PR Lighting XLED 590 Bedienungsanleitung

XLED 590

PR-8100

This product manual contains important information about the safe installation and use of this

projector. Please read and follow these instructions carefully and keep this manual in a safe place

for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/18

INDEX

SAFE USAGE OF THE PROJECTOR 3

INSTALLING THE PROJECTOR 4

POWER SUPPLY – MAINS 4

CONTROL CONNECTIONS 4

DMX TERMINATOR 5

SETUP OPTIONS-PROJECTOR CONFIGURATION 6

TO SET THE DMX START ADDRESS 6

OPERATION MENU 7

DMX PROTOCOL 12

LED INDICATION 13

MAINTENANCE 13

KEEPING THE PROJECTOR CLEAN 13

TROUBLESHOOTING 13

TECHNICAL DATA 14

ELECTRICAL DIAGRAM 16

COMPONENT ORDER CODES 17

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without

notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of

product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence

arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good

condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the

unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.

ACCESSORIES

These items are packed together with the projector:

Name Quantity Unit Remark

G clamps 2 Pcs

Ωclamps 2 Pcs Options

XLR cable 1 Pc 5-pin plug

Safety cord 1 Pc

This manual 1 Pc

3/18

SAFE USAGE OF THE PROJECTOR

When unpacking and before disposing of the carton, check there is no transportation damage before using the projector.

Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.

The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture,

excessive heat, humidity and dust. Do not allow contact with water or any other liquids.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces. Be sure

that no ventilation slots are blocked.

Do not project the beam onto inflammable surfaces, minimum distance is 5m. 5m

Avoid direct exposure to the light from the lamp. The light is harmful to the eye.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact

with other cables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.

Keep the optical system clean. Do not touch the LED lens with bare hands.

The projector should always be installed with a secondary safety fixing. On the projector base brink,there is a hole for the

safety cord provided. It should be attached as shown in “installing the projector” section.

LED lens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired, for

example by cracks or deep scratches.

Exterior surface temperatures of the luminaire after 5 minutes operation is 40℃, when steady state is achieved 50℃.

There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the

covers removed.

Always disconnect from the mains, when the device is not in use or before cleaning it or

before attempting any maintenance work !

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

4/18

INSTALL THE PROJECTOR

CLAMP

SAFETY CORD

HOLE FOR SAFETY CORD

To pass the SAFETY CORD

through this HOLE for safety !

WARNING

Take 2 clamps and the safety cord out from the package and mount 2 clamps on the underside of fixture with 4 retainers

attached to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the

WARNING on the bottom side of the fixture base as shown above) To pass the SAFETY CORD through this HOLE

for safety! Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning. Always

ensure that the structure that you are going to mount the projector on is secure and is strong enough to support a weight

of XLED 590.

WARNING:

1. The projector MUST NOT be lifted or carried by the clamps.

2. For safety reasons, the safety cord should afford 10 times of the unit’s weight.

POWER SUPPLY-MAINS

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked

on the panel of the projector. It is recommended that each projector be supplied separately so that they may be

individually switched on and off.

IMPORTANT

It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant

standards.

CONTROL CONNECTION

Connection between the controller and a projector and between one projector and another must be made with a 2

core-screened cable, with each core having at least a 0.5mm diameter. Connection to and from the projector is via

5/18

cannon 5 pin (which are included with the projector) XLR plugs and sockets. The XLR's are connected as shown in the

figure above.

Note: Care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of

the plug is not connected in any way. The XLED 590 accepts digital control signals in protocol DMX512 (1990).

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input

and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown

in the figure below.

DMX IN DMX OUT DMX IN DMX OUT DMX IN

DMX IN FROM

CONTROLLER TERMINATER

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This

prevents electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2 and 3, which is

then plugged into the output socket on the last projector in the chain. The connections are illustrated below.

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert it into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

120

6/18

SETUP OPTIONS-PROJECTOR CONFIGURATION

Projector configuration can be set conveniently via push-button switch and LCD display. Turn the projector on and the

LCD display will show the DMX address you set and saved last time and it can be reset and saved again as you please.

Launch the projector and press button ENTER for more than 5 seconds to unlock the panel, the LCD will show the

function menu of the projector, each main menu has its submenus and each submenu has a specific function. For

details, please see the “OPERATION MENU” section.

Press button UP or DOWN if you want to browse through the various Setup Options. Press button ENTER to save your

settings or enter the next menu. Press button UP or DOWN to shift.

Press button FUNC, it will return to the upper menu one by one. If you stay for minutes, it will show display status

automatically.

TO SET THE DMX START ADDRESS

Each XLED 590 must be given a DMX start address so that the correct projector responds to the correct control signals.

This DMX start address is the channel number from which the projector starts to “listen” to the digital control information

being sent out from the controller. The XLED 590 has 3 DMX modes, which are standard mode, extended mode and

short mode. For example, the standard mode has 13 channels, so set the No. 1 projector’s address 001, No. 2

projector’s address 014, No. 3 projector’s address 027, No. 4 projector’s address 040, and so on.

Launch the projector. Press button ENTER for more than 5 seconds to unlock the panel.

Press button ENTER to display DMX Address;

Press button UP and DOWN to set the address;

Press button ENTER to confirm. At the same time, the GREEN LED will flash one time. It means the setting has

been enabled.

Press button FUNC, it will return to the upper menu one by one.

7/18

OPERATION MENU

1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL 5th LEVEL 6th LEVEL

PR LIGHTING

DMX Address

PR LIGHTING

DMX Address

XXX

PR LIGHTING

Reset

PR LIGHTING

Reset

Are You Sure

PR LIGHTING

DMX Mode

Standard 16

PR LIGHTING

DMX Mode

Extended 16

PR LIGHTING

DMX Mode

PR LIGHTING

DMX Mode

Short 8

PR LIGHTING

When DMX is Lost

Normal Time Out

PR LIGHTING

Config Settings

PR LIGHTING

Loss of DMX PR LIGHTING

When DMX is Lost

Hold Last Value

PR LIGHTING

Pan DMX Invert

OFF

PR LIGHTING

Pan DMX Invert PR LIGHTING

Pan DMX Invert

PR LIGHTING

Tilt DMX Invert

OFF

PR LIGHTING

Tilt DMX Invert PR LIGHTING

Tilt DMX Invert

PR LIGHTING

Pan Tilt Swap

OFF

PR LIGHTING

Pan Tilt Swap PR LIGHTING

Pan Tilt Swap

PR LIGHTING

Dimmer Invert

OFF

PR LIGHTING

Dimmer Invert PR LIGHTING

Dimmer Invert

PR LIGHTING

Defaults

Off

PR LIGHTING

Option Settings

PR LIGHTING

Defaults PR LIGHTING

Defaults

Restore Defaults

PR LIGHTING

Display

On Always

PR LIGHTING

Display Mode PR LIGHTING

Display

Off After Delay

8/18

PR LIGHTING

Display Invert

Off

PR LIGHTING

Display Invert PR LIGHTING

Display Invert

PR LIGHTING

Display Dimming

PR LIGHTING

Disp Dim Level

PR LIGHTING

Display Options

PR LIGHTING

Display Contrast

PR LIGHTING

Display Contrast

PR LIGHTING

LED Hours

PR LIGHTING

LED Hours =

******

PR LIGHTING

Power On Hours

PR LIGHTING

Power On Hours =

******

PR LIGHTING

Driver Board

PR LIGHTING

Driver Board =

XX℃

PR LIGHTING

Temperature PR LIGHTING

Head Sensor

PR LIGHTING

Head Sensor =

XX℃

PR LIGHTING

Software Version

PR LIGHTING

Display Board

PR LIGHTING

Display Board =

*.*.*

PR LIGHTING

View DMX Values

PR LIGHTING

DMX Channel

XXX= XXX

PR LIGHTING

Information

PR LIGHTING

Electronic SN

PR LIGHTING

Electronic SN =

************

PR LIGHTING

Factory Setup

OFF

PR LIGHTING

Calibration Menu

Red

PR LIGHTING

Calibration Menu

Red

PR LIGHTING

Calibration Menu

Green

PR LIGHTING

Calibration Menu

Green

PR LIGHTING

Factory Setup

PR LIGHTING

Factory Setup

(Or press buttons

UP 、DOWN and

ENTER to enter

Calibration Menu) Calibration Menu

Blue

PR LIGHTING

Calibration Menu

Blue

PR LIGHTING

Self Test

OFF

PR LIGHTING

Test Modes

PR LIGHTING

Self Test PR LIGHTING

Self Test

9/18

PR LIGHTING

Operation Mode =

DMX Operation

PR LIGHTING

Select Memory

User Memory 1

PR LIGHTING

Select Memory

User Memory 2

PR LIGHTING

Select Memory

Preset Memory 1

PR LIGHTING

Select Memory

Preset Memory 2

PR LIGHTING

Operation Mode =

Master Mode

PR LIGHTING

Select Memory

Preset Memory 3

PR LIGHTING

Select Memory

User Memory 1

PR LIGHTING

Select Memory

User Memory 2

PR LIGHTING

Select Memory

Preset Memory 1

PR LIGHTING

Select Memory

Preset Memory 2

PR LIGHTING

Operation Mode =

Slave Mode

PR LIGHTING

Select Memory

Preset Memory 3

PR LIGHTING

Operation Mode

PR LIGHTING

Operation Mode =

Static Scene

PR LIGHTING

Dimmer

PR LIGHTING

Dimmer

XXX

PR LIGHTING

Color Temp.

PR LIGHTING

Color Temp.

XXX

PR LIGHTING

RGB Macros

PR LIGHTING

RGB Macros

XXX

PR LIGHTING

Red

PR LIGHTING

Red

XXX

PR LIGHTING

Green

PR LIGHTING

Green

XXX

PR LIGHTING

Blue

PR LIGHTING

Blue

XXX

PR LIGHTING

Strobe

PR LIGHTING

Strobe

XXX

10/18

PR LIGHTING

Pan Coarse

PR LIGHTING

Pan Coarse

XXX

PR LIGHTING

Pan Fine

PR LIGHTING

Pan Fine

XXX

PR LIGHTING

Tilt Coarse

PR LIGHTING

Tilt Coarse

XXX

PR LIGHTING

Tilt Fine

PR LIGHTING

Tilt Fine

XXX

PR LIGHTING

M-Speed

PR LIGHTING

M-Speed

XXX

PR LIGHTING

Delay

PR LIGHTING

Delay

X.XX Seconds

PR LIGHTING

User Memory

PR LIGHTING

Scene

PR LIGHTING

Link To Step

PR LIGHTING

Link To Step

PR LIGHTING

Dimmer

PR LIGHTING

Dimmer

XXX

PR LIGHTING

Color Temp.

PR LIGHTING

Color Temp.

XXX

PR LIGHTING

RGB Macros

PR LIGHTING

RGB Macros

XXX

PR LIGHTING

Red

PR LIGHTING

Red

XXX

PR LIGHTING

Green

PR LIGHTING

Green

XXX

PR LIGHTING

Blue

PR LIGHTING

Blue

XXX

PR LIGHTING

Strobe

PR LIGHTING

Strobe

XXX

PR LIGHTING

Pan Coarse

PR LIGHTING

Pan Coarse

XXX

PR LIGHTING

Pan Fine

PR LIGHTING

Pan Fine

XXX

PR LIGHTING

Tilt Coarse

PR LIGHTING

Tilt Coarse

XXX

PR LIGHTING

Tilt Fine

PR LIGHTING

Tilt Fine

XXX

PR LIGHTING

User Memories

PR LIGHTING

Edit User Memory

PR LIGHTING

User Memory

PR LIGHTING

Scene

PR LIGHTING

M-Speed

PR LIGHTING

M-Speed

XXX

Andere Handbücher für XLED 590

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting Beleuchtungsausrüstung Handbücher

PR Lighting

PR Lighting AQUA LED 3000-W FRAMING Bedienungsanleitung

PR Lighting

PR Lighting XL WASH 700 Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

PR Lighting

PR Lighting XR250 Bedienungsanleitung

PR Lighting

PR Lighting TANGO SPOT Bedienungsanleitung

PR Lighting

PR Lighting AQUA 380 BEAM Bedienungsanleitung

PR Lighting

PR Lighting XR 230 Beam Bedienungsanleitung

PR Lighting

PR Lighting XPAR 354 Bedienungsanleitung

PR Lighting

PR Lighting XPar 150 Zoom Bedienungsanleitung

PR Lighting

PR Lighting CHAMELEON PR-2012H Bedienungsanleitung

PR Lighting

PR Lighting DESIGN 150 Bedienungsanleitung

PR Lighting

PR Lighting CENTURY SPOT PR-2002 Bedienungsanleitung

PR Lighting

PR Lighting XR130 Beam Bedienungsanleitung

PR Lighting

PR Lighting ARC LED 372 Bedienungsanleitung

PR Lighting

PR Lighting PR-2001L Bedienungsanleitung

PR Lighting

PR Lighting PR-2330 Bedienungsanleitung

PR Lighting

PR Lighting XR 380 BWS Bedienungsanleitung

PR Lighting

PR Lighting PR-8170A Bedienungsanleitung

PR Lighting

PR Lighting PR-111ER MOON Bedienungsanleitung

PR Lighting

PR Lighting XR 200 BEAM Leitfaden

PR Lighting

PR Lighting LS150 TREE Bedienungsanleitung

PR Lighting

PR Lighting XR 1400 Framing Bedienungsanleitung

PR Lighting

PR Lighting TANGO FRAMING Bedienungsanleitung

PR Lighting

PR Lighting AQUA 380 BWS Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung