PR Lighting LS150 TREE Bedienungsanleitung

LS150TREE

PR-6821

The user manual contains important information about the safe installation and use of a projector. Please read

andfollowtheseinstructions carefullyandkeepthemanual in asafe placeforfuture reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

INDEX

1.SAFETYANDWARNINGS

2. INSTRUCTIONS

●CLEANINGAND MAINTENANCE

●TROUBLESHOOTING

3.APPEARANCE

4. INSTALLATION

●RIGGING

●PLACEAUNITONAFLATSURFACE

●TRANSPORTATION

●POWERCONNECTIONS

●DMXCONTROLCONNECTION

●DMXTERMINATOR

5. SETUPANDCONFIGURATION

●FRONTPANELOPERATION

●DMXSTARTADDRESS

●STAND-ALONEMODE

●MASTER/SLAVEMODE

6.OPERATIONMENU

7. DMXPROTOCOL

8.TECHNICALDATA

9.CIRCUITDIAGRAMANDPCBCONNECTIONS

●CIRCUITDIAGRAM

●PCB CONNECTIONS

10.COMPONENTORDERCODES

ACCESSORIES

The followingitemsaresuppliedwith theprojectorand pleasecheck:

Name

Quantity

Unit

Remark

Clamps

Powercord

XLR LoopCable

Set

Safetycord

User manual

Transparent Cover+seal+ screws×6

Set

Optional

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to changewithout notice.

Whilst every care is taken in the preparation of the manual we reserve the right to change specifications in the course of product

improvement.Thepublisherscannotbeheldresponsiblefortheaccuracyof theinformationherein, oranyconsequencearising fromthem.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good

conditionbeforeinstallationand use.Shouldthere beany damage caused bytransportation, consultyourdealerand donot usetheunit.Any

damagecausedbyimproperusewillnotbeassumed by themanufacturerand/ordealer.

Any future technical change in the user manual won’t be with any further notice.

Note: Forthe productsmade by GuangzhouPRlighting Ltd, thewarrantyfor the wholeproduct is one year starting fromthe delivery date

butthelight sourceisnotwithinthewarranty.

1. SAFETYANDWARNINGS

NOTE

Before a projector’s installation, power-on,operationandmaintenance,pleasecarefullyread

thesafetyinformationhereinafter!

Thefollowingsafety signsareusedinthe usermanual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Flames

High

Temperature

● When unpacking , check if there is transportation damage before using the projector. Should there be

anydamagecausedbytransportation,consultyourdealeranddonotuseit.

●The manufacture is not responsible for loss caused by the user not following the manual or changing the

projector ashe/shelikes

●Please be noted that the damage caused by changing the projector at willisnotwarranted.

●Do nothesitate tocontact thedealerorthemanufacturer ifanyquestionsor advice.

●The unit can be used indoors and outdoors and for its IPrating .please refer to Technical Data section of this user

manual.

● Useonlyindrylocations. Keep this unit awayfromrain andmoisture,excessiveheat,humidityand dust. Donot

allowcontactwith wateroranyotherliquids.

●It’s forbidden to make theunit withlowerprotectionleveldirectlyorindirectlycontactwater orother liquids.

●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while

beingoperated

●The projector is only intended for installation, operation and maintenance by qualified personnel. And the

operationmuststrictly followtheproceduresinthemanual

●No repairable parts in theprojector and do notopencoversfor maintenancebyyourself.

●Don’t look straightly into the lightsourcesespeciallyfor epileptics,otherwise eyeswillbeburned.

●Do not connect this device to any typeofdimmerpack

●After lamp switched on, the minimumdistancebetweentheprojectorandilluminated surfaceis1.5m

●lens and other optical parts shall be replaced immediately if they have deformed or been damaged, otherwise the

lightoutputwillbecompromised.

●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a

projector whilecovers(housing)areoff

●Keep the lamp clean and do not touch it with bare hands.

●While operating it, wear protective items.

●Any electrical connection must be carried out by a qualified person .

●Before installation, please confirm the voltage supplied matches what is required for the projector

●Each projector must be properlyearthedandinstalledasper relatedelectricalstandards.

●Do not use power cord with its insulator damaged and connect the power cord with other cables.

●If the projector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it forcefully or

bypullingthe powercable.

●All powercords mustconformtorelatedsafetyandregulations

●While beingoperated,theprojectorshould notbeunderrainsorinhumidity.

●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other

electricalparts’ lifewillbeshortened .

●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety cord

suppliedthroughthe safetycord holes forsafetysupport.

●Before any installation, maintenanceand cleaningwork,please ensuretheprojectoris disconnectedfrompower

mains.

●Under normal temperature, the temperature of the housing will be 55℃; after being stable, the unit’s

surfacetemperature willbe70℃

●While the lamp is stricken for the first time,there will be smoke and strange smell. It’s normal and does not

meantheprojectorhassome defects.

●While operated, do not touch the metallic housing. It is very hot during operation.

●Do not mount the projector directly on inflammable surface.

●Do not project the beam straightly on combustible items and the minimum distance between the projector

and illuminateditems is10m.

●A projector should be installed with good ventilation and the minimum distance between the projector and

wallsis50cm.Atthesame time,pleaseensurethefansand airinletsandoutlets areworkable.

2. INSTRUCTIONS

●CLEANINGANDMAINTENANCE

For the units with optical lens, because of the accumulation of the smoke, oil and dust on lens, the light output will be

compromised. For the reliable use of the unit, it is very necessary to keep it clean. The unit is IP65 rating waterproof device.

Unless approval by some professional technician for necessary internal component replacement, it’s forbidden to dismantle the

unit.

Cleaning frequencyis to bedecided by operations and its environment. Use soft cloth and normaldetergent for glass for cleaning

work. It’s advised external optical system be cleaned every 20days. Keep lens clean and do not touch optical parts with bare

hands.

●Beforeanymaintenance and cleaning,pleaseensuretheprojectisoffthepower

●Onlyqualifiedpersonisallowedtodo maintenance

●During maintenance andbeforemaintenance, theprojector mustbeoff power.

●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens whether

itrunsor not

●Do not use alcohol or other organic solvent to clean the housing to avoid damage.

●Do not use any solvent with chemical elements to clean color filters or hot mirror.

●TROUBLESHOOTING

PROBLEM

ACTION

The projector doesn’t switch on

Checkthepowercordconnection

Power Switch fails or is not connected well, call a professional

technicianforrepairingandchecking

Control board is not connected normally, call a professional technician

forrepairingandchecking,

The projectcanbe turned on,buttheLEDlamps

can’t be on

LED lamp board is notconnected well, call a professional technician for

repairingand checking

The LED lamps canbeon,butnotcontrolled

byDMX

CheckifDMXStartAddressisproperlyset

CheckifXLRcablefails ornot

Thebrightnessdecreasesobviously

Ambient temperature is too hot which makes the projector too hot,

pleasetakeappropriate ventilationmeasures

3. APPEARANCE

4. INSTALLATION

5. ●RIGGING

Take 1 clamp and 1 safety cord out from the package and tightenthe clamp with the arm, and thenmount the whole uniton the truss,

tighten the clamp’s retainers to keep the unit stable. (See the WARNING on the underside of the base as shown above) To pass the

SAFETYCORDthroughtheARM forsafety!Alwaysensurethatthe unit is firmlyanchoredto avoidvibrationand slippingwhilst

Arm

Safety Clamp

Warning

For safety, please

run the safety cord

through the safety cord

hole and ensure it is

tightened .

arm

body

functioning. Always ensurethat the structure that you are going to mount the unit to is secure and strong enough to support the weight

oftheunit Loosen thebigknob and adjust the head’s angle for the effect desired and the tighten it. The installation is completed.

(iftheunitiswitwirelesscontrol, whilebeing hung,theantennashould facedown)

●PLACEAUNITONAFLATSURFACE

Before placing a unit on a flat surface, loosen the small knob with the support and make the angle between the arm and the support

60degrees.Tightenthesmallknob. Loosenhebig knobandadjusttheanglebetweenthe armand unitasdesiredand thentightenit.

.(If the unit is with wireless control,afterthe unit isplaced on aflat surfacethe antenna should face up)

●TRANSPORTATION

Beforetransportation,tightenboth knobs after the armandsupport are overlapped.

WARNING:

●TheprojectorMUSTbe lifted orcarriedbytheHANDLESinsteadofclamps.

●.For safety the safety cord should afford 10 times the Projector’s weight.

●POWERCONNECTION

Connectthepower cordas follows:

L(live)=brown

E(earth) =yellow/green

N(neutral)=blue

Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that each

projector beconnectedwithpowerseparatelyso thattheymaybeindividuallyswitchedonandoff.

Note: If projectors are connected in series, please connect POWERIN port of the 1st projector with the Power Mains, then

connectitsPOWEROUTwithPOWERINof the2nd projector,and so ontillall fixturesare connected.Ifthevoltage supplied

is 200V-240V, the maximum projectors connected is 8pcs, if it is 100V-120V, the maximum is 4pcs. The diameter of the cores

ofthewiresfor thePowerin/outcablesmustbeequalorbiggerthan2.5mm2.

●Theearth wire(yellow/green) must be connectedto theground.And electricalconnectionmust bein

accordancewiththestandardsconcerned.

●Ifanyquestionsaboutthe electricalinstallation,donotcontinue butconsulta qualifiedelectrician.

●DMXCONTROLCONNECTION:

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with

each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon5 pin (which are included with the

projector)or5pinXLRplugsand sockets.The XLR'sareconnectedasshowninthefigureabove.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets

mustn’t be connected in any way other than mentioned in the above figure. The unit accepts digital control signals in protocol

DMX512(1990).

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second

fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX

terminatorasshowninthefigurebelow.

●DMXTERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electricalnoisefromdisturbingandcorruptingtheDMXcontrolsignals.

The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected across pins 2 and 3, which is then plugged

intotheoutputsocketonthe lastprojectorinthe chain.The connectionsare illustratedbelow.

6. SETUPANDCONFIGURATION

●FRONTPANELOPERATION

To browse through or modify the projector’s functions, press key ENTER for more than 3 seconds to unlock the control panel and

enter the menus. To set or browse through the projector’s functions, press key UP or DOWN. Press the key ENTER to enter the

submenusandthe currentparameterswillbedisplayedwhile flashing.Press key UP or DOWN tochange values(plusorminus)

Presskey ENTER to save your changesand enter into the upperlevelmenuwhile flashings stop;

Presskey FUNC,itwillreturnto theupper menu(parametersnotsaved)orbrowse through1st levelmenus;

Presskey FUNC for1 secondornonekeyispushed for1minute, the menu will be escapedand currentoperationmodedisplayed.

IfDMXsignalisavailable, LEDindication ison.Otherwiseitisoff.

●DMXSTARTADDRESS

EachProjectormustbegivena DMXstartaddressso that the correctprojectorrespondstothe correctcontrolsignals. ThisDMXstart

DMX

Controller

Teminator

DMX OUT DMX IN DMX OUT DMX IN

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain. PIN 3

PIN 2

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

controller.The Unit has1 DMXmode.It has7channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 008,No.3

projector’s address 015, No. 4 projector’s address022,andsoon.

Launch theprojector. Pressbutton ENTER morethan2secondsto unlockpanel.

Pressbutton ENTER todisplayDMXaddress;

Pressbutton UP and DOWN,youcanset theaddress;

Pressbutton ENTER to confirm;afterpoweredonnext time,the default willbelastvalue saved

Pressbutton FUNC, itwillreturntotheuppermenu

●STAND-ALONEMODE

Operate the projector without connecting with a controller, enable the master mode through the operation panel, the

projector will run in Stand-Alone mode automatically.

DMX address can be set at any number within 512.

●MASTER/SLAVEMODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,

connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR control cable and then connect the second

fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the

last fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.

StartAddressesofall Slaves are 001; Operation mode of the Master can be set any mode for a Master’ and Slaves’ operation mode can

be setaccordingly

AfterPowered on,the group willruninMaster/Slave Mode

7. OPERATIONMENU

1stlevel menu

2ndlevelmenu

3rdlevelmenu

4thlevelmenu

Address

001 -512

DMXAddress

ConfigSetup

MasterSlave

Slave

DefaultSlave

Master

LanguageSetup

English

Default：English

Chinese

LcdLightSetup

Backlightwillbeoff

3minutesafternone

button ispushed

Off

Slave

Master Slave

Teminator

DMX OUT DMX IN DMX OUT DMX IN

Display Invert

Yes

FactorySetting

Yes

PRMTransmit

Yes

cleanProgra

Yes

Moto offset

Color

Focus

-128-127

Moto Reset

Yes/No

Information

LEDTemperature

FixtureuseTime

XXXX

SoftwareVersion

X.X.X

TestMode

Auto Test

Dimmer

000 -255

LEDbrightness

Color

000 -255

Motorposition

Effect

000 -255

Motorposition

Focus

000 -255

Motorposition

OperationMode

DMX Mode

Yes

User Memory

Yes

PresetMemory

(PR01~PR16)

PR01~PR16

User PrograEdit

（ET01~ET16）

Dimmer

000 -255

Strobe

000 -255

Color

000 -255

Effect

000 -255

Focus

000 -255

KeepTime

000 –200(0-20S)

8. DMXPROTOCOL

Channel No.

Function

DMXValue

Description

Dimmer

000-255

Dimmer Fine

000-255

Dimmer in16bit

Strobe

000-007

008-255

Strobespeedfromslowtofast

Colorwheel

000-009

White

010-019

White -Magenta

020-029

Magenta

9. TECHNICALDATA

ELECTRICSPECIFICATIONS

Inputvoltage:100V~240VAC，50/60Hz

Inputpower:160W@ 230V

Maximumcurrent:AC0.9A

Powerfactor：PF>90%

LIGHTSOURCESPECIFICATIONS

Qty 1pc,TX-3636W150FC120-NUVENG-A01

030-039

Magenta–Orange

040-049

Orange

050-059

Orange-Yellow

060-069

Yellow

070-079

Yellow-Blue

080-089

Blue

090-099

Blue–Cyan

100-109

Cyan

110-119

Cyan -White

120-127

White

128-191

Clockwiserotationfromslowtofast

192-255

Anti-clockwiserotationfromslowtofast

EffectWheel

000-001

002-127

Clockwiserotationfromslowtofast

128-255

Anti-clockwiserotationfromslowtofast

Focus

000-255

Motorposition

Function

000-199

200-209

Motorreset

210-255

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting Beleuchtungsausrüstung Handbücher

PR Lighting

PR Lighting XPAR 354 Bedienungsanleitung

PR Lighting

PR Lighting CHAMELEON PR-2012H Bedienungsanleitung

PR Lighting

PR Lighting PR-8920 Bedienungsanleitung

PR Lighting

PR Lighting XPar 360 Bedienungsanleitung

PR Lighting

PR Lighting PR-2203 XR 200 Bedienungsanleitung

PR Lighting

PR Lighting XL 1500 Bedienungsanleitung

PR Lighting

PR Lighting AQUA 380 BWS Bedienungsanleitung

PR Lighting

PR Lighting PR-2330 Bedienungsanleitung

PR Lighting

PR Lighting XR130 Beam Bedienungsanleitung

PR Lighting

PR Lighting CUBIX300 Bedienungsanleitung

PR Lighting

PR Lighting XLED 4007 BEAM Bedienungsanleitung

PR Lighting

PR Lighting PR-8120 Bedienungsanleitung

PR Lighting

PR Lighting XR 230 Beam Bedienungsanleitung

PR Lighting

PR Lighting AQUA 350 BEAM Bedienungsanleitung

PR Lighting

PR Lighting PR-8121 Bedienungsanleitung

PR Lighting

PR Lighting Mega Colour 2500 Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 3000-W FRAMING Bedienungsanleitung

PR Lighting

PR Lighting XLED 590 Bedienungsanleitung

PR Lighting

PR Lighting XR250 Bedienungsanleitung

PR Lighting

PR Lighting PR-6000 FRAMING Bedienungsanleitung

PR Lighting

PR Lighting AQUA 380 BEAM Bedienungsanleitung

PR Lighting

PR Lighting PR-8835 Bedienungsanleitung

PR Lighting

PR Lighting DESIGN 150 Bedienungsanleitung

PR Lighting

PR Lighting TANGO FRAMING Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung