Rosewill RC-209 Bedienungsanleitung

SATA 4 Port PCI Adaptor with RAID RC209

User Manual

Content

• Feature highlights ..............................................................................

• Package contents ..............................................................................

• System requirement ..........................................................................

• Magic Switch introduction and jumper setting ...............................

• Step by step photo installation of Magic Switch ............................

• Hardware installation .........................................................................

• Important message for user ..............................................................

• RAID introduction

• RAID 0 ....................................................................................

• RAID 1 ....................................................................................

• RAID 0+1 ................................................................................

• RAID 5 (optional) .....................................................................

• BIOS conﬁguration .............................................................................

• Driver installation

• Quick guide .............................................................................

•Detail guide .............................................................................

User Manual

SATA 4 Port PCI Adaptor with RAID RC209

User Manual

SATA 4 Port PCI Adaptor with RAID RC209

SiI 3114 SATA PCI Card

Feature Highlights

• Silicon Image SiI3114 SATA controller chip

• Compliant with PCI Speciﬁcation, Rev. 2.3, 32bit, 33/66Mhz

• Compliant with Serial ATA 1.0 speciﬁcation

• Provides four independent channels to support up to four Serial ATA drives

• Supports RAID0(striping), RAID1(mirroring), RAID5(Parity RAID), RAID 0+1

(mirroring+striping) and Concatenation modes

• HDD functions normally when not in RAID sets (un-RAID mode)

• Supports SATA up to 150MB/Sec

• Supports Windows® 98SE, Me, 2000, XP/2003 32/64 bit

• Connectors : 4 x internal SATA connectors, 2 x external SATA connectors

Package Contents

• 1x Serial ATA 4-Channel RAID PCI HD controller

• 1x Driver CD

• 2x SATA Data Cables & 2 x SATA Power Cables

• 1x Manual

• 1x Low proﬁle bracket

System Requirements

• Pentium-class computer with one available PCI slot

• Windows® 98SE, ME, 2000, XP/2003 32/64 bit

User Manual

SATA 4 Port PCI Adaptor with RAID RC209

Magic Switch introduction and jumper setting

Before installing the SiI 3114 SATA PCI Card, please see the photo below which shows all the

ports & jumpers on this PCI Card.

A SATA Connector 1 (internal)

B SATA Connector 2 (internal)

C SATA Connector 3 (internal)

D SATA Connector 4 (internal)

E SATA Connector 5 (external)

F SATA Connector 6 (external)

G Jumpers

IDE/RAID: Jumper Settings ( Default mode as below : 2-3 close )

Jumper Settings

JP Description Active port

J1-J4 1-2 close Enable SATA Connector 5

2-3 close Enable SATA Connector 4

J5-J8 1-2 close Enable SATA Connector 6

2-3 close Enable SATA Connector 3

J1 J2 J3 J4 J5 J6 J7 J8

User Manual

SATA 4 Port PCI Adaptor with RAID RC209

Step by step photo installation of Magic Switch

1. There are six SATA ports in RC209 RAID adapter. We named these ports

character A through F. Ports A to D are internal SATA ports and E to F are

external SATA ports. By changing the jumper setting on RC209 that allows you

to utilize 4 ports of this card. Please reference our photos below for the proper

jumper setting. Port A and B are always active. With different jumper setting you

can active port C, D, E and F by referencing the following photos.

2. Available port setting 3. Active Inactive

*Jumper setting for 1 pin and 2 pin close

– connect pin 1 and 2 on J1, J2, J3 and J4.

*Jumper setting for 2 pin and 3 pin close

– connect pin 2 and 3 on J5, J6, J7 and J8.

ABCD

3 PIN

2 PIN

1 PIN

for exsample:

1 & 2 PIN close 2 & 3 PIN close

A,B always active

Control D,E switch

Control C,F switch

ABCD

User Manual

SATA 4 Port PCI Adaptor with RAID RC209

Mode 1 (Default) - ABCD Active

Mode 2 - ABDF Active

Mode 3 - ABEF Active

Active

2.3 close 1.2 close

Active

1.2 close 1.2 close

Active

2.3 close 2.3 close

Active

User Manual

SATA 4 Port PCI Adaptor with RAID RC209

Mode 4 - ABCE Active

Note: There are six SATA ports in Serial ATA 4-Channel RAID adapter. We named these ports

character A through F. Ports A to D are internal SATA ports and E & F are external SATA ports. By

changing the jumper setting on the Serial ATA 4-Channel RAID adapter that allows you to utilize 4

ports of this card at the same time. Please set which port to work by jumper setting. By default,

Port A, B, C and D are working.

Hardware Installation

1. Turn Off the power to your computer and any other connected peripheral devices.

2. Unplug the power cord form the back of the computer.

3. Remove your computer’s cover.

4. Remove the slot bracket from an available PCI slot.

5. To install the card, carefully align the card’s bus connector with the selected PCI slot on

the motherboard. Push the board down ﬁrmly, but gently, until it is well seated.

6. Replace the slot bracket’s holding screw to secure the card.

Device Connection

The Serial ATA 4-Channel RAID adapter is a four channel Serial ATA controller that supports up

to four Serial ATA hard disk drives. It is recommended to use identical hard drives for all RAID

conﬁgurations.

1. Install your hard disk drive(s) in chassis.

2. Connect the Serial ATA hard disk drive to the system power supply using the included Serial

ATA power cable.

Active

1.2 close 2.3 close

Active

User Manual

SATA 4 Port PCI Adaptor with RAID RC209

3. Connect one end of the Serial ATA cable to the hard disk drive.

4. Attach the other end of the Serial ATA cable to the Serial ATA controller on the Serial ATA

4-Channel RAID adapter.

5. Follow the same instructions to connect up to four hard drives. Device connection is now

complete.

6. Replace the computer cover and reconnect the power cord.

Important message for user

1. Backup all your data in HD before setting any RAID.

2. New HD connecting to RC-209 is recommended to “initial” and “format” before setting

a RAID. Otherwise, PC might ﬁnd nothing in the system.

3. Please read the PDF ﬁle of “SATARAID5-UserGuide_v1.40” for basic RAID knowledge.

4. If you want to boot from correct HD either from motherboard HD or RC-209 HD, please

change from BIOS “booting sequence”.

5. Although SATA HD is a “hot swap” design, it is strongly recommended that all users

turn off the power before you add any HD to PC.

6. If you want to use RC-212 as a un-RAID card, please do not enter the RAID BIOS and set

any RAID set at the beginning of booting. You can jump to P11 “Driver installation” directly to

complete the install. The only different is ignoring the step of RAID setting and the driver

setting is the same as a RAID card.

RAID Arrays

RAID Arrays are setup in the Serial ATA 4-Channel RAID adapter’s BIOS.

RAID 0 (Striping)

This RAID array to be used on New/Blank hard drives. Striping will destroy all existing data

on the original hard drive. Auto Conﬁguration is recommended. For applications that require

custom chunk size, Manual Conﬁguration is offered.

User Manual

SATA 4 Port PCI Adaptor with RAID RC209

Auto conﬁguration (recommended)

The default chunk size is 64k when selecting Auto conﬁguration.

1. As the BIOS boots press Ctrl+S or F4 when prompted to enter the RAID BIOS.

2. At the next screen select Create RAID Set, then press Enter.

User Manual

SATA 4 Port PCI Adaptor with RAID RC209

3. Select RAID0, then press Enter.

4. Select the number of drives then press Enter.

5. Select Auto conﬁguration, then press Enter.

6. Input the RAID size, press Enter.

7. When asked Are You Sure (Y/N)?, press Y to accept.

8. Press Ctrl+E to exit the BIOS.

9. When asked Are you sure to exit (Y/N)?, press Yto exit and reboot.

10. Continue with FDISK and FORMAT steps as if you were installing a conventional hard drive.

Manual conﬁguration

1. As the BIOS boots press Ctrl+S or F4 when prompted to enter the RAID BIOS.

2. At the next screen select Create RAID Set, then press Enter.

3. Select RAID0, then press Enter.

4. Select the number of drives then press Enter.

5. Select Manual conﬁguration then press Enter

6. Select chunk size from 8k, 16k, 32k, 64k or 128k, then press Enter.

7. Select the ﬁrst drive, press Enter.

8. Select the second drive, press Enter.

9. If applicable select the 3rd and 4th drives pressing enter after each selection.

10. Input the RAID size, press Enter.

11. When asked Are You Sure(Y/N)?, press Yto accept.

Inhaltsverzeichnis

Andere Rosewill PCI-Karte Handbücher

Rosewill

Rosewill RC304-E Bedienungsanleitung

Rosewill

Rosewill RC-304 Bedienungsanleitung

Rosewill

Rosewill RC-NIC412 Bedienungsanleitung

Rosewill

Rosewill RC210 Bedienungsanleitung

Rosewill

Rosewill RC-510 Bedienungsanleitung

Rosewill

Rosewill RC500 Bedienungsanleitung

Rosewill

Rosewill RC-305E Bedienungsanleitung

Rosewill

Rosewill RC214 Bedienungsanleitung

Rosewill

Rosewill RC-209-EX Bedienungsanleitung

Rosewill

Rosewill RC508 Bedienungsanleitung

Rosewill

Rosewill RNX-N150PCe Bedienungsanleitung

Rosewill

Rosewill RC205 Bedienungsanleitung

Rosewill

Rosewill RC302 Bedienungsanleitung

Rosewill

Rosewill RNX-N300 Bedienungsanleitung

Rosewill

Rosewill RC304 Bedienungsanleitung

Rosewill

Rosewill SATA II 4 Port PCI RAID Card RC217 Bedienungsanleitung

Rosewill

Rosewill RC501 Bedienungsanleitung

Rosewill

Rosewill RC-101 Bedienungsanleitung

Rosewill

Rosewill RC-302 Bedienungsanleitung

Rosewill

Rosewill RNX-N150PCe Bedienungsanleitung

Rosewill

Rosewill RNX-G100 Bedienungsanleitung

Rosewill

Rosewill RNX-N250PC2 Bedienungsanleitung

Rosewill

Rosewill RC-305 Bedienungsanleitung

Rosewill

Rosewill RC-300 Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung