Radio Shack 43-3505 Bedienungsanleitung

RadioShack and RadioShack.com are trademarks

used by RadioShack Corporation.

OWNER’S MANUAL — Please read before using this equipment.

900 MHz Cordless Telephone

with 10 Memory Speed Dial

FEATURES

Your RadioShack 900 MHz Cordless Phone offers the latest ad-

vances in cordless phone technology. Its headset jack lets you

connect an optional headset for hands-free convenience while

you use the phone. The base’s space-saving design makes it per-

fect for areas where space is limited.

Your phone has these features:

Ample Talk and Standby Time — when fully charged (about 12

hours), the supplied battery provides about 7 hours of talk time or

7 days of standby time.

Security Access-Protection Code — prevents other cordless

phone users from using your phone line while the keypad is off the

base.

10-Memory Speed Dial — stores up to 10 frequently called

phone numbers for easy dialing.

10-Channel Auto Scan — automatically selects a clear channel

when you make or answer a call.

Hearing-Aid Compatibility — lets you use your phone with hear-

ing aids that have a T (telephone) switch.

43-3505.fm Page 1 Monday, August 7, 2000 4:58 PM

Headset Jack — lets you connect an optional headset (available

at your local RadioShack store) for hands-free convenience.

Volume Control — lets you control the volume of the sound you

hear through the handset.

Page — lets you send a paging signal from the base to the hand-

set to help locate a misplaced handset or page someone at the

handset.

Your phone is ETL listed to UL standards and meets all applicable

FCC standards.

WARNING: To reduce the risk of fire or shock hazard, do not ex-

pose this product to rain or moisture.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER OR BACK. NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSON-

NEL.

This symbol is intended to alert you to the pres-

ence of uninsulated dangerous voltage within the

product’s enclosure that might be of sufficient

magnitude to constitute a risk of electric shock.

Do not open the product’s case.

43-3505.fm Page 2 Monday, August 7, 2000 4:58 PM

READ THIS BEFORE INSTALLATION

Each device that you connect to the phone line draws power from

the phone line. We refer to this power draw as the device’s ringer

equivalence number, or REN. The REN is on the bottom of the

base.

If you are using more than one phone or other device on the line,

add up all the RENs. If the total is more than five (three in rural ar-

eas), your phone might not ring. If ringer operation is impaired, re-

move a device from the line.

FCC STATEMENT

This telephone complies with Part 68 of the

FCC Rules

. You must,

upon request, provide the FCC registration number and the REN

to your phone company. These numbers are on the bottom of the

base.

Compatible jacks for this phone are RJ11C and RJ11W, available

at your local RadioShack store.

Note: You must not connect your phone to any of the following:

• coin-operated systems

• party-line systems

• most electronic key phone systems

This symbol is intended to inform you that impor-

tant operating and maintenance instructions are

included in the literature accompanying this prod-

uct.

43-3505.fm Page 3 Monday, August 7, 2000 4:58 PM

THE FCC WANTS YOU TO KNOW

In the unlikely event that your phone causes problems on the

phone line, the phone company can temporarily discontinue your

service. If this happens, the phone company attempts to notify you

in advance. If advance notice is not practical, the phone company

notifies you as soon as possible and advises you of your right to

file a complaint with the FCC.

Also, the phone company can make changes to its lines, equip-

ment, operations, or procedures that could affect the operation of

this telephone. The telephone company notifies you of these

changes in advances, so you can take the necessary steps to pre-

vent interruption of your telephone service.

This equipment complies with the limits for a Class B digital de-

vice as specified in Part 15 of the

FCC Rules

. These limits provide

reasonable protection against radio and TV interference in a resi-

dential area. However, your equipment might cause TV or radio

interference even when it is operating properly. To eliminate inter-

ference, you can try one or more of the following corrective mea-

sures:

• Reorient or relocate the receiving antenna.

• Increase the distance between the equipment and the radio

or TV.

• Use outlets on different electrical circuits for the equipment

and the radio or TV.

Consult your local RadioShack store if the problem still exists.

43-3505.fm Page 4 Monday, August 7, 2000 4:58 PM

LIGHTNING

You telephone has built-in lightning protection to reduce the risk of

damage from surges in telephone line and power line current. This

lightning protection meets or exceeds FCC requirement. Howev-

er, lightning striking the telephone or power lines can damage

your telephone.

Lightning damage is not common. Nevertheless, if you live in an

area that has severe electrical storms, we suggest that you unplug

your phone when storms approach to reduce the possibility of

damage.

PREPARATION

Mounting the Phone

You can place the phone on a desk or table, mount it on a stan-

dard wall plate, or mount it directly on a wall.

Select a location that is:

• near an easily accessible AC outlet

• near a telephone line jack

• out of the way of normal activities

• away from electrical machinery, electrical appliances, metal

walls, filing cabinets, wireless intercoms, security alarms, and

room monitors

The base’s location affects the phone’s range. If you have a

choice of several locations, try each to see which provides the

best performance.

43-3505.fm Page 5 Monday, August 7, 2000 4:58 PM

Caution: The supplied AC adapter was designed specifically for

your phone. Use only the supplied adapter.

Notes:

• Your telephone connects directly to a modular telephone line

jack. If your phone line jack is not a modular jack, you can

update the wiring yourself, using jacks and adapters available

at your local RadioShack store. Or, you can let the phone

company update the wiring for you.

• The USOC number of the jack to be installed is RJ11C.

On a Desk

You can power the base using the supplied 12V, 200 mA AC/DC

adapter.

Cautions:

You must use a Class 2 power source that supplies

12V DC and delivers at least 200 mA. Its center tip

must be set to positive and its plug must fit the

phone's DC 12V 200mA jack. The supplied adapter meets

these specifications. Using an adapter that does not meet

these specifications could damage the phone or the adapter.

• Always connect the AC adapter to the phone before you con-

nect it to AC power. When you finish, disconnect the adapter

from AC power before you disconnect it from the phone.

43-3505.fm Page 6 Monday, August 7, 2000 4:58 PM

Follow these steps to place the base on a desk or table using the

supplied bracket.

1. Insert the bracket’s tabs into the base’s upper tab slots as

shown, then press down on the bracket’s clips and insert

them into the clip slots.

2. Plug one end of the supplied modu-

lar cord into the TEL LINE jack on

the back of the base.

3. Plug the modular cord’s other end

into a modular phone line jack.

4. Insert the supplied AC adapter’s barrel plug into the DC 12V

200mA jack on the back of the base.

5. Route the adapter’s cord through the strain relief slot on the

bracket.

6. Plug the adapter into a standard AC outlet.

7. Lift the base’s antenna to a vertical position.

On a Wall Plate or Wall

1. Insert the supplied bracket’s tabs into the base’s lower tab

slots, then press down on the bracket’s clips and insert them

into the clip slots.

2. Plug one end of the supplied short modular cord into the TEL

LINE jack on the back of the base.

3. Insert the supplied AC adapter’s barrel plug into the DC 12V

200mA jack on the back of the base.

TEL LINE

DC 12V

200mA Jack

43-3505.fm Page 7 Monday, August 7, 2000 4:58 PM

4. Route the adapter’s cord through the narrow groove on the

bottom of the bracket.

5. Plug the modular cord into the wall plate jack, then align the

bracket’s keyhole slots with the wall plate studs and slide the

base downward to secure it.

6. Plug the adapter into a standard AC outlet.

7. Press and lift out the handset holder, turn it over and upside

down so its tabbed edge faces up, then slide it back down

into its slot.

8. Lift the base’s antenna to a vertical position.

Note: To mount the phone directly on a wall, you need two screws

(not supplied) with heads that fit into the keyhole slots on the bot-

tom of the base.

Follow the steps under “On a Wall Plate or Wall” on Page 7, then

apply these additional instructions.

1. Drill two holes 315/16 inches (100 mm) apart.

Then thread a screw into each hole, letting the

heads extend about 5/16 inch (8 mm) from the

wall.

2. Plug one end of the supplied long modular

cord into the TEL LINE jack on the back of the

base.

315/16"

5/16"

43-3505.fm Page 8 Monday, August 7, 2000 4:58 PM

3. Align the keyhole slots with the mounting screws and slide

the base downward to secure it.

Connecting, Charging, and

Replacing the Battery Pack

The phone comes with a rechargeable nickel-cadmium battery

pack. You must connect the battery pack and charge it for at least

12 hours before you use the phone for the first time.

1. Press down and slide off the battery pack compartment cover.

2. Unfasten the retainer strap and lift the battery pack out of the

compartment.

3. Plug the battery pack’s connector into the socket in the com-

partment (the connector fits only one way), then replace the

battery pack and fasten the retainer strap.

43-3505.fm Page 9 Monday, August 7, 2000 4:58 PM

4. Replace the cover.

To charge the battery pack, place the handset either faceup or

facedown on the base. The CHARGE/IN USE indicator lights.

Notes:

• Recharge the battery pack if the handset beeps and the IN

USE/LOW BATT indicator on the handset flashes while you

are using the phone, or if the IN USE/LOW BATT indicator

flashes when the phone is not in use.

• When you first use the phone after charging or recharging the

battery pack, the phone might not work. Return the keypad to

the base for about 5 seconds to reset the security access-

protection code.

• About once a month, fully discharge the battery pack by

keeping the phone off the base until the low battery warning

tone sounds. Otherwise, the battery pack loses its ability to

fully recharge.

• If the CHARGE/IN USE indicator does not light when you

place the handset on the base, be sure the battery pack and

AC adapter are correctly and securely connected. Also,

check the charging contacts on the handset and base. If the

contacts are dirty or tarnished, clean them with a pencil

eraser.

• If the battery pack becomes completely discharged or the

base loses power while the handset is away from it, place the

handset on the base for about 5 seconds to reset the security

access-protection code. If the handset loses power, leave it

on the base to charge the battery pack.

43-3505.fm Page 10 Monday, August 7, 2000 4:58 PM

Inhaltsverzeichnis

Andere Radio Shack Schnurloses Telefon Handbücher

Radio Shack

Radio Shack 43-3526 Bedienungsanleitung

Radio Shack

Radio Shack 43-3701 Bedienungsanleitung

Radio Shack

Radio Shack 43-3871 Bedienungsanleitung

Radio Shack

Radio Shack ET-557 Bedienungsanleitung

Radio Shack

Radio Shack 2.4 GHz Digital Spread Spectrum Cordless Telephone with Caller ID/Call Waiting... Bedienungsanleitung

Radio Shack

Radio Shack ET-542 Bedienungsanleitung

Radio Shack

Radio Shack pmn Bedienungsanleitung

Radio Shack

Radio Shack ET-689 Bedienungsanleitung

Radio Shack

Radio Shack 43-3814 Bedienungsanleitung

Radio Shack

Radio Shack 43-5560 Bedienungsanleitung

Radio Shack

Radio Shack Cordless Phone Bedienungsanleitung

Radio Shack

Radio Shack 900 MHz Digital Spread Spectrum Dual Keypad Cordless Telephone with Caller ID/Call Waiting... Bedienungsanleitung

Radio Shack

Radio Shack 43-3570 Bedienungsanleitung

Radio Shack

Radio Shack RT-551 Bedienungsanleitung

Radio Shack

Radio Shack ET-551 Bedienungsanleitung

Radio Shack

Radio Shack ET-518 Bedienungsanleitung

Radio Shack

Radio Shack ET-548 Bedienungsanleitung

Radio Shack

Radio Shack 43-1088 Bedienungsanleitung

Radio Shack

Radio Shack 43-3557 Bedienungsanleitung

Radio Shack

Radio Shack 43-141 Bedienungsanleitung

Radio Shack

Radio Shack 5.8 GHz Multi-Handset Expandable Cordless Telephone with Digital... Bedienungsanleitung

Radio Shack

Radio Shack ET-926 Bedienungsanleitung

Radio Shack

Radio Shack ET-1123 Bedienungsanleitung

Radio Shack

Radio Shack TAD-794 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung