Rockwell Automation Reliance electric FlexPak 3000 Bedienungsanleitung

Instruction Manual

Pulse Encoder Interface Kit

For Use With FlexPak™3000

and WebPak™3000 DC Drives

M/N 907FK0101

D2-3302-3

The information in this manual is subject to change without notice.

Throughout this manual, the following notes are used to alert you to safety considerations:

Important: Identifies information that is critical for successful application and understanding of the product.

The thick black bar shown on the outside margin of this page will be used throughout this instruction manual to

signify new or revised text or figures.

!ATTENTION:Identifies information about practices or circumstances that can lead to personal

injury or death, property damage, or economic loss.

FlexPak, WebPak, and Reliance are trademarks of Rockwell Automation.

!ATTENTION:Only qualified electrical personnel familiar with the construction and operation of

thisequipmentandthehazardsinvolvedshouldinstall,adjust,operate,orservicethisequipment.

Read and understand this manual and other applicable manuals in their entirety before

proceeding. Failure to observe this precaution could result in severe bodily injury or loss of life.

ATTENTION:Donotinstallorremovemodificationkitswithpowerappliedtothedrive.Disconnect

and lock out incoming power before attempting such installation or removal. Failure to observe

this precaution could result in severe bodily injury or loss of life.

ATTENTION:The user is responsible for conforming with all applicable local, national, and

international codes. Failure to observe this precaution could result in damage to, or destruction

of, the equipment.

Trademarks not belonging to Rockwell Automation are property of their

respective companies.

Contents

CONTENTS

Chapter 1 Introduction

1.1 Related Publications........................................................................................1-1

1.2 Getting Assistance from Reliance Electric.......................................................1-1

Chapter 2 Installing the Pulse Encoder Interface Kit

2.1 Opening the Drive and Carrier.........................................................................2-1

2.2 Mounting the Pulse Encoder Interface Board..................................................2-2

2.3 Wiring the Pulse Encoder Interface Board ......................................................2-4

2.4 Checking Motor and Drive Wiring....................................................................2-5

2.5 Closing the Carrier and Drive ..........................................................................2-5

2.6 Verifying and Adjusting Drive Parameters.......................................................2-6

Chapter 3 Adjusting Drive Parameters

3.1 Adjusting FlexPak 3000 Parameters ...............................................................3-1

3.1.1 Parameter 200 (FEEDBACK SELECT).................................................3-1

3.1.2 Parameter 207 (PULSE TACH PPR)....................................................3-2

3.1.3 Parameter 208 (PULSE TACH QUADRATURE) ..................................3-2

3.1.4 Parameter 798 (PULSE TACH KIT)......................................................3-3

3.2 Adjusting WebPak 3000 Parameters...............................................................3-3

3.2.1 Parameter 200 (FEEDBACK SELECT).................................................3-4

3.2.2 Parameter 207 (ENCODER PPR).........................................................3-4

3.2.3 Parameter 798 (ENCODER KIT)...........................................................3-4

Chapter 4 Determining Pulse Encoder Feedback Polarity...................................................4-1

Appendix A Technical Specifications and Application Data...................................................A-1

Pulse Encoder Interface Kit

Contents

III

List of Figures

Figure 2.1 – Removing the OIM Carrier Shield.........................................................2-1

Figure 2.2 – Installing the Mounting Screws and Washers on the Pulse Encoder

Interface Board.....................................................................................2-2

Figure 2.3 – Mounting the Pulse Encoder Interface Board on the Carrier................2-3

Figure 2.4 – Mounting the Pulse Encoder Interface Board on an I/O Expansion

Board....................................................................................................2-3

Figure 2.5 – Wiring the Pulse Encoder Interface Board ...........................................2-5

Pulse Encoder Interface Kit

Contents

List of Tables

Table 1.1 – Pulse Encoder Interface Kit Contents....................................................1-1

Table 2.1 – Twisted Pair Lead Numbering ...............................................................2-4

Table 3.1 – Pulse Encoder Parameter Ranges for Different Firmware Versions .....3-2

Table 3.2 – Parameter 798 Status Descriptions.......................................................3-3

Table 3.3 – Parameter 798 Status Descriptions.......................................................3-3

Pulse Encoder Interface Kit

Introduction

1-1

CHAPTER 1

Introduction

This instruction manual describes how to install and configure the optional Pulse

Encoder Interface kit used by FlexPak3000 and WebPak3000 Digital DC Drives.

These instructions assume that either a single-channel or quadrature differential

output Pulse Encoder has been properly installed on the drive’s motor. (Follow all

procedures from the manufacturer to properly install the Pulse Encoder on the motor.)

Each M/N 907FK0101 Pulse Encoder Interface kit includes a Pulse Encoder Interface

board (with captive screws), nylon washers, and an extension ribbon cable. See table

1.1.

1.1 Related Publications

This manual describes the Pulse Encoder Interface kit and its associated software

parameters. You will also need the following instruction manuals, which describe the

drive hardware and software.

•D2-3404 FlexPak 3000 Hardware Reference

•D2-3405-1 FlexPak 3000 Software Reference

•D2-3443 WebPak 3000 Hardware Reference

•D2-3444 WebPak 3000 Software Reference

1.2 Getting Assistance from Reliance Electric

If you have any questions or problems with the products described in this instruction

manual, contact your local Reliance Electric sales office. For technical assistance, call

1-800-726-8112.

Table 1.1 – Pulse Encoder Interface Kit Contents

Description Qty Reliance Part Number

M3 x 10 Screw 4 419062-1PEG

Nylon Washer 4 419064-4E

Pulse Encoder Interface Board 1 O-58775

60-pin Ribbon Cable 1 610273-38S

1-2

Pulse Encloder Interface Kit

Andere Handbücher für Reliance electric FlexPak 3000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation Gleichstromantrieb Handbücher

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 7000 Bedienungsanleitung

Rockwell Automation

Rockwell Automation CNMD180W0ENNNC1 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 700 B Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation 14C214 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 755TS Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 700 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Ultra5000 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700 Gebrauchsanweisung

Rockwell Automation

Rockwell Automation Allen-Bradley DriveGuard B Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 520 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted TMR 24V DC Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 753 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 7000 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700H Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 755 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 4M Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix 5700 Series Benutzerhandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley 160 SSC Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Reliance Electric SP200 Bedienungsanleitung

Rockwell Automation

Rockwell Automation RELIANCE ELECTRIC SP120 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Reliance electric GV3000/SE Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung

Beckhoff

Beckhoff AX8911 Bedienerhandbuch

Lenze

Lenze 8200 vector Bedienungsanleitung

Danfoss

Danfoss VLT DriveMotor FCP 106 Leitfaden