ResMed Lumis HFT Bedienungsanleitung

User guide

English 1

ENGLISH

Welcome

The Lumis™ HFT is a humidifier with an integrated flow generator that delivers warmed and

humidified respiratory gases to spontaneously breathing patients through a nasal cannula.

WARNING

•Read this entire guide before using the device.

•Use the device according to the intended use provided in this guide.

•The advice provided by the prescribing physician should be followed ahead of the

information provided in this guide.

•This device is not suitable for life support patients.

Indications for use

The Lumis HFT device is for the treatment of spontaneously breathing patients who would benefit

from receiving high flow warmed and humidified respiratory gases. The flow may be from

15-40 L/min.

The Lumis HFT is for patients > 30 kg in homes, hospitals and long-term care facilities.

The humidifier is intended for single patient use in the home environment and re-use in a

hospital/institutional environment.

Intended patient population/medical conditions

Obstructive pulmonary diseases (eg, Chronic Obstructive Pulmonary Disease) and chronic cough

with mucous production (bronchiectasis).

Contraindications

High flow therapy may be contraindicated in some patients with the following pre-existing

conditions:

•patients with a level of acuity that would experience injury from loss of therapy (e.g. acute

respiratory failure, acute respiratory distress)

•blocked nasal passages/choanal atresia

•trauma/surgery to nasopharynx

•invasive use.

Adverse effects

You should report unusual chest pain, severe headache, or increased breathlessness to your

prescribing physician. An acute upper respiratory tract infection may require temporary

discontinuation of treatment.

The following side effects may arise during the course of therapy with the device:

•drying of the nose, mouth or throat

•nosebleed

•bloating

•skin rashes.

At a glance

The Lumis HFT includes the following:

•Device

•HumidAir™humidifier

•ClimateLineAir™heated air tubing

•Tubing wrap

•Low Pressure Oxygen connector

•Power supply unit

•Travel bag

•SD card (already inserted).

Contact your care provider for a range of accessories or accessory replacements available for use

with the device including:

•HumidAir humidifier

•ClimateLineAir heated air tubing

•Filter: Hypoallergenic filter, standard filter

•Air10™DC/DC converter (12V/24V)

•SD card reader

•Air10 oximeter adapter

•Air10 USB adapter

•Power Station II

English 3

About your device

1 Air outlet 6 Screen

Air filter cover

Adapter cover

3 Power inlet 8 SD card cover

Serial number and device number

Low flow oxygen input (up to 10 L/min)

5 HumidAir humidifier

About the control panel

Start/Stop button

Press to start/stop therapy.

Press and hold for three seconds to enter power save

mode.

Dial

Turn to navigate the menu and press to select an option.

Turn to adjust a selected option and press to save your

change.

Home button Press to return to the Home screen.

Different icons may be displayed on the screen at different times including:

Humidity Wireless signal strength (green)

Humidifier warming Wireless transfer not enabled (grey)

Humidifier not enabled No wireless connection

Tube drying Airplane Mode

Setup

CAUTION

•Only use nasal cannula with Lumis HFT, do not use full face masks.

•Do not overfill the humidifier as water may enter the device and air tubing.

•To avoid heated water flowing down the tube to the patient:

oplace the device lower than the level of the patient’s head;

oensure the device is placed on a stable surface.

1. With the device on a stable level surface below head height, connect one end of the power cord

into the power supply unit and the other end into the power outlet.

2. Fit the tubing wrap around the air tubing.

See the tubing wrap user guide for detailed information. Humidification performance will be

reduced if the tubing wrap is not fitted.

3. Connect the air tubing firmly to the air outlet located on the rear of the device.

4. Open the humidifier and fill it with water up to the maximum water level mark.

Do not fill the humidifier with hot water.

5. Close the humidifier and insert it into the side of the device.

English 5

6. Connect the free end of the air tubing firmly onto the nasal cannula.

See the nasal cannula user guide for detailed information.

Recommended nasal cannulas are available on ResMed.com/support.

Recommended water type

The following water types are recommended for use in the humidifier:

•Boiled tap water, cooled to room temperature

•Distilled water

•Bottled water (with a low mineral content).

Note: Do not use non-sterile demineralised water for domestic use.

Adding supplemental oxygen

Your Lumis HFT device is designed to be compatible with levels of supplemental oxygen up to 10

L/min.

WARNING

•Always make sure that the device is turned on and airflow generated before the oxygen

supply is turned on. Always turn the oxygen supply off before the device is turned off, so

that unused oxygen does not accumulate within the device enclosure and create a risk of

fire.

•Supplemental oxygen must not be used while smoking or in the presence of an open

flame.

•Supplemental oxygen must only be added into your device oxygen inlet at the rear of the

device. Adding oxygen elsewhere, ie, into the breathing system via tube, will affect the

delivered flow volume, temperature and humidity.

CAUTION

Do not connect supplemental oxygen input directly to a medical gas pipeline system, oxygen

bottle or other high pressure oxygen source. A flow regulator must be fitted to ensure the

delivered oxygen remains at or below 10 L/min.

For advice on connecting to an oxygen source, contact your homecare provider.

To add supplemental oxygen:

1. Unlock the low flow oxygen input at the rear of the device by pushing down on the locking clip.

2. Insert one end of the oxygen supply tubing into the low flow oxygen input. The tubing will

automatically lock into place.

3. Attach the other end of the oxygen supply tubing to the oxygen supply.

4. Start therapy.

5. Turn on oxygen and adjust (at the oxygen supply) to the prescribed flow rate.

To remove supplemental oxygen:

1. Unlock the low flow oxygen input at the rear of the device by pushing down on the locking clip.

2. Remove the oxygen port connector from the low flow oxygen input.

Performing a functional check

With the device powered off:

•Check the condition of the device and accessories.

Inspect the device and all the provided accessories. If there are any visible defects, the system

should not be used.

•Check the air tubing setup.

Check the integrity of the air tubing. Connect the air tubing firmly to the air outlet and other

accessories if in use.

•Check the connection to the oxygen port.

Inspect the connection for cracks or leaks and that the port is stable.

•Check the HumidAir humidifier.

Inspect the humidifier for cracks or leaks. If there are any visible defects, the humidifier should

be replaced.

English 7

Starting therapy

Warmup mode

Warmup mode pre-heats the water before starting therapy so that the air is not cold or dry at the

start of therapy. It is recommended that Warmup mode be run before starting therapy.

Depending on the ambient conditions, the Lumis HFT device will take between 10 to 20 minutes to

warm up. Therapy can be started any time during Warmup mode. After Warmup mode has been

running for 40 minutes, the device will automatically switch to Drying mode.

To run warmup mode:

Select Run Warmup.2.

Warmup will take between

10-20 mins. Therapy can be

started at any time during

Warmup.

When Warmup is complete,

Ready will be displayed.

Start therapy

4. Fit your high-flow nasal

cannula. See your nasal

cannula user guide for fitting

instructions.

5. Press the Start/Stop button

to start therapy.

6. If you have supplemental

oxygen, ensure source is

now turned ON.

You will know that therapy is on when the Monitoring screen is displayed.

The FLOW bar shows the current flow setting in green.

The screen will go black automatically after a short period of time. You can press Home or the dial to

turn it back on. If power is interrupted during therapy, the device will automatically restart therapy

when power is restored.

The Lumis HFT device has a light sensor that adjusts the screen brightness based on the light in the

room.

Note: Consider placing device on heat resistant pad to avoid possible heat damage to surfaces.

Expected duration of operation between refills

Flow Setting vs therapy duration#

L/min 15 20 25 30 35 40

hrs 16 12 10 9 8 7

# Tested at Humidity - Level 3, tube temperature 37°C, and ambient temperature 23°C

Stopping therapy

Ensure oxygen source is

turned OFF.

Remove your high-flow nasal

cannula.

Press the Start/Stop button

and then press the dial to

confirm Yes to stop therapy.

English 9

Drying mode

After stopping therapy, Drying mode will automatically start. This mode dries

the air tube and cannula so that it is ready for use next time.

During Drying mode, do not remove the humidifier water tub. The device will

automatically enter standby after 90 minutes.

While Drying mode is running you can view the Therapy Report by pressing

the Home button.

The device regulates the tube temperature to a medium value, whilst running

the humidifier at minimum power during the Drying mode.

WARNING

•Remove the nasal cannula from your face before starting Drying mode because the air is

dry and may cause harm.

•Turn off supplemental oxygen at the source before starting Drying mode so that oxygen

does not accumulate and create a fire risk.

Power save mode

Your Lumis HFT device records your therapy data. In order to allow it to transmit the data to your

care provider, you should not unplug the device. However, you can put it into power save mode to

save electricity.

To enter power save mode:

•Press and hold Start/Stop for three seconds.

The screen goes black.

To exit power save mode:

•Press Start/Stop once.

The Home screen is displayed.

Andere Handbücher für Lumis HFT

Inhaltsverzeichnis

Sprachen:

Andere ResMed Medizinische Geräte Handbücher

ResMed

ResMed VPAP COPD Bedienungs- und Sicherheitshinweise

ResMed

ResMed AirSense 10 Bedienungsanleitung

ResMed

ResMed AirFit N30 Bedienungsanleitung

ResMed

ResMed AirFit N30 Bedienungsanleitung

ResMed

ResMed S8 ESCAPE System Bedienungsanleitung

ResMed

ResMed stellar series Bedienungsanleitung

ResMed

ResMed Flow Generator AutoSet CS 2 Bedienungsanleitung

ResMed

ResMed Mirage SoftGel Bedienungsanleitung

ResMed

ResMed S9 AutoSet Technisches Handbuch

ResMed

ResMed AIRMINI Abmessungen

ResMed

ResMed airsense 10 autoset Leitfaden

ResMed

ResMed VPAP II Bedienungsanleitung

ResMed

ResMed S9 Series Technisches Handbuch

ResMed

ResMed Ultra Mirage Bedienungsanleitung

ResMed

ResMed Swift FX Bedienungsanleitung

ResMed

ResMed S8 Compact System Bedienungsanleitung

ResMed

ResMed Ultra Mirage II Bedienungsanleitung

ResMed

ResMed AirFit N30i Bedienungsanleitung

ResMed

ResMed AIRMINI Bedienungsanleitung

ResMed

ResMed Ultra Mirage Bedienungsanleitung

ResMed

ResMed S8 Series Bedienungsanleitung

ResMed

ResMed S8 AutoSet Spirit II Bedienungsanleitung

ResMed

ResMed Mirage SoftGel Bedienungsanleitung

ResMed

ResMed Elisee 150 Gebrauchsanweisung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung