Teledyne Lecroy ZD200 Bedienungsanleitung

Operator’s Manual

ZD200 Differential Probe

Operator’s Manual

February, 2021

ZD200 Differential Probe Operator’s Manual

Users are permitted to duplicate and distribute Teledyne LeCroy

documentation for internal training purposes only. Resale or unauthorized

duplication of Teledyne LeCroy documentation materials is strictly

prohibited.

Teledyne LeCroy is a registered trademark of Teledyne LeCroy, Inc. Other

product or brand names are trademarks or requested trademarks of their

respective holders. Information in this publication supersedes all earlier

versions. Specifications are subject to change without notice.

933098-00 Rev A

zd200-differential-probe-om.pdf

February, 2021

Operator’s Manual

Table of Contents

Safety Instructions ................................................................................1

Introduction...........................................................................................2

Key Features ..............................................................................................2

Standard Accessories ...............................................................................3

Probe Operation ....................................................................................4

Handling the Probe....................................................................................4

Connecting the Probe to an Oscilloscope ...............................................4

Connecting the Probe to the Test Circuit ................................................4

Operation with an Oscilloscope................................................................5

Auto Zero....................................................................................................5

Care and Maintenance...........................................................................6

Cleaning......................................................................................................6

Calibration Interval ....................................................................................6

Service Strategy.........................................................................................6

Replacement Parts ....................................................................................6

Performance Verification.......................................................................7

Required Test Equipment .........................................................................7

Preliminary Procedure...............................................................................9

Functional Check .......................................................................................9

Verification Procedure............................................................................ 10

ZD200 Test Record................................................................................. 11

Reference Material ..............................................................................12

Certifications........................................................................................... 12

Returning a Product for Service ............................................................ 13

Technical Support .................................................................................. 15

ZD200 Differential Probe

Warranty

Teledyne LeCroy warrants this oscilloscope accessory for normal use and

operation within specification for a period of one year from the date of

shipment. Spare parts, replacement parts and repairs are warranted for 90

days.

In exercising its warranty, Teledyne LeCroy, at its option, will either repair or

replace any assembly returned within its warranty period to the Customer

Service Department or an authorized service center. However, this will be

done only if the product is determined by Teledyne LeCroy’s examination to

be defective due to workmanship or materials, and the defect is not caused

by misuse, neglect, accident, abnormal conditions of operation, or damage

resulting from attempted repair or modifications by a non-authorized service

facility.

The customer will be responsible for the transportation and insurance

charges for the return of products to the service facility. Teledyne LeCroy will

return all products under warranty with transportation charges prepaid.

This warranty replaces all other warranties, expressed or implied, including

but not limited to any implied warranty of merchantability, fitness or

adequacy for any particular purposes or use. Teledyne LeCroy shall not be

liable for any special, incidental, or consequential damages, whether in

contract or otherwise.

Operator’s Manual

Safety Instructions

This section contains instructions that must be observed to keep this

oscilloscope accessory operating in a correct and safe condition. You are

required to follow generally accepted safety procedures in addition to the

precautions specified in this section. The overall safety of any system

incorporating this accessory is the responsibility of the assembler of the

system.

Symbols

These symbols may appear on the probe body or in this manual to alert you

to important safety considerations.

CAUTION. Potential for damage to probe or instrument it is connected

to. Attend to the accompanying information to protect against personal

injury or damage. Do not proceed until conditions are fully understood

and met.

ELECTROSTATIC DISCHARGE (ESD) HAZARD. The probe is susceptible

to damage if anti-static measures are not taken.

DOUBLE INSULATION

Precautions

Connect and disconnect properly. Connect probe to the measurement

instrument before connecting the test leads to a circuit/signal being tested.

Use only within operational environment listed. Do not use in wet or

explosive atmospheres.

Use indoors only.

Keep product surfaces clean and dry.

Be careful with sharp tips. The tips may cause bodily injury if not handled

properly.

Do not operate with suspected failures. Do not use the probe if any part is

damaged. Cease operation immediately and sequester the probe from

inadvertent use.

ZD200 Differential Probe

Operating Environment

The accessory is intended for indoor use and should be operated in a clean,

dry environment. Before using this product, ensure that its operating

environment is maintained within these parameters:

Temperature: 5° to 40° C

Humidity: Maximum relative humidity 90 % for temperatures up to 31° C

decreasing linearly to 50 % relative humidity at 40° C

Altitude: Up to 10,000 ft (3,048 m)

Introduction

The ZD200 Differential Probe is ideally suited for automotive and serial data

signals. The wide dynamic range (+/- 20V differential) and 1 MOhm input

resistance make the ZD200 ideally suited for a wide range of applications.

The ZD200 probe can be used with a variety of Teledyne LeCroy

oscilloscopes running MAUI firmware version 6.4.1.x or later. See the

oscilloscope product page at teledynelecroy.com/oscilloscopes for probe

compatibility.

With the ProBus interface, the ZD200 probe becomes an integral part of the

oscilloscope, able to be controlled from the oscilloscope’s front panel. The

oscilloscope provides power to the probe, so there is no need for a separate

power supply or batteries.

Key Features

Key Benefits

Features

1 MOhm input resistance

Low input capacitance

Wide dynamic range

ProBus interface

Small, low mass probe head is designed

for ease of use and high performance.

Probe tip socket fits easily onto 0.025

inch square pins for direct access to test

points. Several available adaptors

connect directly to the probe socket.

Complete accessory kit.

Operator’s Manual

Standard Accessories

The ZD200 probe is provided with numerous accessories to make probing

different test points easier than ever. The probe is also supplied with an

Operator’s Manual and a Certificate of Calibration.

Accessory

Quantity

Description

Hook Clips

Micro-Grabbers

Ideal for connecting to small IC legs or

very tightly spaced pins

Micro-IC Grabbers

Straight Tips

Designed to connect to the smallest

vias and small test points. Fits in either

probe socket.

12.8mm and 16.8mm

Dual Pin Sets

2 ea.

5cm and 10cm

Extension Leads

2 ea.

Have a socket on one end and a

square pin on the other to connect to

the input or ground socket of the

probe body, and may be used for

general purpose probing.

Y Leadset

Used for both ground and input lead

simultaneously. It has two sockets on

one end for connection to the

provided hook clips and two square

pins on the other and may be used for

general purpose probing.

ZD200 Differential Probe

Probe Operation

Handling the Probe

The ZD200 probe is a precision test instrument. Exercise care when handling

and storing the probe. Always handle the probe by the probe body or

compensation box. Avoid putting excessive strain or exposing the probe

cable to sharp bends.

ESD Sensitive: The tips of the ZD200 probes are sensitive to

Electrostatic Discharge (ESD). Avoid causing damage to the probe

by always following anti-static procedures (wear wrist strap, etc.)

when using or handling the probe.

Connecting the Probe to an Oscilloscope

The ZD200 probe has been designed for use with Teledyne LeCroy platforms

equipped with the ProBus interface. When you attach the probe output

connector to the oscilloscope’s input connector, the oscilloscope recognizes

the probe, provides proper termination and activates the probe control

functions in the user interface.

Connecting the Probe to the Test Circuit

To maintain the high performance capability of the probe in measurement

applications, care must be exercised in connecting the probe to the test

circuit. Increasing the parasitic capacitance or inductance in the input paths

may introduce a “ring” or slow the rise time of fast signals. Input leads which

form a large loop area will pick up any radiated electromagnetic field which

passes through the loop and may induce noise into the probe input.

Using one of the available accessories makes the ZD200 probe with its small

profile and low mass head ideally suited for applications in dense circuitry.

Inhaltsverzeichnis

Andere Teledyne Lecroy Messgerät Handbücher

Teledyne Lecroy

Teledyne Lecroy Frontline NFC-F Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVD3102 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook DL02-HCM Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP008 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook CP030B Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVD3000 Series Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy RP2060 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PCI Express Gen 4x8 OCuLink Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PCI Express 2.0 Mid-Bus Probe Einrichtungshandbuch

Teledyne Lecroy

Teledyne Lecroy Summit T416 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveRunner 8000-R Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy ZS Series Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Frontline BPA 500 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook DL05-HCM Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Frontline SD Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Quantumdata 780E Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Summit T3-8 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PCI Express 5.0 U.2 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP016 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy AP033 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy MDA800A Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy frontline SODERA Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP016 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVD3000 Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung