hall Ok/Er 136

Effect Hall Ok/Er 137

Focus Hall Ok/Er 138

R- gobo Hall Ok/Er 139

Gobo- R Hall Ok/Er 140

F- gobo Hall Ok/Er 141

Color Hall Ok/Er 142

Test Mode

Self Test61 YES 161

Strobe62

Open 162

Strobe1 163

Strobe2 164

Colour Wheel 63

White 165

Color1- Color13 166-178

Rotating 179

Revers Rotating 180

Fixed gobo65

White 190

F-gobo 1- F-gobo 14 191-204

Rotating 205

Revers Rotating 206

FG shake1-14 207-220

Rotating gobo1 66

White 221

R1-gobo 1- 12 222-233

Rotating 234

Revers Rotating 235

R1G shake1-12 236-247

Gobo Rotating1 67

Stop 251

Rotating 252

Revers Rotating 253

Effec 70

White 274

Prism 275

frost 276

Row Mirror 277

Effec Rotating 71

Stop 278

Rotating 279

Revers Rotating 280

Prism 2 72 No 281

Have 282

Prism2 Rotating 73 Stop 283

Rotating 284

Inhaltsverzeichnis

Andere PR Lighting Beleuchtungsausrüstung Handbücher

PR Lighting

PR Lighting XPar 150 Zoom Bedienungsanleitung

PR Lighting

PR Lighting AQUA 580 BWS Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

PR Lighting

PR Lighting XR 200 BEAM Leitfaden

PR Lighting

PR Lighting XL 1500 Bedienungsanleitung

PR Lighting

PR Lighting Mega Colour 2500 Bedienungsanleitung

PR Lighting

PR Lighting PR-8120 Bedienungsanleitung

PR Lighting

PR Lighting XL WASH 700 Bedienungsanleitung

PR Lighting

PR Lighting CENTURY SPOT PR-2002 Bedienungsanleitung

PR Lighting

PR Lighting TANGO FRAMING Bedienungsanleitung

PR Lighting

PR Lighting LS150 TREE Bedienungsanleitung

PR Lighting

PR Lighting XR130 Beam Bedienungsanleitung

PR Lighting

PR Lighting PR-8121 Bedienungsanleitung

PR Lighting

PR Lighting PR-2203 XR 200 Bedienungsanleitung

PR Lighting

PR Lighting XLED 590 Bedienungsanleitung

PR Lighting

PR Lighting PR-8836 Bedienungsanleitung

PR Lighting

PR Lighting XPAR 354 Bedienungsanleitung

PR Lighting

PR Lighting PR-8835 Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 1500 SPOT Bedienungsanleitung

PR Lighting

PR Lighting AQUA 380 BWS Bedienungsanleitung

PR Lighting

PR Lighting PR-8170A Bedienungsanleitung

PR Lighting

PR Lighting CHAMELEON PR-2012H Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 3000-W FRAMING Bedienungsanleitung

PR Lighting

PR Lighting PR-2330 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung