Rockwell Automation DeviceNet ArmorBlock A Series Bedienungsanleitung
Installation Instructions
DeviceNet ArmorBlock Network and Auxiliary
Powered Module, Series A
Catalog Number 1732D-8X81212HD
Topic Page
Important User Information 2
Environment and Enclosure 3
Prevent Electrostatic Discharge 3
About the Module 4
Catalog Number Explanation 5
Install the Module 5
Mount the Module 6
Communicate with Your Module 11
Interpret the Status Indicators 12
Specifications 15
2DeviceNet ArmorBlock Network and Auxiliary Powered Module, Series A
Publication 1732D-IN011A-EN-E - April 2009
Important User Information
Solid state equipment has operational characteristics differing from those of electromechanical
equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls
(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at
http://literature.rockwellautomation.com) describes some important differences between solid state
equipment and hard-wired electromechanical devices. Because of this difference, and also because of
the wide variety of uses for solid state equipment, all persons responsible for applying this equipment
must satisfy themselves that each intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages
resulting from the use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the
many variables and requirements associated with any particular installation, Rockwell Automation, Inc.
cannot assume responsibility or liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,
equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell
Automation, Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
WARNING Identifies information about practices or circumstances that can cause an explosion in
a hazardous environment, which may lead to personal injury or death, property
damage, or economic loss.
IMPORTANT Identifies information that is critical for successful application and understanding of
the product.
ATTENTION Identifies information about practices or circumstances that can lead to personal
injury or death, property damage, or economic loss. Attentions help you identify a
hazard, avoid a hazard and recognize the consequences.
SHOCK HAZA
R
Labels may be located on or inside the equipment (for example, drive or motor) to
alert people that dangerous voltage may be present.
BURN HAZAR
D
Labels may be located on or inside the equipment (for example, drive or motor) to
alert people that surfaces may be dangerous temperatures.
DeviceNet ArmorBlock Network and Auxiliary Powered Module, Series A 3
Publication 1732D-IN011A-EN-E - April 2009
Environment and Enclosure
Prevent Electrostatic Discharge
ATTENTION This equipment is intended for use in overvoltage Category II applications (as
defined in IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating.
This equipment is considered Group 1, Class A industrial equipment according
to IEC/CISPR 11. Without appropriate precautions, there may be difficulties
with electromagnetic compatibility in residential and other environments due
to conducted and radiated disturbances.
This equipment is supplied as enclosed equipment. It should not require
additional system enclosure when used in locations consistent with the
enclosure type ratings stated in the Specifications section of this publication.
Subsequent sections of this publication may contain additional information
regarding specific enclosure type ratings, beyond what this product provides,
that are required to comply with certain product safety certifications.
In addition to this publication, see:
•Industrial Automation Wiring and Grounding Guidelines, Allen-Bradley
publication 1770-4.1, for additional installation requirements.
•NEMA Standards 250 and IEC 60529, as applicable, for explanations of
the degrees of protection provided by different types of enclosure.
ATTENTION This equipment is sensitive to electrostatic discharge, which can cause
internal damage and affect normal operation. Follow these guidelines when
you handle this equipment.
•Touch a grounded object to discharge potential static.
•Wear an approved grounding wriststrap.
•Do not touch connectors or pins on component boards.
•Do not touch circuit components inside the equipment.
•Use a static-safe workstation, if available.
•Store the equipment in appropriate static-safe packaging when not in
use.
4DeviceNet ArmorBlock Network and Auxiliary Powered Module, Series A
Publication 1732D-IN011A-EN-E - April 2009
About the Module
The DeviceNet 1732D ArmorBlock I/O family consists of stand-alone
24V DC I/O modules that communicate via the DeviceNet network. The
sealed IP69K housing of these modules requires no enclosure. Note that it is
possible that environmental requirements other than IP69K require an
additional appropriate enclosure. I/O connectors are sealed M12 style.
The DeviceNet network uses advanced network technology,
producer/consumer communication, to increase network functionality and
throughput. Visit our web site at http://www.ab.com/networks for
producer/consumer technology information and updates.
I - 0
I - 1
I - 2
I - 3
I - 4
I - 5
I - 6
I - 7
O - 0
O - 1
O - 2
O - 3
O - 4
O - 5
O - 6
O - 7
X10 X1
2
4
8
66
00
82
4
P
W
R
DNet In DNet Out
NETMOD
44763
Node address
M18-style auxiliary
power connector
Module status indicator Network status indicator
M12-style
input connector (4)
M12-style DeviceNet
connector
Input status indicator (8)
Auxiliary power status
indicator
M12-style output connector
Output status indicator (8)
DeviceNet ArmorBlock Network and Auxiliary Powered Module, Series A 5
Publication 1732D-IN011A-EN-E - April 2009
Catalog Number Explanation
The catalog number 1732D-8X81212HD identifies a DeviceNet 24V DC
8-port 8-input 8-output 1.4 A M12-style network connector module.
Install the Module
To install the module:
•Set the node address
•Mount the module
•Connect the cord sets
Set the Node Address
Valid node addresses are 00 through 63.
Set the node address using either the rotary switches, RSNetWorx for
DeviceNet, DeviceNetManager, or another software configuration tool.
Setting the switches at any number from 64 through 99 lets the software have
address control.
Each module is shipped set for node address 63. Remove the caps on the
front of the module to access the switches. The two switches are:
•X10 (most significant digit) - left side of module
•X1 (least significant digit) - right side of module
6DeviceNet ArmorBlock Network and Auxiliary Powered Module, Series A
Publication 1732D-IN011A-EN-E - April 2009
To reset the node address:
1. Rotate the switches using a small blade screwdriver.
2. Line up the small black dot on the switch with the number setting you
wish to use.
3. Cycle power.
The rotary switches are read periodically. If the switches have been changed
since the last time they were read and they no longer match the online address,
a minor fault occurs, which is indicated by a flashing red MOD LED.
Settings of 64 through 99 cause the module to use the last valid node address
stored internally. For example, the last setting internally was 40. If a change is
made to 68, and then you power up, the address defaults to 40.
The module is equipped with AutoBaud detect. AutoBaud lets the module
read the settings already in use on your DeviceNet network and automatically
adjusts to those settings.
Mount the Module
Two sets of mounting holes are used to mount the module directly to a panel
or machine. Mounting holes accommodate #6 (M3) pan head screws. The
torque specification is 0.64 Nm (6 in-lb).
Example shows
default node
address set at 63. 43968
DeviceNet ArmorBlock Network and Auxiliary Powered Module, Series A 7
Publication 1732D-IN011A-EN-E - April 2009
Product Dimensions
Refer to the mounting dimensions illustration to help you mount the module.
Module Dimensions
I - 0
I - 1
I - 2
I - 3
I - 4
I - 5
I - 6
I - 7
O - 0
O - 1
O - 2
O - 3
O - 4
O - 5
O - 6
O - 7
X10 X1
2
4
8
66
00
82
4
P
W
R
NETMOD
DNet In DNet Out
65 mm
(2.56 in.) 43.25 mm
(1.70 in.)
179 mm
(7.05 in.)
44799
Front view Side view
26.5 mm
(1.04 in.)
169 mm
(6.64 in.)
8DeviceNet ArmorBlock Network and Auxiliary Powered Module, Series A
Publication 1732D-IN011A-EN-E - April 2009
Mounting the Module in High Vibration Areas
If you mount the module in an area that is subject to shock or vibration,
we recommend that you use a flat and a lock washer to mount the module.
Mount the flat and the lock washer as shown in the mounting illustration.
Torque the mounting screws to 0.64 Nm (6 in-lb).
Connect the I/O Cord Sets to the ArmorBlock Module
The ArmorBlock DeviceNet family has 5-pin M12-style connectors.
We provide caps to cover the unused connectors on your module.
Connect the quick-disconnect cord sets that you selected for your module to
the appropriate ports.
44766
Flat washer
Lock washer
DeviceNet ArmorBlock Network and Auxiliary Powered Module, Series A 9
Publication 1732D-IN011A-EN-E - April 2009
Network Connector
Refer to the pinout diagram for the network connector.
M12-style Input Connectors
I/O Connectors
Refer to the pinout diagrams for the I/O connectors.
M12-style 5-pin Female Input Connectors
M12-style 5-pin Female Output Connector
Male Female
(View into Connector)
Pin 1 Drain
Pin 2 V+ (Red)
Pin 3 V- (Black)
Pin 4 CAN_H (White)
Pin 5 CAN_L (Blue)
4145244175
(View into Connector)
Pin 1 Sensor Source Voltage
Pin 2 Input B
Pin 3 Return
Pin 4 Input A
Pin 5 PE
41452
41452
(View into Connector)
Pin 1 Not Used
Pin 2 Output B
Pin 3 Return
Pin 4 Output A
Pin 5 PE
10 DeviceNet ArmorBlock Network and Auxiliary Powered Module, Series A
Publication 1732D-IN011A-EN-E - April 2009
Auxiliary Power Cable
Refer to the pinout diagram to attach auxiliary power.
M18-style 4-pin Male Auxiliary Power Connector
Refer to publication M116-CA001 for Rockwell Automation cable and cord
set offerings or access the Connection Systems website at
http://www.ab.com/sensors/products/connection_systems/.
ATTENTION If any I/O devices connected to this equipment require Class 2 power to
operate, this equipment and all connected I/O must be powered by a Class 2
source.
To comply with the CE Low Voltage Directive (LVD), this equipment and all
connected I/O must be powered from a source compliant with the following:
Safety Extra Low Voltage (SELV) or Protected Extra Low Voltage (PELV).
ATTENTION Make sure all connectors and caps are securely tightened to properly seal the
connections against leaks and maintain IP enclosure type requirements.
42
1
3
43906
(View into Connector)
Pin 1 Output Power+
Pin 2 No Connection
Pin 3 No Connection
Pin 4 Output Power-
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Rockwell Automation Steuereinheit Handbücher
Rockwell Automation
Rockwell Automation Allen-Bradley PowerFlex 20-750-PNET Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley POINT I/O B Series Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley Guard I/O DeviceNet 1732DS-IB8 Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley ArmorBlock 1732E-IB8M8SOER Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley 1606-XLSBUFFER24 Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley SynchLink 1756-DM Series Leitfaden
Rockwell Automation
Rockwell Automation Allen-Bradley MicroLogix 1762-OW16 Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley 2198-R031 Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley 800G-XLS Z-EX Series Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley 1769-OF4 Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley MSR42 Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley 1746-BTM Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley 1756-EN2TSC Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley FLEX Ex 1797-IRT8 Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley FLEX Integra Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley FLEX 5000 Series Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley 1441-DYN25-MBAL Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley Kinetix 3 Bedienungsanleitung
Rockwell Automation
Rockwell Automation 1794-OB8 Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley 1769-SM2 Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley 1756-EWEB Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen Bradley Guardmaster Sipha 2 Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley ControlLogix 1756-HSC Bedienungsanleitung
Rockwell Automation
Rockwell Automation Allen-Bradley 1718 Series Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
