Structural Concepts Impulse Series Bedienungsanleitung

Rev i Date: 8.27.2019

READ AND SAVE THESE INSTRUCTIONS

Oper Manuals\Impulse\CSC3223_CSC3223-4254_CSC3223-4817_99425.pub

888 E. Porter Road ∙ Muskegon, MI 49441 Phone: 231.798.8888 Fax: 231.798.4960 www.structuralconcepts.com

SELF-SERVICE COUNTERTOP UNITS

>> MODELS CSC3223 / CSC3223.4254 / CSC3223.4817

OPERATING

MANUAL

SCC P/N

99425

Note: See P/N 20-16813 For Field Service Parts List

TABLE OF CONTENTS

OVERVIEW AND WARNINGS ……………….……………..…………………..…….………….....…..………

INSTALLATION ………….…………………………………………………………………………………………

START-UP AND OPERATION ……….. …..….…………………...……………......…..………………………

MAINTENANCE FUNDAMENTALS: SHELF ASSEMBLY REMOVAL / DECKING REMOVAL …………..

MAINTENANCE FUNDAMENTALS: STD. DOOR MECHANISM / RYOBI DOOR MECHANISM ………..

LIGHT FIXTURES - LED ……………………………………………………………………………...………….

SERIAL LABEL LOCATION & INFORMATION LISTED / TECH INFO & SERVICE………………...……..

TROUBLESHOOTING / CLEANING SCHEDULE ……………..………………………….………….………..

ILLUSTRATED PARTS BREAKDOWN (STANDARD CASE ONLY) .……………………….….…...………

ILLUSTRATED PARTS BREAKDOWN (GENERAL) ………………………………………………………….

FIELD SERVICE PARTS LIST …...……………………………………………………………….………………

TECHNICAL SERVICE CONTACT INFORMATION & WARRANTY INFORMATION …................………

CAUTION

OVERVIEW AND WARNINGS

WARNING

ELECTRICAL

HAZARD

OVERVIEW

 The Structural Concepts non-refrigerated service

cases are designed to merchandise unpackaged

bakery products at ambient temperatures.

 These cases should be installed and operated

according to the following instructions to ensure

proper performance.

WARNING

Risk of electric shock.

Disconnect ALL ELECTRICAL SOURCES before servicing.

CAUTION! LAMP REPLACEMENT GUIDELINES

LED lamps reflect specific size, shape and overall design.

Any replacements must meet factory specifications.

CAUTION! GFCI BREAKER USE REQUIREMENT

If N.E.C. (National Electric Code) or your local code

requires GFCI (Ground Fault Circuit Interrupter) protection,

you MUST use a GFCI breaker in lieu of a GFCI receptacle.

COMPLIANCE

This equipment MUST be installed in compliance with

all applicable NEC, federal, state and local electrical codes.

ATTENTION

CONTRACTORS

CAUTION! POWER CORD AND PLUG MAINTENANCE

Risk of electric shock. If cord or plug becomes damaged,

replace only with cord and plug of same type.

WIRING DIAGRAM FORMAT & LOCATION

 Each case has its own wiring diagram folded & in its own packet.

 Wiring diagram placement may vary; it may be placed near ballast

box, field wiring box, raceway cover, or other related location.

WARNING: This product can expose you to chemicals, including

Urethane (Ethyl Carbamate), which are known to the state of

California to cause cancer and birth defects or other reproductive

harm. For more information go to P65Warnings.ca.gov.

 This unit is designed for the display of products in

ambient store conditions where temperatures and

humidity are maintained at a maximum of 75° F

and 55% relative humidity.

COMPLIANCE

 Performance issues when in violation of

applicable NEC, federal, state and local electrical

codes are not covered by warranty.

INSTALLATION

1. Remove Unit From Skid

 Position the unit near a suitable electrical outlet.

 Caution: Case must always remain supported or center of gravity will allow case to fall.

 Slide unit to rear of skid and tip backward off skid.

2. Position and Level Units

For your safety, equipment is furnished with a properly grounded cord connector. Do not attempt to

defeat the grounded connector.

Lift unit with suitable prying bar and blocking. Use care to lift in manner to minimize damage to case.

Rotate leveler to obtain proper height to stabilize and level the unit.

Carefully Slide Unit

Out From Skid

START-UP AND OPERATION

For your safety, equipment is furnished with a properly

grounded cord connector. Do not attempt to defeat

the grounded connector.

1. Set-up Counter Top Unit

 Remove case from skid and place on counter in the

position at which the case will reside.

 Note: The following steps must be completed before

this display case may be put in service.

 1. After case is in position, apply a steady bead of

silicone around the base and counter top.

 2. Allow 24 hours for the silicone to dry before using

the case.

 Electrical 120V stub up connections are provided in

the light switch box.

2. Merchandiser Start-Up

 Do not use an extension cord with this appliance.

 Do not operate this equipment with a damaged cord,

plug or outlet.

 Insure the power switch is off.

 Plug cord into a certified 120V electrical outlet with

ground.

3. LED Lights Only

 Lights will come on when case is plugged in and light

switch is turned on.

4. Tissue Dispenser

 Remove tissue dispenser.

 Place a tissue box into the dispenser as shown.

5. Adjustable Front Storage Area Dividers (Optional)

 Dividers are held in place with magnetic tape strips.

 Dividers may be adjusted to reflect varying widths.

 Dividers may be entirely removed from case.

Light Switch

—— Tissue Dispensers ——

Adjustable Front Storage Dividers

(Retained With Magnetic Tape)

MAINTENANCE FUNDAMENTALS: SHELF ASSEMBLY REMOVAL / DECKING REMOVAL

1. Shelf Assembly Removal

 Shelves can be removed for repositioning,

removal (for individual merchandising

requirements) and cleaning.

 Slide the front shelf support back rotate up and

lift straight up to separate from brackets.

 Slide the rear shelf support back rotate up and

lift straight up to separate from brackets.

Bracket Retainer [Typical]

 Remove brackets. Note: It may be necessary to

remove the nylon shipping bracket retainers.

Pliers will be required to accomplish this task.

2. Decking Removal

 Remove lower shelf assembly.

 Remove interior deck by pushing up from

underneath in the bag storage area.

 See illustration at lower right.

Front Shelf Support

Rear Shelf Support

Shelf Bracket

MAINTENANCE FUNDAMENTALS: STANDARD DOOR MECHANISM / RYOBI DOOR MECHANISM

1. Door “Hold Open” Feature

To reposition the shelving or restock the shelves, it is

first helpful to use the door ‘hold open” feature.

 Open the door all the way (See light fixture).

 Caution damage will result if pin is not

lowered before attempting to close the doors.

 Inside the unit, at the top of each door hinge, is

the pin slide cover.

 Slide the pin cover up until the pin extends

approximately 1/2 inch above the door hinge.

 Release the door assembly allowing the pin to rest

on the outer door frame.

 To close, fully open the door and retract the pin into

the hinge and allow the door to close.

2. Ryobi Door Closing Mechanism (Optional)

 Certain models (such as CDR4817) use the Ryobi

door closing mechanism.

 When opened approximately 90°, door ‘catches’

and stays open.

 When pressure is applied to close door, ‘catch’

releases and door closes normally. PIN EXTENSION

Ryobi Door

Closing

Mechanism

Ryobi Inner

Arm

Ryobi Outer

Arm

Ryobi Pivot

Bracket

Door

LIGHT FIXTURES - LED

View of case with decking removed to access

LED Light

Assemblies

(Inside

Edge

Both Sides)

LED

Power

Supply

Box

Decking

Magnetic Mounting

Clip View #2

LED

Lights

Plug

Barrel

Shaped

Insert

LED

Light

Magnetic Mounting

Clip View #1

No Gap

Gap

LED Style Light Fixtures

Removal of Faulty LED Lights:

 LED lights rarely require change-out.

 Contact Structural Concepts’ Technical Service

Department for replacement LED lights.

 Turn off LED light switch.

 To remove faulty LED light, follow these steps:

A. Disconnect plug from LED light.

B. Using both hands, grasp LED light assembly

(with its magnetic mounting clips). Pull

downward and off its shelf (or header).

C. Remove magnetic mounting clips from LED

light by pressing against flange part of clip

with thumb.

>> Note: Mounting clips MAY be riveted to shelf or

header. In such instances, simply remove LED light

from mounting clips by pressing against flange part

of clips with thumb.

Replacement of LED lights:

 Attach magnetic mounting clips onto LED light.

 Adjust magnetic mounting clips so they are equally

spaced on LED light.

 Reattach LED light assembly to its shelf/header.

 Position properly in shelf/header.

>> Note: If mounting clips are riveted to shelf (or

header), attach by placing LED in base of clip and

then snapping into clip at FLANGE SIDE.

 Press plug’s barrel-shaped insert all the way into

LED light.

 Important: If plug is not inserted ALL THE WAY IN

the LED light’s orifice, the light may not energize.

See “BAD” vs. “GOOD” insertion illustrations

below-right.

 Turn LED light switch back on.

SERIAL LABEL LOCATION & INFORMATION LISTED / TECH INFO & SERVICE

Serial Label Location & Information Listed / Technical Information & Service

 Serial labels are located near the electrical access on your case.

 Serial labels contain electrical, temperature & refrigeration information, as well as regulatory

standards to which the case conforms.

 For additional technical information and service, see the TECHNICAL SERVICE page in this

manual for instructions on contacting Structural Concepts’ Technical Service Department.

 See images below for samples of both refrigerated and non-refrigerated serial labels.

----- Sample Serial Label For Non-Refrigerated Case -----

TROUBLESHOOTING / CLEANING SCHEDULE

Issue Resolution

Case Lights Not Working Check LED lights for proper installation and connection. See

LIGHT FIXTURES - LED section in manual for illustrations.

Check for burned out LED lights.

System is not Operating Confirm the utility power is on.

Check the circuit breaker box for tripped circuits.

Troubleshooting

Cleaning Schedule

Cleaning Daily Weekly Monthly Task

Clean Case Exterior XClean all case exterior surfaces with a household or

commercial glass cleaner and a soft cloth.

Clean Case Interior XClean the interior case deck and shelving surfaces

with a warm water and mild soap solution.

Andere Handbücher für Impulse Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Structural Concepts Gewerbliche Lebensmittelgeräte Handbücher

Structural Concepts

Structural Concepts REVEAL NR3633RSV Bedienungsanleitung

Structural Concepts

Structural Concepts GHSS1252RLB.6796F Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis B3924RH Bedienungsanleitung

Structural Concepts

Structural Concepts Reveal NR3613DSV Bedienungsanleitung

Structural Concepts

Structural Concepts Impulse CSC3223 Bedienungsanleitung

Structural Concepts

Structural Concepts IMPULSE CGC2830 Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis COU2757R Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis B4732 Montageanleitung

Structural Concepts

Structural Concepts ENCORE Series Montageanleitung

Structural Concepts

Structural Concepts G Series Bedienungsanleitung

Structural Concepts

Structural Concepts Impulse 62486 Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis BD3632 Bedienungsanleitung

Structural Concepts

Structural Concepts FSE663R Bedienungsanleitung

Structural Concepts

Structural Concepts grocerant DP8HP60WD.5718B Montageanleitung

Structural Concepts

Structural Concepts GHSS476HRD.5718 Bedienungsanleitung

Structural Concepts

Structural Concepts G Series Bedienungsanleitung

Structural Concepts

Structural Concepts SB5735 Series Montageanleitung

Structural Concepts

Structural Concepts G Series Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis MI44RF Montageanleitung

Structural Concepts

Structural Concepts BLEND NM4855DSSV Bedienungsanleitung

Structural Concepts

Structural Concepts K Series Montageanleitung

Structural Concepts

Structural Concepts G Series Montageanleitung

Structural Concepts

Structural Concepts Oasis BV4732 Bedienungsanleitung

Structural Concepts

Structural Concepts Addenda 20-53882 Bedienungsanleitung

Beliebte Gewerbliche Lebensmittelgeräte Handbücher anderer Marken

Blue Seal

Blue Seal EF30 Bedienungsanleitung

Tecfrigo

Tecfrigo Snelle 400 GS Bedienungsanleitung

Follett

Follett PFT Series Bedienungsanleitung

MEFE

MEFE CAT 206 PTR Leitfaden

Premier

Premier 900cl Bedienungsanleitung

Diamond

Diamond AL1TB/H2-R2 Bedienungsanleitung

Salva

Salva IVERPAN FC-18 Bedienungsanleitung

Hussmann

Hussmann Rear Roll-in Dairy Bedienungsanleitung

Cornelius

Cornelius IDC PRO 255 Bedienungsanleitung

Moduline

Moduline HSH E Series Bedienungsanleitung

MINERVA OMEGA

MINERVA OMEGA DERBY 270 Bedienungsanleitung

Cambro

Cambro IBSD37 Bedienungsanleitung

Fri-Jado

Fri-Jado LDR 8 s Bedienungsanleitung

Diamond

Diamond OPTIMA 700 Kurzanleitung

Allure

Allure Melanger JR6t Bedienungsanleitung

saro

saro FKT 935 Bedienungsanleitung

MKN

MKN OPGGSGARG Series Bedienungsanleitung

BIRO

BIRO 22 Service-Handbuch