Sper scientific Large Display Salinity Pen - 850036 Bedienungsanleitung

Large Display

Salinity &

Conductivity Pens

850036 & 850037

Large Display

Salinity & Conductivity Pens

850036 & 850037

Sper Scientic

Printed in the USA

The contents of this manual may not be

reproduced or transmitted in any form or

by any means electronic, mechanical, or

other means that do not yet exist or may

be developed, including photocopying,

recording, or any information storage

and retrieval system without the express

permission from Sper Scientic.

Sper Scientic

8281 E. Evans Rd., Suite #103

Scottsdale, AZ 85260

(480) 948-4448

TABLE OF CONTENTS

INTRODUCTION . . . . . . . . . . . . . 4

FEATURES. . . . . . . . . . . . . . . . . 5

MATERIALS SUPPLIED . . . . . . . . . 5

POWER SUPPLY . . . . . . . . . . . . .6

LCD DISPLAY . . . . . . . . . . . . . . . 6

APPENDICES . . . . . . . . . . . . . . 45

BATTERY REPLACEMENT . . . . . . . 52

MAINTENANCE . . . . . . . . . . . . . 53

TROUBLESHOOTING . . . . . . . . . . 54

WARRANTY . . . . . . . . . . . . . . . 56

850036 SALINITY PEN . . . . . . . . . .7

SET UP . . . . . . . . . . . . . . . . . . 8

CALIBRATION . . . . . . . . . . . . . 12

MEASUREMENT PROCEDURES . . . 16

SPECIFICATIONS . . . . . . . . . . . 19

ERROR CODES . . . . . . . . . . . . 20

850037 CONDUCTIVITY PEN . . . . . . 23

SET UP . . . . . . . . . . . . . . . . . 24

CALIBRATION . . . . . . . . . . . . . 32

MEASUREMENT PROCEDURES . . . 38

SPECIFICATIONS . . . . . . . . . . . 42

ERROR CODES . . . . . . . . . . . . 43

INTRODUCTION

The Sper Scientic Large Display Salinity

(Model 850036) and Conductivity (Model

850037) Pens provide highly stable and

accurate readings with a large LCD that

simultaneously displays the parameter

being measured and temperature in

°C or °F. The pens are designed for simple

one-hand operation. The case is IP65

waterproof, and will oat if accidentally

dropped into the water.

Salinity is displayed not as a percentage

but as parts per thousand (ppt), which

is approximately grams of salt per liter

of solution.

Conductivity is displayed as mhos

per centimeter (M/cm) or siemens

per centimeter (S/cm). Because a mho

(or siemen) is a large unit, microsiemen

or millisiemen typically is used (µS/cm,

mS/cm).

FEATURES

• IP65 waterproof housing

• Dual display with ATC

• Data hold

• Pen size for portability

• Built-in probe with protective cap

• One touch, multi-point calibration

• Auto-power-o󰀨

• Low battery indicator

MATERIALS SUPPLIED

• 4 LR44 button cell batteries

• Instruction Manual

POWER SUPPLY

The pen is powered by 4 LR44 batteries.

Check the batteries when:

• Using the unit for the rst time

• The low battery indicator appears

on the LCD

• The pen will not turn on

LCD DISPLAY

-8 -

LCD DISPLAY

Hold data on the LCD

Calibration Mode

Low battery indicator

Unit of conductivity

Measured value

Unit of TDS and

Salinity

Unit of liquid

temperature °C or °F

Temperature reading

Large Display

Salinity Pen

850036

SETUP MODE

The advanced Setup Mode allows you

to customize the pen’s preferences and

defaults:

1. Press SET to turn the pen on.

2. From Measurement Mode, press SET

for more than 2 seconds to enter Setup

Mode and change parameters.

Temperature Units (tUt)

To select the Celsius or Fahrenheit

temperature scale:

1. Press SET for 2 seconds to enter setup.

2. “t” will appear on the primary display of

the LCD and “P1.0” will appear on the

secondary display.

3. Press SET again for less than one

second to enter the unit setting.

4. Press ▲ or ▼ to select C (Celsius) or

F (Fahrenheit). Press SET for less than

one second to conrm the unit selection.

Press SET for more than 2 seconds to

return to P1.0 without saving.

5. When in P1.0, press ▲ to advance to

the next setup function or press SET

for more than 2 seconds to return to

Measurement Mode.

Resetting the Pen (rSt)

When the pen is reset, all parameters

will be reset to factory default values.

1. Press SET for 2 seconds to enter setup.

2. Press ▲ to select the reset pen setting.

“rst” will appear on the main display of

the LCD and “P3.0” will appear on the

secondary display.

3. Press SET again for less than one

second to enter the reset setting.

4. Press ▲ to select Y (yes) or N (no).

-11 -

SETUP MODE

Press and

hold

Press

for less

than 1

second

Press

and

hold

5. Press SET for less than one second to

conrm the selection or press SET for

more than 2 seconds to return to P3.0

without saving.

6. When in P3.0, press ▲ to advance to

the next setup function or press SET

for more than 2 seconds to return to

Measurement Mode.

Calibration Review (CAL)

1. Press SET for 2 seconds to enter setup.

2. Press ▲ to select the calibration review

setting. “CAL” will appear on the primary

display of the LCD and “P4.0” will

appear on the secondary display.

Range 1 Calibration Information:

3. When in P4.0, press SET for less than

one second to enter P4.1 to review the

last calibration concentration. If the pen

is not yet calibrated, “---” will appear on

the LCD.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sper scientific Messgerät Handbücher

Sper scientific

Sper scientific 840003 Bedienungsanleitung

Sper scientific

Sper scientific 840062 Bedienungsanleitung

Sper scientific

Sper scientific 300001 Bedienungsanleitung

Sper scientific

Sper scientific 850070 Bedienungsanleitung

Sper scientific

Sper scientific 850015 Bedienungsanleitung

Sper scientific

Sper scientific 300056 Bedienungsanleitung

Sper scientific

Sper scientific 840046 Bedienungsanleitung

Sper scientific

Sper scientific 840005 Bedienungsanleitung

Sper scientific

Sper scientific CL-2006 Bedienungsanleitung

Sper scientific

Sper scientific 860032 Bedienungsanleitung

Sper scientific

Sper scientific 900019 Bedienungsanleitung

Sper scientific

Sper scientific AquaShock 850034K Bedienungsanleitung

Sper scientific

Sper scientific 300079 Bedienungsanleitung

Sper scientific

Sper scientific 850071 Bedienungsanleitung

Sper scientific

Sper scientific 850023 Bedienungsanleitung

Sper scientific

Sper scientific AquaShock Bluetooth pH Kit 850057K Bedienungsanleitung

Sper scientific

Sper scientific 850068 Bedienungsanleitung

Sper scientific

Sper scientific 840023 Bedienungsanleitung

Sper scientific

Sper scientific 840029 Bedienungsanleitung

Sper scientific

Sper scientific 850020 Bedienungsanleitung

Sper scientific

Sper scientific 800098 Bedienungsanleitung

Sper scientific

Sper scientific 840045 Bedienungsanleitung

Sper scientific

Sper scientific 850001E Bedienungsanleitung

Sper scientific

Sper scientific 840018 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung