Structural Concepts IMPULSE CGC2830 Bedienungsanleitung

REV H DATE: 11/22/2022

Model CGC2830

Dimensions: 28 ”L x 25”D x 30 1/2”H

Model CGC3830

Dimensions: 38 ”L x 25”D x 30 1/2”H

Model CGS2830

Dimensions: 28 ”L x 25”D x 30 1/2”H

Model CGS3830

Dimensions: 38 ”L x 25”D x 30 1/2”H

USER MANUALS/54151_IMPULSE_USER MANUAL_CGC(L)30_CGS(L)30_AMBIENT_SVC_SELF-SVC_CASE

SERVICE / SELF-SERVICE AMBIENT COUNTERTOP DISPLAY MERCHANDISERS

Model CGC2830 in Self-Service

Position and Upward Angled

Shelves

Model CGC2830 in Service

Position and Downward

Angled Shelves

SCC P/N

54151

USER

MANUAL

IMPULSE

CAREFULLY FOLLOW THESE INSTRUCTIONS

Structural Concepts Corp. ∙ 888 E. Porter Rd ∙ Muskegon, MI 49441 Phone: 231.798.8888 Fax: 231.798.4960 ∙ www.structuralconcepts.com

TABLE OF CONTENTS

OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING / PLUGS .....…....…..

START-UP AND OPERATION: CASE PLACEMENT / SERVICE vs. SELF-SERVICE SHELF

SET-UP …………………………………………………………………………………………………...

START-UP AND OPERATION, CONTINUED: BASE SPACER / POWER CORD LENGTH / CORD

CLAMP …………………………………………………………………………………………………...

LED LIGHTING (STANDARD) .………………………………………………….……………………………..

FLUORESCENT LIGHTING (OPTIONAL) …………………………………………………………………...

TROUBLESHOOTING …..…………….………………………………………………………….….…………

SERIAL LABEL LOCATION & INFORMATION LISTED / TECH INFO & SERVICE …………………..

CLEANING SCHEDULE .…………………………………………………...…………………….…………....

TECHNICAL SERVICE CONTACT INFORMATION / WARRANTY INFORMATION ..……..……........

OVERVIEW

• These Structural Concepts cases should be installed and

operated according to these instructions to ensure proper

performance. Improper use will void warranty.

• This unit is designed to display of products in ambient

store conditions with a max. temperature of 80 °F (27 °C) .

COMPLIANCE

• Performance issues when in violation of applicable NEC,

federal, state or local electrical codes are not covered by

warranty. See below.

WARNING

Risk of electric shock.

Disconnect ALL ELECTRICAL SOURCES before servicing.

WARNING

ELECTRICAL

HAZARD

COMPLIANCE

This equipment MUST be installed in compliance with all applicable NEC,

federal, state and local electrical and plumbing codes.

PRECAUTIONS

• Following are important precautions to prevent damage

to unit or merchandise. Read carefully!

WIRING DIAGRAM

• Each case has its own wiring diagram folded and in its

own packet. It may be placed near ballast box, field

wiring box, raceway cover, or other related location.

CAUTION! POWER CORD AND PLUG MAINTENANCE

Risk of electric shock. If cord or plug becomes damaged,

replace only with cord and plug of same type.

CAUTION! GFCI BREAKER USE REQUIREMENT

If N.E.C. (National Electric Code) or your local code

requires GFCI (Ground Fault Circuit Interrupter) protection,

you MUST use a GFCI breaker in lieu of a GFCI receptacle.

OVERVIEW / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING DIAGRAM / CORDS & PLUGS

CAUTION! LAMP REPLACEMENT GUIDELINES

If LED lamps are used, they must be size, shape and overall design.

Any replacements must meet factory specifications.

WARNING: This product can expose you to chemicals, including

Urethane (Ethyl Carbamate), which are known to the state of

California to cause cancer and birth defects or other reproductive

harm. For more information go to P65Warnings.ca.gov.

START-UP AND OPERATION: CASE PLACEMENT / SERVICE VS. SELF-SERVICE SHELF SET-UP

1. Case Placement

• Remove case from skid.

• Before placing case on counter,

determine if the case will merchandize as

a front or rear-mounted case.

• Base spacer has a notch at BOTH front

and rear for power cord to route from

EITHER side.

• See general spacer illustration on next

page.

2. Service Case Shelf Positioning

• Shelves may be positioned in the “down”

position to merchandise as a service

case.

• See illustration at right.

3. Self-Service Shelf Positioning

• The shelves may be positioned in the “up”

position. This will allow the case to be

turned around and merchandise from a

rear mounted position.

• See illustrations below for views of

self-service vs. service display cases.

1 Open Slot

No Open Slots

Service Case

Shelf Position

Move down 2 slots

from top position

Move down 1 slot

from middle position

Tilt up from

bottom slot position

Self-Servicel

Shelf Set-Up

Model

Displayed As

Service Case

Model Displayed As Self-Service Case

START-UP AND OPERATION, CONTINUED: BASE SPACER / POWER CORD LENGTH / CORD CLAMP

• Note: The National Sanitation Foundation (NSF®)

requires the following two steps be done before

this case can be used.

• 1. After case is in position, apply a steady bead of

industrial grade silicone sealant around the base

and counter top. Also, apply silicone sealant to notch

around cord.

• 2. Allow 24 hours for the silicone to dry before using

the case. Plug cord into a certified electrical outlet

with ground.

Route Power Cord

Through Either Front

or Rear Notch

Base Spacer

Note: Illustration may

not reflect every

feature or option of

your particular case.

Cord Clamp

(For Adjusting

Cord Length)

4. Base Spacer / Power Cord Length / Clamp

Locate base spacer in location to put case (cord notch

to be in direction of cord to exit).

• Sit case on spacer carefully routing power cord

through either front or rear notch (as shown below).

• Cord to exit at rear doors side for service cases.

• Cord to exit at front side for self-service cases.

• Power cord can only have a 12” MAXIMUM length

from outer notch to plug (as shown below).

• Adjust cord length with cord clamp attached at

underside of base (as shown below). Tighten

clamp screw securely!

• Remove inside deck pan and fasten base to spac-

er.

LED LIGHTING (STANDARD)

1. LED Style Light Switch

• Light switch is at lower-left-left near LED light.

• See illustration at lower-right.

2. Power Cord and Plug

• Power cord and plug (for LED lights) locations vary

depending upon model.

• Caution! You must plugged in an approved outlet!

3. LED Lights

• LED lights are usually located at both header and

shelving of case; placement on your merchandiser

may differ.

• Check that ALL of the light plugs are properly con-

nected to the LED light.

• Plug must be inserted ALL THE WAY into the LED

light orifice (with no gap) to work properly.

• See TROUBLESHOOTING section in manual if

LED lights malfunction.

4. LED Style Light Fixtures

Removal of faulty LED light:

• LED lights rarely require change-out.

• To remove faulty LED light, simply grasp light near

retaining spring and carefully pull away from its spring.

Disconnect plug from LED’s socket.

• Contact Structural Concepts’ Technical Service

Department for replacement parts (see Technical

Service section of this manual for information).

Replacement of LED light:

• To replace LED light fixture, simply insert new LED light at

proper position (socket must be near plug). Carefully

snap into metal or plastic retainers so LEDs

are held firmly in place.

• Note: LED light and plug must be connected

in a specific manner or they will not work.

• Most plug designs are “barrel type” and merely require

that plug be pushed all the way in.

• See illustrations below and top-right.

LED Light Switch

LED

Lights

LED Light

Plug

LED’s Barrel

Shaped Insert

No Gap

Gap

FLUORESCENT LIGHTING (OPTIONAL)

Lighting

Warning! Disconnect power before providing

maintenance and service to unit.

Caution: Lamps have been treated to resist

breakage and must be replaced with similarly

treated lamps.

• Startup: Turn lights’ “Rocker Switch” on, (switch

location is below doors).

• The lights should illuminate immediately.

However, first time lighting may require a short

warm-up period for the bulbs.

• Slight dimness or flickering of new bulbs is

normal.

Removal of lamp:

• Rotate lamp (1/4-turn) either direction to

disengage (upper or lower) pins/contacts from

lamp-mounting sockets.

• Remove bulb by applying even pressure from

back side at the bulb ends and pulling the

remaining contact from sockets.

Rocker Switch

OFF

Top Light

(behind top cover)

Top Shelf Light

Middle Shelf Light

Installation of lamp:

• Align pins with slot.

• Insert pins into socket by rotating the bulb

1/4-turn to secure either the (upper or lower)

pin contacts into the sockets.

• Rotate remaining bulb contacts (1/4-turn) into

remaining lamp mounting socket contacts.

>> See previous page for LED lighting and

illustrations.

TROUBLESHOOTING

Case Lights Not Working Check bulbs for proper installation and connection.

Check for burned out bulbs.

Clean dirt and dust from the bulbs to prevent flickering.

System is not Operating Confirm the utility power is on (authorized personnel only).

Check the circuit breaker box for tripped circuits (authorized personnel

only).

CLEANING SCHEDULE

Cleaning Daily Weekly Task

Interior/Exterior XClean all glass surfaces with a household or commercial glass

cleaner and a soft cloth.

Clean the deck and shelving surfaces with damp cloth. For

stubborn stains or hardened residue, use hot, soapy water and

soft-bristled brush. Caution! Do not use brushes or pads with

metal bristles or coils to clean this unit as they will scratch

and mar surfaces.

Stainless Steel Surfaces:

• Wash with a solution of hand dishwashing liquid detergent and

water; or a solution of baking soda and water. Rinse and polish

dry with paper towel or soft cloth.

• Never use scouring powders or steel wool as they will scratch

stainless steel.

• Brighten by polishing with a cloth dipped in vinegar or in

ammonia; sprinkle baking soda on sponge and rub gently;

rinse. Polish dry with paper towel.

• Remove streaks or heat stains from stainless steel by rubbing

with club soda.

SERIAL LABEL LOCATION & INFO LISTED / TECH INFO & SERVICE - AMBIENT/HEATED CASES ONLY

--- Sample Serial Label For Ambient/Heated Cases ---

MODEL NRS3648RXV-SAMPLE

SERIAL NO. 12345X30DZ098765

888 E. Porter Rd - Muskegon, MI 49441

3048256

Conforms to UL Std. 65

CERTIFIED TO CAN/CSA

STD C22.2 NO 120

120 VOLTS 60HZ

FOR PARTS OR SERVICE CALL

STRUCTURAL CONCEPTS

AT 1-800-433-9489

SINGLE PHASE 1.84 AMPS

Serial Label Location & Information Listed /

Technical Information & Service

• Serial labels are affixed at a wide range of places

(on the header, at case rear, behind panels or

toe-kicks, on electrical boxes, etc.).

• Serial labels contain electrical information as well

as regulatory standards to which the case

conforms.

• Sample serial label shown below.

• For additional technical information and service, see

the TECHNICAL SERVICE page in this manual for

instructions on contacting Structural Concepts’

Technical Service Department.

Sample QR Code

SCAN FOR PRODUCT LITERATURE

Reveal

Harmony

Fusion

Impulse

Addenda

Blend

Grocerant

Oasis

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Structural Concepts Gewerbliche Lebensmittelgeräte Handbücher

Structural Concepts

Structural Concepts Impulse CSC3223 Bedienungsanleitung

Structural Concepts

Structural Concepts G Series Montageanleitung

Structural Concepts

Structural Concepts GHSS476HRD.5718 Bedienungsanleitung

Structural Concepts

Structural Concepts G Series Bedienungsanleitung

Structural Concepts

Structural Concepts GMDSES8R Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis BV4732 Bedienungsanleitung

Structural Concepts

Structural Concepts Harmony HMO7536R Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis B4732 Montageanleitung

Structural Concepts

Structural Concepts Impulse Series Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis MI44RF Montageanleitung

Structural Concepts

Structural Concepts REVEAL NR3633RSV Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis B3924RH Bedienungsanleitung

Structural Concepts

Structural Concepts Impulse 62486 Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis BD3632 Bedienungsanleitung

Structural Concepts

Structural Concepts BLEND NM4855DSSV Bedienungsanleitung

Structural Concepts

Structural Concepts ADDENDA 86772 Bedienungsanleitung

Structural Concepts

Structural Concepts HVP48SS Montageanleitung

Structural Concepts

Structural Concepts Oasis B32 Bedienungsanleitung

Structural Concepts

Structural Concepts G Series Bedienungsanleitung

Structural Concepts

Structural Concepts G Series Montageanleitung

Structural Concepts

Structural Concepts Reveal NR3613DSV Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis COU2757R Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis BV3632 Bedienungsanleitung

Structural Concepts

Structural Concepts K Series Montageanleitung

Beliebte Gewerbliche Lebensmittelgeräte Handbücher anderer Marken

Blue Seal

Blue Seal EF30 Bedienungsanleitung

Tecfrigo

Tecfrigo Snelle 400 GS Bedienungsanleitung

Follett

Follett PFT Series Bedienungsanleitung

MEFE

MEFE CAT 206 PTR Leitfaden

Premier

Premier 900cl Bedienungsanleitung

Diamond

Diamond AL1TB/H2-R2 Bedienungsanleitung

Salva

Salva IVERPAN FC-18 Bedienungsanleitung

Hussmann

Hussmann Rear Roll-in Dairy Bedienungsanleitung

Cornelius

Cornelius IDC PRO 255 Bedienungsanleitung

Moduline

Moduline HSH E Series Bedienungsanleitung

MINERVA OMEGA

MINERVA OMEGA DERBY 270 Bedienungsanleitung

Cambro

Cambro IBSD37 Bedienungsanleitung

Fri-Jado

Fri-Jado LDR 8 s Bedienungsanleitung

Diamond

Diamond OPTIMA 700 Kurzanleitung

Allure

Allure Melanger JR6t Bedienungsanleitung

saro

saro FKT 935 Bedienungsanleitung

MKN

MKN OPGGSGARG Series Bedienungsanleitung

BIRO

BIRO 22 Service-Handbuch