PR Lighting PR-2203 XR 200 Bedienungsanleitung

XR 200（BEAM）

PR-2203

This product manual contains important information about the safe installation and use of this

projector. Please read and follow these instructions carefully and keep this manual in a safe place

for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/20

INDEX

SAFE USAGE OF THE PROJECTOR 3

INSTALLING THE PROJECTOR 4

FITTING LAMP 4

POWER SUPPLY – MAINS 5

CONTROL CONNECTIONS 5

DMX TERMINATOR 6

SETUP OPTIONS-PROJECTOR CONFIGURATION 6

TO SET THE DMX START ADDRESS 6

STAND-ALONE MODE 7

MASTER/SLAVEMODE 7

OPERATION MENU 8

REPLACING GOBOS 10

DMX PROTOCOL 11

INDICATION OF LED DIGITAL TUBE 13

MAINTENANCE 13

LUBRICATION 13

KEEPING THE PROJECTOR CLEAN 13

TROUBLESHOOTING 14

TECHNICAL DATA 15

ELECTRICAL DIAGRAM 18

COMPONENT ORDER CODES 19

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without

notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of

product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence

arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good

condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the

unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.

ACCESSORIES

These items are packed together with the projector:

Name Quantity Unit Remark

G clamps 2 Pcs

XLR cable 1 Pc with plug

Safety cord 2 Pcs

This manual 1 Pc

Ωclamps 2 Pcs Optional

When unp

Should the

The projec

excessive

The projec

that no ven

Do not proj

void direc

Do not atte

Electrical c

Before inst

It is essenti

Do not con

Make sure

with other c

Keep the l

The projec

attached a

The lamp

cooled, thi

lamp and t

Never run t

The lamp s

Shields an

impaired, f

Exterior su

There is n

covers rem

If you have

Always

before a

cking and be

e be any da

or is for ind

eat, humidity

or is not desi

or is only inte

or must be in

ilation slots a

ct the beam

exposure to

pt to disma

nnection mu

llation, ensu

l that each p

ect this devi

that the pow

bles. Only ha

mp clean. D

or should al

shown in “in

sed in this pr

will require a

e projector.

he projector

hall be chang

lens shall b

r example b

face tempera

user service

oved.

any question

isconnec

tempting

SAF

ore disposin

age caused

or use only,

and dust. Do

ned or inten

ded for insta

talled in a lo

e blocked.

onto inflamm

he light from

tle and/or m

t only be car

that the volt

ojector is cor

e to any othe

r-cord is nev

dle the powe

not touch th

ays be insta

talling the pr

jector is a di

pprox 15 min

ut occasional

ithout a lamp

ed if it has be

changed if

cracks or de

tures of the lu

ble parts insi

, don’t hesita

from the

ny maint

USAG

of the carto

y transportat

P20. Use o

not allow co

ed to be mou

lation, operat

ation with ad

ble surfaces,

the lamp. Th

dify the proje

ied out by qu

ge and freq

ectly earthed

r types of dim

r crimped or

-cord by the

lamp glass

led with a se

jector” sectio

charge lamp.

tes. Switchi

breaks will p

ome damag

they have b

p scratches.

minaire after

e the projec

te to consult

mains, w

nance wo

3/20

OF TH

check if ther

ion, consult y

ly in dry loc

tact with wat

nted directly

on and maint

quate ventila

minimum di

light is harm

tor in any wa

lified person

ency of pow

and that elec

mer apparatu

damaged by

lug. Never p

ith bare han

ondary safe

After switchi

g the lamp o

olong the life

d or thermall

come visibly

minutes op

or, do not op

our dealer or

en the d

rk !

PROJ

is no transp

ur dealer an

tions. Keep t

r or any othe

n to inflamm

nance by qu

ion, at least

tance is 12m.

ul to the eye.

el.

r supply mat

rical installati

sharp edges

ll out the plu

y fixing. A sa

g off don’t att

and off at s

f the lamp a

deformed o

damaged to

ration is 35℃

n the housin

manufacture

vice is no

CTO

rtation dama

do not use t

is device a

liquids.

ble surfaces.

alified person

0cm from adj

12m

h the power r

n conforms t

. Never let th

by tugging t

fety cord is s

mpt to resta

ort intervals

d projector.

reached its li

uch an exte

, when stead

and never

in use o

e before usi

e apparatus.

ay from rain

el.

acent wall su

quirements

all relevant

power-cord c

e power-cor

pplied for th

t the projecto

ill reduce the

fe limi

t than their

state is achi

perate the pr

before cl

g the project

and moistur

faces. Be su

f the project

tandards.

me into conta

s; it should b

until lamp h

life of both th

ffectiveness

ved 45℃,

jector with th

aning it

4/20

INSTALL THE PROJECTOR

Take 2 clamps and 1 safety cords out from the package and mount 2 clamps on the underside of fixture with 4 retainers

attached to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the

WARNING on the underside of the base as shown above) Always ensure that the projector is firmly anchored to avoid

vibration and slipping whilst functioning. Always ensure that the structure that you are going to mount the projector is

secure and is strong enough to support the weight of the fixture.

WARNING

1. The projector MUST be lifted or carried by the HANDLES instead of clamps.

2. For safety the safety cord should support 10 times of the unit’s weight.

FITTING THE LAMP

Unplug the projector from power before lamp

installation or replacement and wait for it to

cool.

Lock the yoke before fitting/replacing the lamp.

Loosen 8 fast-fit screws and remove the back

cover,

you can see the structure as shown in the figure

2..

After unplug the power wires, hold the end of

the lamp and push it as directed by the arrow

resulting in the other end of the lamp

unblocked ,then pull the lamp out. Before

installing new lamp, plug the power wires for the

lamp tightly. Installation of the lamp is an reverse

sequence to the pull-out.

Fit new lamp and close the back cover by fastening 8 fast-fit screws. Note: don’t touch the bulb of the new lamp with

bare hand so as not to influence the beam output; Do not harm the sticking out point of the lamp during its installation.

WARNING: Care should always be taken when handling these lamps. Always read the manufacturers

"Instructions for use" enclosed with the lamp.

CONTROL

PANEL

CLAMP

HANDLE

SAFETY CORD

106

WARNING

To pass 1 SAFETY CORD

through 2 holes for safety

FAST-FIT SCREWS

LAMP

5/20

POWER SUPPLY-MAINS

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked

on the panel of the projector. It is recommended that each projector be supplied separately so that they may be

individually switched on and off.

IMPORTANT

It is essential that each projector is correctly earthed(yellow/green twin wire) and the electrical installation

conforms to all relevant standards.

CONTROL CONNECTION

Connection between controller and projector and between one projector and another must be made with a 2

core-screened cable, with each core having at least a 0.5mm diameter. Connection to and from the projector is via

cannon 3 pin (which are included with the projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown

in the figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of

the plug is not connected in any way other than as shown above. The projector accepts digital control signals in protocol

DMX512 (1990).

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input

and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown

in the figure below.

TO CONTROLLER

DMX512 DMX IN DMX OUT

TO TERMINATER

DMX IN DMX OUT DMX IN DMX OUT

6/20

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This

prevents electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2 and 3, which is

then plugged into the output socket on the last projector in the chain. The connections are illustrated below.

SETUP OPTIONS-PROJECTOR CONFIGURATION

Projector configuration can be set conveniently via switch button and LCD display. Turn the projector on and the LCD

display will show DMX address you set and save last time and it can be reset and saved again as you please.

Launch the projector. Press button ENTER more than 5 seconds to unlock panel. After this, the display shows the

projector’s function menu and each option has its own sub-menus. Each menu stands for special function, see details as

follows.

Press button UP or DOWN if you want to browse through the various Setup Options.

Press button ENTER to save your settings or enter the next menu. Press button UP or DOWN to change the

values(plus or minus)

Press button FUNC, it will return to the upper menu one by one. If the button not pressed, defaulted will show display

status automatically.

TO SET THE DMX START ADDRESS

Each projector must be given a DMX start address so that the correct projector responds to the correct control signals.

This DMX start address is the channel number from which the projector starts to “listen” to the digital control information

being sent out from the controller. XR 200 BEAM has 2 DMX modes. There are standard mode and short mode. For

example standard mode have 14 channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 015, No.

3 projector’s address 029, No. 4 projector’s address 043, and so on.

Launch the projector. Press button ENTER more than 5 seconds to unlock panel.

Press button ENTER to display DMX address;

Press button UP and DOWN, you can set the address;

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

7/20

Press button ENTER to confirm; after powered next time, It will display latest values.

Press button FUNC, it will return to the upper menu one by one.

STAND-ALONE MODE

Operate the projector without connecting a controller, enable the master mode in the operation panel, the

projector will run in Stand-Alone mode automatically.

MASTER/SLAVE MODE

Without using a controller, many projectors can run synchronously in the Master/Slave mode by linking them

with each other. Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the

second fixture’s input and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX

terminator as shown in the figure below. Then the first one is the master with setting options as master mode

enabled, and others are slaves.

Start Address for all slaves is 001. The Master can run at any mode for the Master and Slaves run at the

corresponding mode compared to the Master.

After powered , the group will run at Master/Slave Mode.

OPERATION MENU

1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL

AddR XX

(

1~512

)

CNFG

(Config Settings)

dmX

(DMX Mode

,Default: STD)

(

DMX Mode Standard

)

(

DMX Mode Shor

)

LA-C

(Lamp Control

,Default: CHAN)

CHAN

(By Control Channel)

(

Power

)

xyCH

(Pan Tilt Swap,

Default: OFF)

xyCP

(Pan Tilt Invert,

Default: OFF)

mOR

(Master/Slave Options,

Default: SLAV

)

SLAV

(Slave)

mAST

(Master 1)

INPUT OUTPUT

MASTER SLAVE SLAVE

INPUT OUTPUT INPUT DMXTERMINATOR

8/20

FACT

（Factory Default Settings?）

yES

TRmd

(Parameters transmitted(2)?)

yES

INFO

(Information)

TImE

(Lighting Fixture Use Time) XXXX

(Time displayed)

TLAM

(Lamp Use Time)

XXXX

(Time displayed)

VER

(Version No.) X.X.X

(Software Version No.)

TEST

(Test Modes)

STOB

(Strobe)

(Without Strobe)

STO1

(Strobe 1)

STO2

(Strobe 2)

COwH

(Color Wheel)

(White)

Cw1-CW1

(Color Wheel1-Color

Wheel14

)

FORw

(Rotation)

STOP

(Rotation Stops)

REVE

(reverse Rotation)

FGwH

(Fixed Gobo Wheel)

(White)_

FGw1-FGW17

(Gobo1-Gobo17)

FORw

(Rotation)

REVE

(Reverse Rotation)

GWS1-GWS10

(Shake Effect 1-10)

PRIS

(Prism)

(Prism not used)

PR!

(Effect 1)

PR2

(Effect 2)

PR3

(Effect 3)

PR4

(Effect 4)

PRRO

(Prism Rotation)

STOP

(Rotation Stops)

FORw

(Rotation)

REVE

(Reverse Rotation)

FOCU

(Focus) 0-255

(Linear Focusing)

PAN 0-255

TILT 0-255

X&YS

(PAN and Tilt Speeds) 0-255

RESE

(Reset?) Yes

9/20

(Operating Menu)

Dmx

(DMX Mode)

PR XX

(Preset Memory,PR01-PR16)

ET XX

(User Memory,ET01~ET16）

CH1

(Strobe) 0-255

CH2

(Dimming) 0-255

CH3

(Color Wheel) 0-255

CH4

(Fixed Gobo Wheel) 0-255

CH5

(Prism Wheel) 0-255

CH6

(Prism Rotation) 0-255

CH7

(Focusing) 0-255

CH8

(Pan) 0-255

CH9

(Tilt) 0-255

CH10

(Pan and Tilt Speeds) 0-255

CH11

Scene hold time

0-255

Time=X*40mS

LAMP

（Manual Ignition）

L-ON

(Lamp ON) YES

L-OF

(Lamp Off) YES

Remark:

1. In the synchronous control of multiple projectors parameters can be transmitted from the master including:

DMX mode, display setting, operation mode(user memory);

2. all projectors Accepting parameters will automatically be set to slave mode.

REPLACING GOBOS

Disconnect the fixture from power. Lock Tilt. Carefully lift off the cover by unfastening the 4 screws and see the structure

shown as above..

COLOR WHEEL GOBO WHEEL

10/20

For the replacement of color wheels, it can be directly taken off by hands with due care. New color filters must be tightly

glued in right direction to the color wheel..

Gobo Replacement: Gobo wheel is taken off in the same direction as color wheel after it is taken off by hand. After the

new gobos are tightly inserted into the gobo wheel in the right direction and fixed gobo wheels installed, then the color

wheel should be re-installed.

Note: Color filter must not be touched by hands, it should be touched with glabrous, clean and soft tissue or cloth matted

between hand and glass instead of with bare hand.

Close the rear cover and fasten 4 screws and unlock tilt.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PR Lighting Beleuchtungsausrüstung Handbücher

PR Lighting

PR Lighting PR-8121 Bedienungsanleitung

PR Lighting

PR Lighting PR-2330 Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 3000-W FRAMING Bedienungsanleitung

PR Lighting

PR Lighting LS150 TREE Bedienungsanleitung

PR Lighting

PR Lighting AQUA 350 BEAM Bedienungsanleitung

PR Lighting

PR Lighting CHAMELEON PR-2012H Bedienungsanleitung

PR Lighting

PR Lighting XR130 Beam Bedienungsanleitung

PR Lighting

PR Lighting CENTURY SPOT PR-2002 Bedienungsanleitung

PR Lighting

PR Lighting PR-6000 FRAMING Bedienungsanleitung

PR Lighting

PR Lighting XR 230 Beam Bedienungsanleitung

PR Lighting

PR Lighting XPAR 354 Bedienungsanleitung

PR Lighting

PR Lighting PR-8120 Bedienungsanleitung

PR Lighting

PR Lighting Junior JNR-8142D Bedienungsanleitung

PR Lighting

PR Lighting PR-8920 Bedienungsanleitung

PR Lighting

PR Lighting XL 1500 Bedienungsanleitung

PR Lighting

PR Lighting XL WASH 700 Bedienungsanleitung

PR Lighting

PR Lighting TANGO SPOT Bedienungsanleitung

PR Lighting

PR Lighting XLED 590 Bedienungsanleitung

PR Lighting

PR Lighting XL 1500 Bedienungsanleitung

PR Lighting

PR Lighting AQUA 580 BWS Bedienungsanleitung

PR Lighting

PR Lighting XPar 150 Zoom Bedienungsanleitung

PR Lighting

PR Lighting PR-8836 Bedienungsanleitung

PR Lighting

PR Lighting PR-2001L Bedienungsanleitung

PR Lighting

PR Lighting PR-8846 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung