Rockwell Automation Allen-Bradley Kinetix 3 Bedienungsanleitung

Kinetix 3 Motion Control Indexing Device Building Block

Connected Components Accelerator Toolkit

Quick Start

Important User Information

Read this document and the documents listed in the additional resources section about installation, configuration, and

operation of this equipment before you install, configure, operate, or maintain this product. Users are required to

familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws,

and standards.

Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required

to be carried out by suitably trained personnel in accordance with applicable code of practice.

If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be

impaired.

In no event will Rockwell Automation®, Inc. be responsible or liable for indirect or consequential damages resulting from

the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and

requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or

liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or

software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation,

Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

Labels may also be on or inside the equipment to provide specific precautions.

Allen-Bradley, Connected Components Workbench, Micro800, Micro830, Micro850, PanelView, Kinetix, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment,

which may lead to personal injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property

damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.

IMPORTANT

Identifies information that is critical for successful application and understanding of the product.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous

voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may

reach dangerous temperatures.

ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to

potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL

Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE).

Rockwell Automation Publication CC-QS025D-EN-P - August 2015 3

Where to Start

Follow this path to complete your Connected Components Accelerator Toolkit (CCAT) project.

1- Kinetix 3 Component-class Servo Drive Setup

2- System Validation

Getting Started Connected

Components Accelerator Toolkit with

System Design Assistant Quick Start,

publication CC-QS035

4Rockwell Automation Publication CC-QS025D-EN-P - August 2015

Where to Start

Notes:

Rockwell Automation Publication CC-QS025D-EN-P - August 2015 5

Table of Contents

Preface

About This Publication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Terminology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Available Connected Components Accelerator Toolkits . . . . . . . . . . . . . . 9

Chapter 1

Kinetix 3 Component-class Servo

Drive Setup

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

What You Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Follow These Steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Configure the Kinetix 3 Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Configure Your Kinetix 3 Drive and Personal Computer

Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Connect to Your Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Configure Your Drive by Using Connected Components

Workbench Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Configure the Drive for Modbus Communication Protocol . . . . . . . . . 26

Chapter 2

System Validation

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

What You Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Follow These Steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Review the System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Configure the Controller Serial Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Configure PanelView 800 Terminal Communication Settings . . . . . . . 34

Connect Your Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Download Your Program to the Controller . . . . . . . . . . . . . . . . . . . . . . . . 37

Configure the IP Address for Your PanelView 800 Terminal . . . . . . . . 39

Transfer Your HMI Application to the PanelView 800 Terminal . . . . 39

Validate Your System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Understand the Machine Functions Screen . . . . . . . . . . . . . . . . . . . . . 41

Understand the Device Overview Screen . . . . . . . . . . . . . . . . . . . . . . . 42

Understand the Status and Command Screen. . . . . . . . . . . . . . . . . . . 43

Understand the Index Values Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Verify the Manual Operation of the Drive . . . . . . . . . . . . . . . . . . . . . . 46

Appendix A

Kinetix 3 Component-class User-

defined Functional Block

RA_K3_MBUS_STS User-defined Function Block. . . . . . . . . . . . . . . . . 49

RA_K3_MBUS_STS_Extended User-defined Function Block . . . . . . 52

RA_K3_MBUS_CMD_Indexing User-defined Function Block . . . . . 54

RA_K3_MBUS_CMD_Jog User-defined Function Block . . . . . . . . . . 56

RA_K3_MBUS_CFG_IndexWriteValues User-defined

Function Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

6Rockwell Automation Publication CC-QS025D-EN-P - August 2015

Table of Contents

RA_K3_MBUS_CFG_IndexReadValues User-defined

Function Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Appendix B

Configure Your Personal Computer

and Series A Kinetix 3 Drive

Connection with Ultraware Software

Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

What You Need. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Follow These Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Verify Drive Communication Configuration . . . . . . . . . . . . . . . . . . . . . . . 67

Connect Your Kinetix 3 Drive to a Personal Computer by

Using Ultraware Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Review the Workspace and Drive Branches . . . . . . . . . . . . . . . . . . . . . . . . . 70

Mode Configuration Branch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Reset the Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Configure Basic Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Configure Advanced Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Rockwell Automation Publication CC-QS025D-EN-P - August 2015 7

Preface

About This Publication

This quick start is designed to provide instructions for implementing a Kinetix® 3 component-class drive motion control

indexing application by using Connected Components Workbench™ software and a Micro800® programmable logic

controller (PLC).

To help with the design and installation of your system, application files and other information are provided by the

Connected Components Accelerator Toolkit (CCAT). The CCAT provides bills of materials (BOM), CAD drawings for

panel layout and wiring, control programs, human machine interface (HMI) screens, and more. With these tools and the

built-in best-practices design, the system designer is free to focus on the design of their machine control and not on design

overhead tasks.

The CCAT is available on the Connected Components Accelerator Toolkit DVD, publication CC-QR002, or through

the Rockwell Software® Download and Registration System (SDRS) at http://www.rockwellautomation.com/

rockwellautomation/products-technologies/connected-components/tools/accelerator-toolkit.page.

The beginning of each chapter contains the following information. Read these sections carefully before you begin work in

each chapter:

• Before You Begin - The chapters in this quick start do not have to be completed in the order in which they appear.

However, this section defines the minimum amount of preparation that is required before completing the current

chapter.

• What You Need - This section lists the tools that are required to complete the steps in the current chapter, including,

but not limited to, hardware and software.

• Follow These Steps - This section illustrates the steps in the current chapter and identifies the steps that are required

to complete the examples.

8Rockwell Automation Publication CC-QS025D-EN-P - August 2015

Preface

Terminology

Term (abbreviation) Definition

Application Sequence Programs User-modified programs that work together with the standard state machine logic to

control what the machine does while in the abort, clear, reset, run, and stop states.

Auto/manual operation When the PanelView™ 800 terminal is in Auto mode, the controller logic controls the

machine and monitors machine status.

When the PanelView 800 terminal switches to Manual mode, the terminal takes over

control. Command buttons and numeric entry fields are available only when the machine

is in Manual mode.

Bill of Materials (BOM) A list of components that are needed for your system.

Building block (BB) Tools for accelerating and simplifying the development of a Micro800 controller-based

application. A typical building block includes a starting Bill of Material (BOM), Computer-

Aided Design (CAD) drawings, Micro800 controller programs, PanelView 800 terminal

applications, and a quick start document.

CCAT project A project that consists of these items:

• ProposalWorks™ - based bill of materials

• Set of CAD drawings (dimensions and schematics)

• Connected Components Workbench project

• HMI screens

• Set of Quick Start documents

• Project document with information about the project components and links to

reference materials

Computer-Aided Design (CAD) A computer-based system that is developed to facilitate design of mechanical parts.

Connected Components Accelerator Toolkit (CCAT) Software with application files and other information to speed the design and startup of

component-based machines.

Connected Components Workbench Software environment for configuring or programming Micro800 controllers, PanelView

800 terminals, Kinetix 3 drives, and other component-level products.

Connected Components Workbench project A project consists of one or more of the following:

• Micro800 controller configuration

• Up to 256 Micro800 controller programs, each with program local variables

• Micro800 controller global variables

• PanelView 800 terminal application

• Kinetix 3 drive parameter lists

Global variables Project variables that any program can access, including all I/O and system variables.

State Machine control code Machine logic for coordinating overall machine operation that is based on states. The

state machine broadcasts commands and receives feedback information from each of the

building blocks via user-modified application sequence programs.

Tags A PanelView 800 terminal term for variables.

User-defined Function Blocks (UDFBs) Function block instructions that can be used like standard function block instructions

within any Connected Components Workbench programming language. Anyone using

Connected Components Workbench software can write these functions blocks. Many

UDFBs are posted on the Rockwell Automation sample code website: http://

samplecode.rockwellautomation.com/idc/groups/public/documents/webassets/

sc_home_page.hcst.

User-defined Object (UDO) A collection of PanelView 800 terminal screen objects that can be pasted into a new

screen.

Rockwell Automation Publication CC-QS025D-EN-P - August 2015 9

Preface

Additional Resources

These resources contain information about related products from Rockwell Automation.

You can view or download publications at http://www.rockwellautomation.com/literature. To order paper copies of

technical documentation, contact your local Allen-Bradley distributor or Rockwell Automation sales representative.

Available Connected Components Accelerator Toolkits

For the most up-to-date listing of available Connected Components Accelerator Toolkits and related quick starts, refer to

these resources:

• Rockwell Automation Connected Components Accelerator Toolkit website at http://

www.rockwellautomation.com/rockwellautomation/products-technologies/connected-components/tools/

accelerator-toolkit.page.

• Connected Components Accelerator Toolkit Building Block Project Descriptions Quick Reference, publication

CC-QR003.

Resource Description

Connected Components Accelerator Toolkit DVD, publication

CC-QR002

Provides files for the Connected Component Accelerator Toolkits.

Micro800 and Connected Components Workbench Getting

Started Guide, publication 2080-QR001

Provides information on basic Micro800 controller and Connected Components Workbench software functions.

Micro800 and Connected Components Workbench Application

Guide, publication 2080-QR002

Provides procedures for completing basic tasks in Connected Components Workbench software and for using

Connected Components Workbench software with component-class products.

Micro800 Programmable Controller External AC Power Supply

Installation Instructions, publication 2080-IN001

Provides information on mounting and wiring the optional external power supply.

Micro820 Programmable Controllers User Manual,

publication 2080-UM005

Provides information on installing the Micro820™ Programmable Controller including wiring and

troubleshooting.

Micro830 and Micro850 Programmable Controllers User Manual,

publication 2080-UM002

Provides information on installing the Micro830® and Micro850® Programmable Controllers including wiring and

troubleshooting.

PanelView 800 HMI Terminals Installation Instructions,

publication 2711R-IN001

Provides information on installing the PanelView 800 HMI terminals including wiring, grounding, and

troubleshooting.

PanelView 800 HMI Terminals User Manual, publication

2711R-UM001

Provides information about using PanelView 800 HMI terminals.

Kinetix 3 Component Servo Drives User Manual, publication

2071-UM001

Provides a reference guide for Kinetix 3 drive systems, and accessories. It also contains procedures on how to

install, wire, and troubleshoot your drive.

Kinetix 3 Host Commands for Serial Communication Reference

Manual, publication 2071-RM001

Provides information on the serial communication commands, both ASCII and ModBus-RTU, for interfacing a

motion controller with the Kinetix 3 drive.

Kinetix 3 Component Servo Drives Installation Instruction,

publication 2071-IN001

Provides information on installing your Kinetix 3 drive system.

10 Rockwell Automation Publication CC-QS025D-EN-P - August 2015

Preface

Notes:

Inhaltsverzeichnis

Andere Rockwell Automation Steuereinheit Handbücher

Rockwell Automation

Rockwell Automation D2-3563 Bedienungsanleitung

Rockwell Automation

Rockwell Automation ControlLogix 1756-HYD02 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1606-XLERED Bedienungsanleitung

Rockwell Automation

Rockwell Automation Micro800 Series Handbuch

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-SM2 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 2711P-RPA Bedienungsanleitung

Rockwell Automation

Rockwell Automation ControlLogix 1756-M02AE Gebrauchsanweisung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 750 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 2198-R031 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Reliance Electric LiquiFlo 41L4060 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-OF4 Bedienungsanleitung

Rockwell Automation

Rockwell Automation AB quality Allen-Bradley 1746-INT4 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley SynchLink 1756-SYNCH Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlNet 1734-ACNR Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FLEX Integra Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1756-HIST1G Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-IB16ISOE Bedienungsanleitung

Rockwell Automation

Rockwell Automation Bulletin 193 E1 PLUS Benutzerhandbuch

Rockwell Automation

Rockwell Automation ArmorBlock MaXum 1792D-8BT8PE Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FLEX 5000 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley SynchLink 1751-SLBA Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1794-OB8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation ControlLogix 1756-EN2TR Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted TMR Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung