ProLights EclSoft LinearIP Bedienungsanleitung
USER MANUAL
REV.01-09/22 English version
EclSoft LinearIP
IP65, 250W Tunable White and colourful linear
LED soft light with pixels and lighting effects
Thank you for choosing PROLIGHTS
Please note that every PROLIGHTS product has been designed in Italy to meet quality and performance requirements
for professionals and designed and manufactured for the use and application as shown in this document.
Any other use, if not expressly indicated, could compromise the good condition/operation of the product and/or be
a source of danger.
This product is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively
applicable national accident prevention rules and regulations.
Features, specications and appearance are subject to change without notice. Music & Lights S.r.l. and all afliated
companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other
loss occasioned by the use of, inability to use or reliance on the information contained in this document.
Product user manual can be downloaded from the website www.prolights.it , or can be inquired to the ofcial
PROLIGHTS distributors of your territory (https://www.prolights.it/sales_network.html).
Scanning the below QR Code, you will access the download area of the product page, where you can nd a broad
set of always updated technical documentation: specications, user manual, technical drawings, photometrics,
personalities, xture rmware updates.
The PROLIGHTS Logo, PROLIGHTS names and all other trademark in this document pertaining to PROLIGHTS services
or PROLIGHTS product are trademarks OWNED or licensed by Music & Lights S.r.l., its afliates, and subsidiaries.
PROLIGHTS is a registered trademark by Music & Lights S.r.l. All right reserved. Music & Lights – Via A. Olivetti, snc -
04026 - Minturno (LT) ITALY.
Visit the download area
of the product page
PROLIGHTS - EclSoft LinearIP 01
INDEX
SAFETY INFORMATION 02
1 - PACKAGING 05
PACKAGE CONTENT..................................................................................................... 05
OPTIONAL ACCESSORIES............................................................................................. 05
2 - TECHNICAL DRAWING 05
3 - INSTALLATION 06
MOUNTING.................................................................................................................... 06
4 - CONNECTION TO THE MAINS SUPPLY 08
5 - START UP 08
CONNECT AND DISCONNECT POWER FROM THE PRODUCT.................................. 08
6 - PRODUCT OVERVIEW 09
7 - DMX CONNECTION 10
CONNECTION OF THE CONTROL SIGNAL: DMX LINE .............................................. 10
INSTRUCTIONS FOR A RELIABLE DMX CONNECTION ............................................... 10
CONNECTION DAISY CHAIN........................................................................................ 10
CONNECTION OF THE DMX LINE................................................................................ 10
CONSTRUCTION OF THE DMX TERMINATION ........................................................... 11
DMX ADDRESSING ........................................................................................................ 11
ETHERNET CONNECTION ............................................................................................ 11
ETHERNET OPERATION ................................................................................................ 11
ETHERNET TO DMX OPERATIONS ............................................................................... 12
OPERATION AS A WIRELESS TRANSMITTER................................................................ 12
IN TO WDMX ................................................................................................................. 12
OPERATION AS A WIRELESS RECEIVER........................................................................ 13
WDMX TO DMX (RX)...................................................................................................... 13
8 - CONTROL PANEL 14
DISPLAY AND BUTTONS LAYOUT................................................................................. 14
9 - MENU STRUCTURE 15
10 - SHORTCUT 20
11 - RDM FUNCTIONS 21
12 - DMX CHARTS 25
13 - ACCESSORIES INSTALLATION 78
CENTER MOUNT BRACKET (CODE ESLIPBRK - OPTIONAL) ....................................... 78
BALL HEAD JOINT (CODE EPTWCBHEAD - OPTIONAL) ............................................. 79
FOOT PLATE (CODE ESLIPFY - OPTIONAL).................................................................. 80
FRONT INTENSIFIED/ HIGH / MEDIUM / LOW DIFFUSION (CODE ESLIPFILTERINT /
HD / MD / LD - OPTIONAL) ........................................................................................... 81
EGG CRATE (CODE ESLIPEC60 - OPTIONAL).............................................................. 82
14 - TEST OF IP65 RATING 83
15 - MAINTENANCE 84
MAINTENANCE AND CLEANING THE PRODUCT........................................................ 84
VISUAL CHECK OF PRODUCT HOUSING ..................................................................... 84
TROUBLESHOOTING..................................................................................................... 85
PROLIGHTS - EclSoft LinearIP02
SAFETY INFORMATION
WARNING!
• Please read carefully the instruction reported in this section before installing, powering,
operating or servicing the product and observe the indications also for its future handling.
This unit is not for household and residential use, only professional applications.
Connection to mains supply
• The Connection to the mains supply must be carried out by a qualied electrical
installer.
• Use only AC supplies 100-240V 50-60 Hz, the xture must be electrically connected
to ground (earth).
• Select the cable cross section in according with the maximum current draw of the
product and the possible number of products connected at the same power line.
• The AC mains power distribution circuit must be equipped with magnetic+residual
current circuit breaker protection.
• Do not connect it to a dimmer system; doing so may damage the product.
Protection and Warning against electrical shock
• Do not remove any cover from the product, always disconnect the product from AC
power before servicing.
• Ensure that the xture is electrically connected to ground (earth). And use only a
source of AC power that complies with local building and electrical codes and has
both overload and ground-fault (earth-fault) protection.
• Before using the xture, check that all power distribution equipment and cables are
in perfect condition and rated for the current requirements of all connected devices.
• Isolate the xture from power immediately if the power plug or any seal, cover, cable, or
other components are damaged, defective, deformed or showing signs of overheating.
• Do not reapply power until repairs have been completed.
• Refer any service operation not described in this manual to PROLIGHTS Service team
or an authorized PROLIGHTS service center.
Installation
• Make sure that all visible parts of the product are in good visible condition before its
use or installation.
• Make sure the point of anchorage is stable before positioning the projector.
• When suspending the xture above ground level, secure it against failure of primary
attachments by attaching a safety cable that is approved as a safety attachment for
the weight of the xture to the attachment point on the main frame of the product. ln
case the safety cable, enter in action, it needs to be replaced with a new one.
• Install the product only in well ventilated places.
• For non temporary installations, ensure that the xture is securely fastened to a load-
bearing surface with suitable corrosionresistant hardware.
• For a temporary installation with clamps, ensure that the quarter-turn fastener and/or
screws are turned fully, and secured with a suitable safety cable.
0.5 m Minimum distance of illuminated objects
• The projector needs to be positioned so that the objects hit by the beam of light are
at least 0,5 meters (1,64 ft) from the lens of the projector.
T 45°C
a
Max operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) exceeds 45 °C (113 °F).
PROLIGHTS - EclSoft LinearIP 03
T
-20°
C
aMinimum operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) is below -20 °C (-4 °F).
Protection from burns and re
• The exterior of the xture becomes hot during use. Avoid contact by persons and
materials.
• Ensure that there is free and unobstructed airow around the xture.
• Keep ammable materials well away from the xture.
• Do not expose the front glass to sunlight or any other strong light source from any an-
gle. Lenses can focus the sun’s rays inside the xture, creating a potential re hazard.
• Do not attempt to bypass thermostatic switches or fuses.
IP65
Outdoor (temporary) use
• This product is rated with an IP (Ingress protection) for temporary outdoor use when
used and serviced according to the instruction contained in this document.
• Never use the xture in places subject to vibrations or bumps.
• Make certain that no inammable liquids, water or metal objects enter the xture.
• Excessive dust, smoke uid, and particle build up degrades performance, causes
overheating and will damage the xture.
• Damages caused by inadequate cleaning or maintenance are not covered by the
product warranty.
T
70°
C
c
Temperature of the external surface
• The surface of the xture can reach up to 70 °C (158 °F) during operation. Avoid
contact with people and materials.
Maintenance
• Warning! Disconnect the xture from AC mains power and allow to cool for at least
10 minutes before handling.
• Only technicians who are authorized by PROLIGHTS or Authorised service partners
are permitted to open the xture.
• Users may carry out external cleaning, following the warnings and instructions pro-
vided, but any service operation not described in this manual must be referred to a
qualied service technician.
• Important! Excessive dust, smoke uid, and particle build up degrades performance,
causes overheating and will damage the xture. Damages caused by inadequate
cleaning or maintenance is not covered by the product warranty.
Photobiological safety
• This device emits potentially dangerous optical radiation and is identied in the cat-
egory of Risk Group 1 according to EN 62471.
Do not stare at the operating light source
• Do not look directly at the LED source during operation. It can be harmful to the eyes
and skin.
• During Installation, operation and maintenance, be prepared for the xture to light
and move suddenly when connected to power.
Disposal
• This product is supplied in compliance with European Directive 2012/19/EU – Waste
Electrical and Electronic Equipment. (WEEE). To preserve the environment please
dispose/ recycle this product at the end of its life according to the local regulation.
PROLIGHTS - EclSoft LinearIP04
The products to which this manual refers comply with:
• 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD);
• 2014/30/EU - Electromagnetic Compatibility (EMC);
• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS);
• 2014/53/EU - Radio Equipment Directive (RED).
The products to which this manual refers comply with:
• UL 1573 + CSA C22.2 No. 166 - Stage and Studio Luminaires and Connector Strips.
• UL 1012 + CSA C22.2 No. 107.1 - Standard for power units other than class 2.
FCC Compliance:
• This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-
lowing two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation.
Other approvals
• The product meets the safety requirements of the certification procedures of the
market in which it is placed and sold.
PROLIGHTS - EclSoft LinearIP 05
1 - PACKAGING
PACKAGE CONTENT
• 1x ECLSOFTLINEARIP.
• 1x 1,5 meters power cable (BARE END - SEETRONIC IP65 power connector).
• User Manual.
• 2x OS27: quick-Lock omega bracket, M10 hole.
• 1x ESLIPFILTERMD: front medium diffusion lter for ECLSOFTLINEARIP.
OPTIONAL ACCESSORIES
• FCLECLSOFTLIP: ight case for 5 pcs of ECLSOFTLINEARIP.
• ESLIPEC60: egg crate for ECLSOFTLINEARIP.
• ESLIPFILTERINT: front intensied diffusion lter for ECLSOFTLINEARIP.
• ESLIPFILTERHD: front high diffusion lter (less output) for ECLSOFTLINEARIP.
• ESLIPFILTERLD: front low diffusion lter (more output) for ECLSOFTLINEARIP.
• ESLIPFY: foot plate kit with tilt for the ECLSOFTLINEARIP (2 pcs).
• EPTWCBHEAD: ball head joint for center mount bracket EPTWCBRK series.
• ESLIPBRK: center mount bracket for ECLSOFTLINEARIP.
• ESLIPSG50: 50° SnapGrid, for ECLSOFTLINEARIP by DoP choice.
• RSR0630A/B: steel security cable for hanging bodies, inox steel shackle, L=60 cm, silver/black.
• C6002: slim aluminium clamp, 200 kg loading, 48-51 mm tubes, M10 bolt.
• IPTESTBOX: portable vacuum and pressure tester for ProLights IP xtures.
• WSBBR512G5: blackBox R-512 G5 receiver 512Ch, 2.45GHz & 5.8GHz, DMX/RDM optional.
• WSBBF1G6: BlackBox F-1 G6 transrec, 512ch, 2.45GHz, DMX&RDM,Bluetooth,G3,G4,G4S, G5, CRMX.
• WSBBF1G5: blackBox F-1 G5 transmitter, 2,45GHz & 5.2/5,8 GHz, DMX/RDM, 512Ch.
• TOUR53415L03: dmx cable HC5340. CANC5MXX XLR 5p->CANC5FXX XLR (f) 5p, L.3m.
• 958225L03: 3x2.5mm TH07 Cable, 16A 3p PwCon MXW, 16A 3p PwCon FXW, L. 3m.
• 9513FXWL03: ass. 3x2.5mm TH07 cable, 16A 3p 230V CEE plug, MENAC3FXW socket, L.3 m.
• 9533FXWL03: ass. 3x2.5mm TH07 cable, SHUKO plug, MENAC3FXW socket, L.3m.
• WSBBR512G6: blackBox R-512 G6 receiver 512Ch, 2.45GHz,DMX&RDM,Bluetooth,G3,G4,G4S,G
5,CRMX.
• UPBOX1UP5: rmware uploader kit, USB IN, 5pin XLR DMX OUT, USB OUT.
119 mm
[4.7in]
1000 mm
[39.4in]
85 mm
[3.3in]
Fig. 01
Weight: 7.1 kg - 15.65 lbs
2 - TECHNICAL DRAWING
PROLIGHTS - EclSoft LinearIP06
Fig. 02
3 - INSTALLATION
MOUNTING
Check that the supporting structure can safely bear the weight of all installed xtures, clamps, cables,
auxiliary equipment, etc. and complies with locally applicable regulations.
When suspending the xture above ground level, secure it against failure of primary attachments by
attaching a safety wire that is approved as a safety attachment for the weight of the xture to an anchor
point on the product main frame.
Do not use removable parts or weak anchors for secondary attachment.
Warning! When clamping the xture to a truss or other structure at any angle, use clamps of half-cou-
pler type. Do not use any type of clamp that does not completely encircle the structure when fastened.
C6002
clamp
RSR0630A/B
Steel security cable
OS27
Quick-lock
C6002
clamp
OS27
Quick-lock
107 mm
4,21 in
107 mm
4,21 in
PROLIGHTS - EclSoft LinearIP 07
12
Fig. 03
C6002
clamp
C6002
clamp
C6002
clamp
RSR0630A/B
Steel security cable
OS27
Quick-lock
OS27
Quick-lock
OS27
Quick-lock
RSR0630A/B
Steel security cable
PROLIGHTS - EclSoft LinearIP08
5 - START UP
CONNECT AND DISCONNECT POWER FROM THE PRODUCT
To apply and disconnect power to the product:
• Check that the product is installed and secured as indicated in the Safety Informations, and that
personal safety will not be put at risk when the xture lights up.
• Connect the power connector into the Mains input socket (100-240 VAC-50/60 Hz).
• The product is then ready for its operations and can be controlled through the available input sig-
nals on board.
• To disconnect power from the product, disconnect the Mains from the socket.
4 - CONNECTION TO THE MAINS SUPPLY
WARNING: For protection from electric shock, the xture must be earthed!
The product is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz
AC power source from 100-240 Volts.
If you need to install a power plug on the power cable to allow connection to power outlets, install a
grounding-type (earthed) plug, following the plug manufacturer’s instructions. If you have any doubts
about proper installation, consult a qualied electrician.
The max power consumption is 250W.
Core (EU) Core (US) Connection Plug terminal marking
Brown Black Live L
Blue White Neutral N
Yellow+green Green Earth
Inhaltsverzeichnis
Andere ProLights DJ-Equipment Handbücher
ProLights
ProLights V575WASH Bedienungsanleitung
ProLights
ProLights RADIONSTR Bedienungsanleitung
ProLights
ProLights RA3000Profile Bedienungsanleitung
ProLights
ProLights ASTROBEAM Bedienungsanleitung
ProLights
ProLights Eclipse FC Bedienungsanleitung
ProLights
ProLights SMARTBATHEX Bedienungsanleitung
ProLights
ProLights DISPLAYCOBTRWDFC Bedienungsanleitung
ProLights
ProLights SmartBat Wash Bedienungsanleitung
ProLights
ProLights SUNPIX24TRI Bedienungsanleitung
ProLights
ProLights ARCPOD27Q Bedienungsanleitung
ProLights
ProLights TRIBE TRUSSPOD3T Bedienungsanleitung
ProLights
ProLights AIR5FAN Bedienungsanleitung
ProLights
ProLights QUADMOON Bedienungsanleitung
ProLights
ProLights LUMIPAR12HPRO Bedienungsanleitung
ProLights
ProLights ECLIPSE FRESNEL TU Bedienungsanleitung
ProLights
ProLights LUMIPAR12UAW Bedienungsanleitung
ProLights
ProLights JETSPOT-3 Bedienungsanleitung
ProLights
ProLights EMERALD Bedienungsanleitung
ProLights
ProLights LEDPAR64363RGB Bedienungsanleitung
ProLights
ProLights 6BEAMQ Bedienungsanleitung
Beliebte DJ-Equipment Handbücher anderer Marken
thomann
thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung
Eagletone
Eagletone 6 Eyes Flower Bedienungsanleitung
EuroLite
EuroLite FLD-1508 Bedienungsanleitung
Technical Pro
Technical Pro LG8xSEA Bedienungsanleitung
JB Systems
JB Systems Lounge Laser DMX Bedienungsanleitung
Lightmaxx
Lightmaxx Vega Halo 90 Bedienungsanleitung
Elation
Elation FUZE WASH Z350 Bedienungsanleitung
Maverick
Maverick MK3 WASH Bedienungsanleitung
Infinity
Infinity TF-260C7 Fresnel Bedienungsanleitung
Chauvet
Chauvet EVE E-50Z Bedienungsanleitung
Eliminator Lighting
Eliminator Lighting E 138 Bedienungsanleitung
EuroLite
EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung