Rockwell Automation MD60 Bedienungsanleitung

Instruction Manual

MD60 AC Drive

User Manual

Version 3.0

D2-3499-3

The information in this manual is subject to change without notice.

Throughout this manual, the following notes are used to alert you to safety

considerations:

Important: Identifies information that is critical for successful application and

understanding of the product.

ATTENTION:Identifies information about practices or

circumstances that can lead to personal injury or death,

property damage, or economic loss.

MD60, VS Utilities, and Reliance are trademarks of Rockwell Automation.

ATTENTION: Only qualified personnel familiar with the

construction and operation of this equipment and the hazards

involved shouldinstall,adjust,operate,orservicethisequipment.

Read and understand this document in its entirety before

proceeding. Failure to observe this precaution could result in

severe bodily injury or loss of life.

ATTENTION: Thedrivecontainshighvoltagecapacitorsthattake

time to discharge after removal of mains supply. Before working

on the drive, ensure isolation ofmains supply from line inputs [R,

S, T (L1, L2, L3)]. Wait three (3) minutes for capacitors to

dischargeto safevoltage levels.DarkeneddisplayLEDs isnot an

indication that capacitors have discharged to safe voltage levels.

Failure to observe this precaution could result in severe bodily

injury or loss of life.

ATTENTION: Thedrivecanoperateatandmaintainzerospeed.

The user is responsible for assuring safe conditions for operating

personnel by providing suitable guards, audible or visual alarms,

or other devices to indicate that the drive is operating, or may

operate, at or near zero speed. Failure to observe this precaution

could result in severe bodily injury or loss of life.

ATTENTION: The drive contains ESD- (Electrostatic Discharge)

sensitive parts and assemblies. Static control precautions are

required when installing, testing, servicing, or repairing the drive.

Erratic machine operation and damage to, or destruction of,

equipment can result if this procedure is not followed. Failure to

observe this precaution can result in bodily injury.

ATTENTION: The user must provide an external, hardwired

emergency stop circuit outside of the drive circuitry. This circuitry

must disable the system in case of improper operation.

Uncontrolledmachineoperationmayresultifthisprocedureisnot

followed. Failure to observe this precaution could result in bodily

injury.

ATTENTION: The user is responsible for conforming with all

applicable local and national codes. Failure to observe this

precaution could result in damage to, or destruction of, the

equipment.

ATTENTION: An incorrectly applied or installed drive can result

in component damage or reduction in product life. Wiring or

application errors, such as undersizing the motor, incorrect or

inadequate AC supply, or excessive ambient temperatures may

result in malfunction of the system.

Contents I

CONTENTS

Chapter 1 Introduction

1.1 Getting Assistance from Reliance Electric..................... 1-1

Chapter 2 About the MD60 Drive

2.1 Identifying the Drive by Model Number.......................... 2-1

2.2 MD60 Drive Ratings, Model Numbers, and Frame

Sizes ............................................................................. 2-2

2.3 Kits................................................................................. 2-3

2.4 Storage Guidelines........................................................ 2-4

Chapter 3 Mounting the Drive

3.1 General Requirements for the Installation Site.............. 3-1

3.1.1 Operating Conditions........................................... 3-2

3.1.2 Recommended Mounting Clearances................. 3-2

3.1.3 Mounting Dimensions for the MD60 Drive........... 3-3

3.2 Mounting the Drive......................................................... 3-4

3.2.1 Protecting the Drive from Debris ......................... 3-4

Chapter 4 Grounding the Drive

4.1 RFI Filter Grounding...................................................... 4-2

Chapter 5 Installing Power Wiring

5.1 Opening the Cover......................................................... 5-1

5.2 Verifying Drive AC Input Ratings Match Available

Power........................................................................... 5-2

5.2.1 Ungrounded Distribution Systems....................... 5-2

5.2.2 Input Power Conditioning .................................... 5-4

5.3 Power Wiring Specifications.......................................... 5-5

5.4 Power Terminal Block Connections............................... 5-5

5.5 Fuses and Circuit Breakers ........................................... 5-6

5.6 Motor Cable Types Acceptable for 200-600 Volt

Installations ................................................................... 5-8

5.7 Reflected Wave Protection............................................ 5-9

5.8 Output Disconnect....................................................... 5-10

Chapter 6 Installing Control Wiring

6.1 Stop Circuit Requirements............................................. 6-1

6.1.1 Compliance with Machinery Safety Standard EN

60204-1:1992...................................................... 6-2

6.2 Motor Start/Stop Precautions......................................... 6-2

6.3 I/O Wiring Recommendations........................................ 6-3

6.3.1 Maximum Cable Length Recommendations........ 6-3

6.4 Wiring the Control Terminal Block................................. 6-4

6.4.1 I/O Wiring Examples............................................ 6-5

II MD60 AC Drive User Manual

6.4.2 Typical Multiple Drive Connection Examples....... 6-7

6.5 Start and Speed Reference Control...............................6-8

6.6 Accel/Decel Selection....................................................6-9

Chapter 7 Completing the Installation

7.1 Checking the Installation Before Applying Power to the

Drive .............................................................................. 7-1

7.2 Powering Up After Installation is Complete....................7-2

Chapter 8 Using the Integral Keypad to Program and Control the Drive

8.1 Keypad Components .....................................................8-1

8.1.1 Display Description..............................................8-2

8.1.2 LED Descriptions.................................................8-2

8.1.3 Key Descriptions..................................................8-3

8.2 About Parameters..........................................................8-4

8.3 How Parameters are Organized ....................................8-4

8.4 Viewing and Adjusting Basic (P) and Advanced (A)

Parameters....................................................................8-5

8.5 Viewing the Display (d) Parameters...............................8-6

Chapter 9 Parameter Descriptions

9.1 Basic Program Group Parameters.................................9-2

9.2 Advanced Group Parameters ........................................9-8

9.3 Display Group Parameters...........................................9-27

Chapter 10 Troubleshooting the Drive

10.1Fault Codes..................................................................10-1

10.1.1Manually Clearing Faults...................................10-2

10.1.2Automatically Clearing Faults (Auto Restart

Feature)............................................................10-2

10.2Troubleshooting Tables ................................................10-6

10.2.1Problem: Drive Does Not Start From Terminal Block

Start or Run Inputs ............................................10-6

10.2.2Problem: Drive Does Not Start From Integral

Keypad.............................................................10-7

10.2.3Problem: Drive Does Not Respond to Changes in

Speed Command ..............................................10-7

10.2.4Problem: Motor and/or Drive Will Not Accelerate to

Commanded Speed ..........................................10-8

10.2.5Problem: Motor Operation is Unstable...............10-8

10.2.6Problem: Drive Will Not Reverse Motor

Direction...........................................................10-9

Appendix A Technical Specifications................................................... A-1

Appendix B Record of User Settings ................................................... B-1

Appendix C Parameters Cross-Referenced by Name ......................... C-1

Contents III

Appendix D CE Conformance Requirements .......................................D-1

Appendix E Accessories.......................................................................E-1

Appendix F RS485 (MDI) Protocol........................................................F-1

Appendix G RJ45 Splitter Cable..........................................................G-1

Index ...................................................................................... Index-1

IV MD60 AC Drive User Manual

Contents V

List of Figures

Figure 2.1 – Identifying the Drive by Model Number..................................2-1

Figure 3.1 – Minimum Mounting Clearances.............................................3-2

Figure 3.2 – Drive Dimensions - Front View..............................................3-3

Figure 3.3 – Drive Dimensions - Bottom View...........................................3-3

Figure 4.1 – Typical Grounding..................................................................4-1

Figure 5.1 – Opening the Cover.................................................................5-1

Figure 5.2 – Removing the Finger Guard..................................................5-2

Figure 5.3 – Jumper Location (A Frame Shown).......................................5-3

Figure 5.4 – Phase-to-Ground MOV Removal...........................................5-3

Figure 5.5 – Power Terminal Block Connections....................................... 5-5

Figure 6.1 – Wiring the Control Terminal Block.........................................6-4

Figure 6.2 – I/O Wiring Examples..............................................................6-5

Figure 6.3 – Override Priority for the Speed Reference Command........... 6-8

Figure 6.4 – Accel/Decel Selection............................................................6-9

Figure 8.1 – Integral Keypad .....................................................................8-1

Figure 9.1 – Accel Time 1 (P039)..............................................................9-7

Figure 9.2 – Decel Time 1 (P040)..............................................................9-7

Figure 9.3 – Accel Time 2 (A067)............................................................9-11

Figure 9.4 – Decel Time 2 (A068)............................................................9-12

Figure 9.5 – DC Brake Level (A081)........................................................9-14

Figure 9.6 – S Curve% (A083) Examples................................................9-15

Figure 9.7 – Start Boost (A084)...............................................................9-16

Figure 9.8 – Motor OL Select (A090).......................................................9-17

Figure 9.9 – Derating Guidelines Based on PWM Frequency (A091)

Selection...........................................................................9-18

Figure 9.10 – Drive Status (d006) Bit Definitions.....................................9-28

Figure 9.11 – Control Source (d012) Bit Definitions ................................9-29

Figure 9.12 – Control Input Status (d013) Bit Definitions.........................9-30

Figure 9.13 – Digital Input Status (d014) Bit Definitions..........................9-30

Figure 9.14 – Comm Status (d015) Bit Definitions...................................9-31

VI MD60 AC Drive User Manual

Contents VII

List of Tables

Table 2.1 – Drive Ratings, Model Numbers, and Frame Sizes..................2-2

Table 2.2 – Standard Kits..........................................................................2-3

Table 3.1 – Ambient Operating Temperatures and Mounting Clearances.3-2

Table 3.2 – Mounting Specifications..........................................................3-4

Table 5.1 – Corrective Actions for Input Power Conditions.......................5-4

Table 5.2 – Power Wiring Specifications ...................................................5-5

Table 5.3 – Power Terminal Block Specifications......................................5-5

Table 5.4 – Drive, Fuse, and Circuit Breaker Ratings................................5-7

Table 5.5 – Shielded Motor Cable Types Acceptable for 200-600 Volt

Installations..........................................................................5-8

Table 5.6 – Maximum Cable Length Recommendation.............................5-9

Table 6.1 – Recommended Control and Signal Wire.................................6-3

Table 6.2 – I/O Terminal Block Specifications...........................................6-3

Table 6.3 – Typical Multiple Drive Connection Examples..........................6-7

Table 8.1 – LED Descriptions....................................................................8-2

Table 8.2 – Key Descriptions.....................................................................8-3

Table 8.3 – Viewing and Adjusting Basic (P) and Advanced (A)

Parameters ..........................................................................8-5

Table 8.4 – Viewing the Display (d) Parameters........................................8-6

Table 9.1 – Trip Points for Digital Output Relay.......................................9-11

Table 9.2 – Selecting the Reference Source Using Presets....................9-13

Table 10.1 – Fault Descriptions and Corrective Actions..........................10-3

Table 10.2 – Problem: Drive Does Not Start From Terminal Block Start

or Run Inputs ...................................................................10-6

Table 10.3 – Problem: Drive Does Not Start From Integral Keypad........10-7

Table 10.4 – Problem: Drive Does Not Respond to Changes in Speed

Command .........................................................................10-7

Table 10.5 – Problem: Motor and/or Drive Will Not Accelerate to

Commanded Speed..........................................................10-8

Table 10.6 – Problem: Motor Operation is Unstable................................10-8

Table 10.7 – Problem: Drive Will Not Reverse Motor Direction...............10-9

VIII MD60 AC Drive User Manual

Andere Handbücher für MD60

Inhaltsverzeichnis

Andere Rockwell Automation Gleichstromantrieb Handbücher

Rockwell Automation

Rockwell Automation RELIANCE ELECTRIC SP120 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 7000 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 755 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley DriveGuard B Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Reliance electric 6SB401 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation 14C214 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Reliance electric GV3000/SE Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 160-AA02 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley IMPACT 1336 Series Programmierhandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 7000 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 400P Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 40 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 700 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley DRIVES HEADQUARTERS Flying Start PowerFlex... Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 700 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 4 FKN6 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 755T Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix 5700 Series Benutzerhandbuch

Rockwell Automation

Rockwell Automation PowerFlex 7000 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Reliance electric FlexPak 3000 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 6000 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex series Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700H Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung

Beckhoff

Beckhoff AX8911 Bedienerhandbuch

Lenze

Lenze 8200 vector Bedienungsanleitung

Danfoss

Danfoss VLT DriveMotor FCP 106 Leitfaden