Structural Concepts Oasis BD3632 Bedienungsanleitung

REV B DATE: 05/04/2023

USER MANUALS\21-29855_OASIS_USER MANUAL_BD3632_BD4732_BD(L)32_REFRIG_SELF-SVC_BOX DOOR CASE

OASIS® REFRIGERATED MODEL BD3632 AND BD4832 BOX DOOR CASE

> SELF-CONTAINED REFRIGERATION SYSTEM (STANDARD)

> REMOTE REFRIGERATION SYSTEM (OPTIONAL)

> FRONT DOOR NON-LOCKING (STANDARD)

> CASE ADJOINMENT POSSIBLE

Oasis

READ AND SAVE THESE INSTRUCTIONS

® USER

MANUAL

--- Model BD4832 (Shown Above) With Two Doors ---

--- Model BD3632 (Shown Above) With One Door ---

Structural Concepts Corp. ∙ 888 E. Porter Rd ∙ Muskegon, MI 49441 Phone: 231.798.8888 Fax: 231.798.4960 ∙ www.structuralconcepts.com

SCC P/N

21-29855

TABLE OF CONTENTS / MODELS TO WHICH THIS MANUAL IS APPLICABLE

OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING / PLUGS …………...

INSTALLATION: CASE REMOVAL FROM SKID / POSITIONING / LEVELER ADJUSTMENT ...…...

GENERAL MERCHANDISER ILLUSTRATION - MODEL BD3632 …...……………………………….

FRONT/REAR PANEL REMOVAL / CONNECTIONS CHECK / TURNING ON POWER TO CASE …..

LED LIGHT FIXTURES .…………………………………………………………………………………..…....

CLEANING SCHEDULE (TO BE PERFORMED BY STORE PERSONNEL) …..……………...…….….

PREVENTIVE MAINTENANCE - TO BE PERFORMED BY TRAINED SERVICE PROVIDERS ....…..

TROUBLESHOOTING (TO BE PERFORMED BY TRAINED SERVICE PROVIDER ONLY) …………

TROUBLESHOOTING - R-290 CONDENSING SYSTEM (BY TRAINED SERVICE PROVIDERS) .....

TROUBLESHOOTING - R-290 EVAPORATOR SYSTEM (BY TRAINED SERVICE PROVIDERS) ....

SERIAL LABEL LOCATION & INFORMATION LISTED / TECH INFO & SERVICE ……….…….……

PROGRAMMABLE CONTROLLER INFORMATION………………………………………..………….…..

TECHNICAL SERVICE CONTACT INFORMATION / WARRANTY INFORMATION …...……………..

3-4

6-9

13-15

16-18

OVERVIEW

• These Structural Concepts merchandisers are designed

to merchandise packaged products at 41 °F (5 °C) or

less product temperatures.

• Product must be pre-chilled to 41 °F (5 °C) or less

product temperatures prior to placing in merchandiser.

• Cases should be installed and operated according to

this operating manual’s instructions to ensure proper

performance.

• Improper use will void warranty.

TYPE II ENVIRONMENTAL CONDITIONS

• This unit is designed for the display of products in

ambient indoor store conditions where temperature and

humidity are maintained within a specific range.

• This Type II display refrigerator is intended for use in an

area where environmental conditions are controlled and

maintained so that the ambient temperature does not

exceed 80 °F (27 °C) and 55% maximum humidity.

COMPLIANCE

• Performance issues when in violation of applicable NEC,

federal, state and local electrical and plumbing codes

are not covered by warranty. See below.

WARNINGS

• This sheet contains important warnings to prevent injury

or death. Please read carefully!

REFRIGERANT DISCLOSURE STATEMENT

• This equipment is prohibited from use in California with

any refrigerants on the “List of Prohibited Substances”

for that specific end-use, in accordance with California

Code of Regulations, title 17, section 95374.

• This disclosure statement has been reviewed and

approved by Structural Concepts and Structural

Concepts attests, under penalty of perjury, that these

statements are true and accurate.

WARNING

Hazardous moving parts. Do not operate unit with covers removed.

Fan blades may be exposed when deck panel is removed.

Disconnect power before removing deck panel.

WARNING

Risk of electric shock. Disconnect power before servicing unit.

CAUTION! More than one source of electrical supply is

employed with units that have separate circuits.

Disconnect ALL ELECTRICAL SOURCES before servicing.

WARNING

Condensate Pan is Hot!

Disconnect and allow to cool before cleaning or removing from case.

WARNING

ELECTRICAL

HAZARD

WARNING

KEEP

HANDS

CLEAR

WARNING

HOT

SURFACE

COMPLIANCE

This equipment MUST be installed in compliance with

all applicable NEC, federal, state and local

electrical and plumbing codes.

OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING / PLUGS - PAGE 1 of 2

ATTENTION

CONTRACTORS

WARNING: This product can expose you to chemicals, including

Urethane (Ethyl Carbamate), which are known to the state of

California to cause cancer and birth defects or other reproductive

harm. For more information go to P65Warnings.ca.gov.

PRECAUTIONS

• This sheet contains important precautions to prevent

damage to unit or merchandise. Please read carefully!

• See previous page for specifics on OVERVIEW,

TYPE, COMPLIANCE and WARNINGS.

OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING / PLUGS - PAGE 2 of 2

WIRING DIAGRAM

• Each case has its own wiring diagram folded and in its

own packet.

• Location: Diagram may be near ballast box, field wiring

box, raceway cover, or other related location.

CAUTION! GFCI BREAKER USE REQUIREMENT

If N.E.C. (National Electric Code) or local code requires GFCI (Ground

Fault Circuit Interrupter), use a GFCI breaker in lieu of a GFCI receptacle.

CAUTION! LAMP REPLACEMENT GUIDELINES

LED lamps reflect specific size, shape and design.

Any replacements must meet factory specifications, resist breakage

and reflect similar appearance as lamps from factory.

CAUTION

CAUTION! POWER CORD AND PLUG MAINTENANCE

Risk of electric shock. If cord or plug becomes damaged,

replace only with cord and plug of same type.

CAUTION! CHECK CONDENSATE PAN, POSITION & CONNECTIONS!

Water on flooring can cause extensive damage!

• Before powering up case, check that condensate pan is positioned directly

under case’s condensate drain.

• Also, check that there are NO LOOSE CONNECTIONS, including overflow

condensate pan and its power cord plug (if part of the condensate package).

CAUTION! DO NOT RELY ON THERMOMETERS OR

THERMOSTATS FOR PRODUCT (FOOD) TEMPERATURES.

• Thermometers & thermostats reflect air temperatures ONLY.

• For ACTUAL product (food) temperatures, use a calibrated food

probe thermometers ONLY.

• For accurate readings, DO NOT use infrared food thermometers.

WIRING DIAGRAM FORMAT & LOCATION

• Each case has its own wiring diagram folded and in its own packet.

• Wiring diagram placement may vary; it may be placed near ballast

box, field wiring box, raceway cover, or other related location.

• Adjoined cases must be connected to each other so that vending

controls system properly communicates with additional case.

Support case

while rolling

down ramp.

Lev

ele

--- Rotated View of Model BD3632 ---

INSTALLATION: CASE REMOVAL FROM SKID / POSITIONING / LEVELER ADJUSTMENT

Shipping

Bracket

Front

Panel

Adjustable

Wrench

Indexing Flat

Pry Bar

1. Disconnect Case From Skid

• Remove front and rear panels.

• Also, remove shipping brackets that

secure casters to skid

• Important! Case is shipped with levelers

in the DOWN position (for stability). To

prevent damage to the case, all levelers

must be raised ALL THE WAY UP before

moving unit off skid and into position.

• After levelers are raised, place ramp up

against skid (to allow case to smoothly

roll off from skid).

2. Roll Case Off Skid via Ramp

• Maintain support of case at all times or

center of gravity may cause case to fall.

• Roll unit to rear of skid.

• Check that ramp is secure and possibly even

attached to skid with screws.

• Carefully roll down ramp and off skid.

3. Position & Align Alongside Other

Cases

• Before adjusting levelers, make certain that the

case is in proper position and, if required,

aligned with adjoining case(s).

• This may require repositioning of the case you

are installing or the already positioned cases.

4. Adjusting Levelers

• Important! After case is in proper position,

levelers must then be LOWERED to floor.

• Adjust levelers so the case is level and plumb.

Depending upon case weight it may be

necessary to use an indexing flat pry

bar (or similar pry bar) to do so.

• Use adjustable wrench to adjust leveler.

• Do not use indexing flat pry bar on

end panel as it may chip.

• Use indexing flat pry bar ONLY on base frame to

avoid damaging case.

• See illustrations at right.

• After case if level and plumb, you may replace

front and rear panels.

Model BD3632 Is Shown. It May

Not Reflect Every Feature or

Option of Your Particular Case.

GENERAL MERCHANDISER ILLUSTRATION - MODEL BD3632 - PAGE 1 of 4

1. Front View of Case

• View is shown with front panel removed (for

electrical box & condenser package viewing).

• Vending controls system (monitor, payment

processor, locks, etc.) is at right side of case.

• Shelves/dividers have weight sensors for product

weighing and pricing.

Condenser

Package

Programmable

Controller

Main Power

Switch

Door Handle

Front Panel

Shown Removed

Shelf (Typ.)

Rear Plenum

Leveler (Typ.)

Thermometer

GENERAL MERCHANDISER ILLUSTRATION - MODEL BD3632 - PAGE 2 of 4

2. Rear View of Case

• Rear panel is shown removed to show access to condenser

package and electrical box.

• Vending Control System is at rear-left of case.

Power Cord

Rear Panel

Shown Removed

Power Cord Slot

Rear Panel

Condenser

Package

Leveler (Typ.)

Model BD3632 Is Shown. It May

Not Reflect Every Feature or

Option of Your Particular Case.

GENERAL MERCHANDISER ILLUSTRATION - MODEL BD3632 - PAGE 3 of 4

3. Self-Contained Hot Gas Loop Condensate Package (Shown Rotated 180°)

• Caution: Only trained service providers are to provide maintenance and service to unit.

• Warning! Disconnect power before providing maintenance and service to unit.

• Important: Carefully read all Warning/Caution/Danger labels on unit!

Compressor

Filter Dryer

Compressor

Inverter

Condenser

Fan & Housing

Courtesy Loop

Condenser Coil

Housing

CleanSweep® Automatic

Condenser Coil Cleaner (Optional)

Hot Gas Loop

Condensate

Pan

Refrigeration

Lines

Model BD3632 Is Shown. It May

Not Reflect Every Feature or

Option of Your Particular Case.

GENERAL MERCHANDISER ILLUSTRATION - MODEL BD3632 - PAGE 4 of 4

5. Evaporator Coil Fans / Air Discharge

When case is energized, refrigeration will be provided.

• Evaporator coil fan should turn on.

• From inside of the case, check for discharge air

from honeycomb discharge duct to confirm that

the fan is functioning properly.

Drain

Wire

Route

Trough

Refrigeration

Line Route

Refrigeration

Lines

TXV

Evaporator

Fan Shroud

• When the case is in a start-up mode or has been

idle for a long period of time, the unit will require

75-minutes of run time to pull-down temperature.

6. TXV (Thermostatic Expansion Valve)

• TXV (at customer front-left side of case).

• Decking must be removed for access.

• See illustration below for TXV location.

Close-Off

Coil

Cover

Tub

Close-Off

Evaporator

Coil

Evaporator Fan

& Blades

FRONT/REAR PANEL REMOVAL / CONNECTIONS CHECK / TURNING ON POWER TO CASE

1. Removable Front/Rear Panel

• Front and rear panel can be removed/replaced

by simply grasping top ‘lip’ and pulling

outward, freeing it from magnets.

• See illustration below.

2. Check Condenser Package Connections

Before Powering Up Case!

• Caution! Connections can come loose

during shipment; this can allow water to

overflow onto floor, causing damage!

• When case in is proper location, remove front

and rear panels to check for loose

connections, including overflow condensate

pan and its power cord plug (if part of the

condensate package).

• See TROUBLESHOOTING section in operating

manual for various troubleshooting issues.

3. Turning On Power To Case

• Plug in power cord.

• Turn on main power switch (at lower left).

• Return front and rear panels to case.

• Check that programmable controller is energized.

• Open door: check that LED light in upper plenum

is energized and that evaporator fans are rotating.

Magnet

Front Panel

Main Power

Switch

Magnet

Magnets

Programmable

Controller

Rear Panel

Model BD3632 Is Shown. It May

Not Reflect Every Feature or

Option of Your Particular Case.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Structural Concepts Gewerbliche Lebensmittelgeräte Handbücher

Structural Concepts

Structural Concepts IMPULSE CGC2830 Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis BV3632 Bedienungsanleitung

Structural Concepts

Structural Concepts Addenda 20-53882 Bedienungsanleitung

Structural Concepts

Structural Concepts GHSS476HRD.5718 Bedienungsanleitung

Structural Concepts

Structural Concepts Impulse Series Bedienungsanleitung

Structural Concepts

Structural Concepts SB5735 Series Montageanleitung

Structural Concepts

Structural Concepts Oasis B4732 Montageanleitung

Structural Concepts

Structural Concepts Oasis B3924RH Bedienungsanleitung

Structural Concepts

Structural Concepts G Series Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis COU2757R Bedienungsanleitung

Structural Concepts

Structural Concepts G Series Montageanleitung

Structural Concepts

Structural Concepts G Series Bedienungsanleitung

Structural Concepts

Structural Concepts BLEND NM4855DSSV Bedienungsanleitung

Structural Concepts

Structural Concepts ADDENDA 86772 Bedienungsanleitung

Structural Concepts

Structural Concepts G Series Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis BV4732 Bedienungsanleitung

Structural Concepts

Structural Concepts G Series Bedienungsanleitung

Structural Concepts

Structural Concepts FUSION Bedienungsanleitung

Structural Concepts

Structural Concepts GHSS1252RLB.6796F Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis B32 Bedienungsanleitung

Structural Concepts

Structural Concepts Impulse 62486 Bedienungsanleitung

Structural Concepts

Structural Concepts HARMONY HMO2653R Bedienungsanleitung

Structural Concepts

Structural Concepts REVEAL NR3633RSV Bedienungsanleitung

Structural Concepts

Structural Concepts Harmony HMO7536R Bedienungsanleitung

Beliebte Gewerbliche Lebensmittelgeräte Handbücher anderer Marken

Blue Seal

Blue Seal EF30 Bedienungsanleitung

Tecfrigo

Tecfrigo Snelle 400 GS Bedienungsanleitung

Follett

Follett PFT Series Bedienungsanleitung

MEFE

MEFE CAT 206 PTR Leitfaden

Premier

Premier 900cl Bedienungsanleitung

Diamond

Diamond AL1TB/H2-R2 Bedienungsanleitung

Salva

Salva IVERPAN FC-18 Bedienungsanleitung

Hussmann

Hussmann Rear Roll-in Dairy Bedienungsanleitung

Cornelius

Cornelius IDC PRO 255 Bedienungsanleitung

Moduline

Moduline HSH E Series Bedienungsanleitung

MINERVA OMEGA

MINERVA OMEGA DERBY 270 Bedienungsanleitung

Cambro

Cambro IBSD37 Bedienungsanleitung

Fri-Jado

Fri-Jado LDR 8 s Bedienungsanleitung

Diamond

Diamond OPTIMA 700 Kurzanleitung

Allure

Allure Melanger JR6t Bedienungsanleitung

saro

saro FKT 935 Bedienungsanleitung

MKN

MKN OPGGSGARG Series Bedienungsanleitung

BIRO

BIRO 22 Service-Handbuch