PR Lighting XL WASH 700 Bedienungsanleitung

XL WASH 700

PR-2705

This product manual contains important information about the safe installation and use of this

projector. Please read and follow these instructions carefully and keep this manual in a safe place

for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/20

INDEX

SAFE USAGE OF THE PROJECTOR 3

INSTALLING THE PROJECTOR 4

FITTING THE LAMP 4

POWER SUPPLY – MAINS 5

CONTROL CONNECTIONS 5

DMX TERMINATOR 6

SETUP OPTIONS-PROJECTOR CONFIGURATION 6

TO SET THE DMX START ADDRESS 6

OPERATION MENU 7

ERROR MESSAGES 9

DMX PROTOCOL 10

LED INDICATION 13

MAINTENANCE 13

LUBRICATION 13

KEEPING THE PROJECTOR CLEAN 13

TROUBLESHOOTING 14

TECHNICAL DATA 15

ELECTRICAL DIAGRAM 18

COMPONENT ORDER CODES 19

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without

notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of

product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence

arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good

condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the

unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.

ACCESSORIES

These items are packed together with the projector:

Name Quantity Unit Remark

G clamps 2 Pcs

XLR cable 1 Pc 3-pin plug

This manual 1 Pc

Ωclamps 2 Pcs Options

3/20

SAFE USAGE OF THE PROJECTOR

When unpacking and before disposing of the carton check there is no transportation damage before using the projector.

Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.

The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture,

excessive heat, humidity and dust. Do not allow contact with water or any other liquids.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces. Be sure

that no ventilation slots are blocked.

Do not project the beam onto inflammable surfaces, minimum distance is 5m. 5m

Avoid direct exposure to the light from the lamp. The light is harmful to the eye.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact

with other cables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.

Keep the lamp clean. Do not touch the lamp glass with bare hand.

The projector should always be installed with a secondary safety fixing. A safety cord is supplied for this; it should be

attached as shown in “installing the projector” section.

The lamp used in this projector is a discharge lamp. After switching off don’t attempt to restart the projector until lamp has

cooled, this will require approx 15 minutes. Switching the lamp on and off at short intervals will reduce the life of both the

lamp and the projector. But occasional breaks will prolong the life of the lamp and projector.

Never run the projector without a lamp.

There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the

covers removed.

Always disconnect from the mains, when the device is not in use or before cleaning it or

before attempting any maintenance work !

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

4/20

INSTALL THE PROJECTOR

(2PCS)

HANDLES

(2PCS)

SAFETY CORD

CLAMPS

To pass 2 SAFETY CORDS

through the TRUSS for safety!

WARNING

TRUSS

106

339

Take 2 clamps and 2 safety cords out from the package and mount 2 clamps on the underside of fixture with 2 retainers

attached to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the

WARNING on the underside of the base as shown above) To pass 2 SAFETY CORDS through the TRUSS for

safety! Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning. Always

ensure that the structure that you are going to mount the projector is secure and is strong enough to support a weight of

XL 700.

WARNING:

1. Unlock the PAN and TILT before the 1st application of projector for safety.

2. The projector MUST be lifted or carried by the HANDLES instead of clamps.

3. For safety the safety cord should afford 10 times of the unit’s weight.

FITTING THE LAMP

NUT

LAMP REFLECTER

Lock the yoke before fitting/replacing the lamp.

Loosen 4 screws and open the back covers, you can see the structure as shown in the figure above.

Loosen 2 nuts at the both ends of lamp and take out the worn-out lamp. Suggest to free one end after another.

Fit new lamp and fasten 2 screws at the both ends of lamp. Note: don’t touch the bulb of the new lamp with bare hand so

as not to influence the beam output; the PST (pumping stem tip off) on the bulb facing the rear cover with fans

perpendicularly and being not in the beam’s way is a must and aids cooling.

Close the rear cover and fasten 4 screws.

NOTE: The convex of the nuts should face to the side when fitting the lamp.

WARNING: The MSR series are high-pressure lamps with external igniters ( ). Care should always be taken

when handling these lamps. Always read the manufacturers "Instructions for use" enclosed with the lamp.

5/20

POWER SUPPLY-MAINS

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked

on the panel of the projector. It is recommended that each projector be supplied separately so that they may be

individually switched on and off.

IMPORTANT

It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant

standards.

CONTROL CONNECTION

Connection between controller and projector and between one projector and another must be made with a 2

core-screened cable, with each core having at least a 0.5mm diameter. Connection to and from the projector is via

cannon 3 pin (which are included with the projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown

in the figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of

the plug is not connected in any way. The XL WASH 700 accepts digital control signals in protocol DMX512 (1990).

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input

and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown

in the figure below.

DMX IN CONTROLLER TERMINATER

DMX OUT

DMX IN DMX IN DMX OUT DMX IN DMX OUT

No.1 No.2 No. n

6/20

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This

prevents electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2 and 3, which is

then plugged into the output socket on the last projector in the chain. The connections are illustrated below.

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

SETUP OPTIONS-PROJECTOR CONFIGURATION

CODER BUTTON

Projector configuration can be set conveniently via pressbutton switch and LCD display. Turn the projector on and the

LCD display will show DMX address you set and save last time and it can be reset and saved again as you please.

Launch the projector. Press button ENTER more than 5 seconds to unlock panel.

Press button UP or DOWN if you want to browse through the various Setup Options. There are 8 option codes

from DMX Address to Lamp Manual Control, and each code has a specific function. If you turn the coder

knob clockwise, the function like as button UP . On the contrary, the function like as button DOWN .

Press button ENTER to save your settings or enter the next menu. There is same function if you push the coder knob.

Press button UP or DOWN to shift.

Press button FUNC, it will return to the upper menu one by one. If you stay for minutes defaulted will show display status

automatically.

TO SET THE DMX START ADDRESS

Each XL WASH 700 must be given a DMX start address so that the correct projector responds to the correct control

signals. This DMX start address is the channel number from which the projector starts to “listen” to the digital control

information being sent out from the controller. The XL WASH 700 has 3 DMX modes. There are standard mode,

extended mode and short mode. For example standard mode has 17 channels, so set the No. 1 projector’s address 001,

No. 2 projector’s address 018, No. 3 projector’s address 035, No. 4 projector’s address 052, and so on.

Launch the projector. Press button ENTER or coder knob more than 5 seconds to unlock panel.

Press button FUNC to display DMX address;

Press button UP and DOWN, you can set the address;

Press button ENTER to confirm; In the same time. The GREEN LED will flash one time. It means the setting has

been enabled.

Press button FUNC, it will return to the upper menu one by one.

7/20

OPERATION MENU

1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL

PR LIGHTING

XL SERIES

XL 1200 WASH

DMX Address=001

DMX Address DMX Address

(001-512)

Reset Reset

Are You Sure?

DMX Mode

Standard 16

DMX Mode

Extended 16

DMX Mode

Short 8

Lamp Control By

Control Channel

Lamp Control By

Power On

Lamp Control

Lamp Control By

DMX Present

Fixture type=

XL 1200

Fixture type=

XL 700

Fixture type=

XL 575

Fixture type=

XL 1200 FS

Fixture type=

XL 1200 Wash

Fixture type=

XL 700 Wash

Config Settings

Factory Settings

(Press button

DOWN/UP/ENTER at the same

time to enter the sub-menu)

Fixture type

(WARNING：Never change

the fixture type or the

system will be damaged!)

Fixture type=

XL 1800

Colour Positions

STEPPED

Colour Positions Colour Positions

LINEAR

Pan DMX Invert

OFF

Pan DMX Invert Pan DMX Invert

Tilt DMX Invert

OFF

Tilt DMX Invert Tilt DMX Invert

Pan Tilt Swap

OFF

Pan Tilt Swap Pan Tilt Swap

Dimmer Invert

OFF

Dimmer Invert Dimmer Invert

Zoom Invert

OFF

Zoom Invert Zoom Invert

CMY Invert

OFF

CMY Invert CMY Invert

CTO Invert

OFF

Option Settings

CTO Invert CTO Invert

8/20

Defaults

OFF

Defaults Defaults

Restore Defaults

Display

On Always

Display Mode Display

Off After Delay

Disp Dim Level

Min

Disp Dim Level

Display Dimming

Disp Dim Level

Full

Display Contrast Display Contrast

XXX(1~36, Default is 16)

Language =

English

Display Options

Display Language Language =

Chinese

Lamp Hours Lamp Hours =

Reset Lamp Hours

Are You Sure?

Total Hours Total Hours =

Display Board Display Board =

XX℃

Driver Board 1 Driver Board 1 =

XX ℃

Driver Board 2 Driver Board 2 =

XX ℃

Pan and Tilt Pan and Tilt =

XX ℃

Temperature

Head Sensor Head Sensor=

XX ℃

Display Board Display Board =

X.X.X

Driver Board 1 Driver Board 1 =

X.X.X

Driver Board 2 Driver Board 2 =

X.X.X

Pan and Tilt Pan and Tilt =

X.X.X

Software Version

Power Board Power Board =

X.X.X

Information

View DMX values DMX Channel

1=0

Factory Setup

OFF

Factory Setup Factory Setup

Self Test

OFF

Test Modes

Self Test self test

Lamp Status Status = XXX

Control = X

Turn Lamp On

Lamp Manual

Control

Turn Lamp Off

9/20

ERROR MESSAGES

In the course of launch, XL WASH 700 examines automatically whether there are errors and if there are, it will display

information as follows:

Display Message

Sensor Err S1-M1 Colour wheel 1 (1# drive board motor 1) error

Sensor Err S1-M2 CTO (1# drive board motor 2) error

Sensor Err S1-M3 CYM-cyan (1# drive board motor 3) error

Sensor Err S1-M4 CYM-yellow (1# drive board motor 4) error

Sensor Err S1-M5 CYM-magenta (1# drive board motor 5) error

Sensor Err S1-M6 Dimmer (1# drive board motor 6) error

Sensor Err S2-M1 Zoom (2# drive board motor 1) error

Sensor Err S2-M2 Inside lens 1 (2# drive board motor 2) error

Sensor Err S2-M3 Inside lens 2 (2# drive board motor 3) error

Sensor Err S2-M4 Colour wheel 2 (2# drive board motor 4) error

Sensor Err S2-M5 Strobe 1 (2# drive board motor 5) error

Sensor Err S2-M6 Strobe 2 (2# drive board motor 6) error

10/20

DMX PROTOCOL

Short

mode

Standard

mode

Extended

mode FUNCTION DMX DESCRIPTION

000-010 Black

011-025 Open

026-225 Strobe speed from slow to fast

1 1 1 Strobe

226-255 Open

000-007 Black

2 2 2 Dimmer

008-255 Dimming from dark to light (0-100%)

3 Dimmer Fine 000-255 Dimmer in 16 Bit precision

000-016 White

017-035 Yellow+ Magenta=Red

036-054 Yellow

055-073 Yellow+ Cyan=Green

074-092 Cyan

093-110 Cyan+ Magenta=Blue

111-128 Magenta

3 3 4 CYM Macro

129-255 CYM colour mixing from slow to fast

4 4 5 CYM-Cyan 000-255 Cyan (Linear 0-100%)

CYM-Cyan

Fine 000-255 Cyan in 16 Bit precision

5 5 7 CYM-Yellow 000-255 Yellow (Linear 0-100%)

CYM-Yellow

Fine 000-255 Yellow in 16 Bit precision

6 6 9 CYM-Magenta 000-255 Magenta (Linear 0-100%)

CYM-Magenta

Fine 000-255 Magenta in 16 Bit precision

7 7 11 CTO 000-255 Linear adjust from high to low

12 CTO Fine 000-255 CTO in 16 Bit precision

000-016 White

017-024 White/colour 1

025-032 Colour 1

033-040 Colour 1/colour 2

041-048 Colour 2

049-056 Colour 2/colour 3

057-064 Colour 3

065-072 Colour 3/colour 4

073-080 Colour 4

081-088 Colour 4/colour 5

089-096 Colour 5

097-104 Colour 5/colour 6

105-112 Colour 6

113-120 Colour 6/colour 7

121-127 white

128-133 Rainbow rotation speed 1 (slowest)

8 8 13 Colour Wheel 1

134-139 Rainbow rotation speed 2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting Beleuchtungsausrüstung Handbücher

PR Lighting

PR Lighting PR-8835 Bedienungsanleitung

PR Lighting

PR Lighting AQUA 380 BEAM Bedienungsanleitung

PR Lighting

PR Lighting PR-2330 Bedienungsanleitung

PR Lighting

PR Lighting PR-8836 Bedienungsanleitung

PR Lighting

PR Lighting XLED 590 Bedienungsanleitung

PR Lighting

PR Lighting XR130 Beam Bedienungsanleitung

PR Lighting

PR Lighting PR-111ER MOON Bedienungsanleitung

PR Lighting

PR Lighting XPar 360 Bedienungsanleitung

PR Lighting

PR Lighting LS150 TREE Bedienungsanleitung

PR Lighting

PR Lighting CHAMELEON PR-2012H Bedienungsanleitung

PR Lighting

PR Lighting TANGO FRAMING Bedienungsanleitung

PR Lighting

PR Lighting AQUA 580 BWS Bedienungsanleitung

PR Lighting

PR Lighting XL 1500 Bedienungsanleitung

PR Lighting

PR Lighting XLED 4007 BEAM Bedienungsanleitung

PR Lighting

PR Lighting TANGO SPOT Bedienungsanleitung

PR Lighting

PR Lighting XR 200 BEAM Leitfaden

PR Lighting

PR Lighting PR-8920 Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

PR Lighting

PR Lighting PR-2900 Bedienungsanleitung

PR Lighting

PR Lighting PR-8170A Bedienungsanleitung

PR Lighting

PR Lighting Mega Colour 2500 Bedienungsanleitung

PR Lighting

PR Lighting PR5000 Bedienungsanleitung

PR Lighting

PR Lighting DESIGN 150 Bedienungsanleitung

PR Lighting

PR Lighting XR250 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung