Tornado 93012B Handbuch
TORNADO INDUSTRIES, LLC
3101 WICHITA COURT
FORT WORTH, TX 76140
PHONE: 800-VACUUMS
FAX: 817-551-0719
WWW.TORNADOVAC.COM
Operations & Maintenance Manual
For Commercial Use Only
Form No. L3012M BE05/20 ©Tornado Industries, LLC. All rights reserved
Pac-Vac™ 6 Aircomfort/Pac-Vac™ 10 Aircomfort
MODEL NO: 93012B/93014B
2
NOTES
For warranty information go to www.tornadovac.com
3
IMPORTANT SAFETY INSTRUCTIONS
FOR COMMERCIAL USE
WHEN USING AN ELECTRICAL APPLIANCE, BASIC PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:
• Do not leave machine unattended when plugged in. Unplug from outlet when not in use and
before changing pads or attempting any maintenance or adjustment. If handle switch lever is
activated accidentally, high starting torque will cause machine to move and may cause damage or
injury.
• To avoid electrical shock, Use indoors only. Do not use outdoors and do not expose to rain.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Use only as described in this manual. Use only manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If machine is not working properly, if it was dropped,
damaged, left outdoors, or dropped into water, return it to a service center.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp
edges or corners. Do not run machine over cord. Keep cord away from heated surfaces. Do not
unplug by pulling on cord. To unplug, grasp the plug not the cord.
• Do not handle plug or machine with wet hands.
•Keep hair, loose clothing, ngers, and all parts of body away from openings and moving parts.
• Turn off all controls before unplugging.
• Connect to a properly grounded outlet only. See Grounding Instructions.
• Do not put hands under base - rotating parts could cause injury.
•Always keep hands feet and loose tting clothing away from moving parts to prevent possible
injuries.
•Use care to keep electrical supply cable from contacting moving parts, such as oor brushes or
pads.
• Risk of explosion: Floor sanding can result in explosive mixture of ne dust and air. Use this
machine only in a well-ventilated area, free from any ame or match.
•Do not use machine in areas where ammable and/or explosive vapors or dusts are present.
•To avoid res do not use with a ammable or combustible liquid to clean a oor.
• Make sure voltage and frequency at the wall receptacle correspond with that indicated on
nameplate before plugging in machine.
• Use only a 12 Ga. three-wire extension cable, which have 3-prong grounding type plugs and
3-prong receptacles that accept the plug of the machine.
• Use extra care when cleaning on stairs.
• Do not pick up anything that is burning or smoking such as cigarettes, matches, or hot ashes.
•Do not use without dust bag and/or lters in place.
SAVE THESE INSTRUCTIONS
4
GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of
least resistance for electric current to reduce the risk electric shock. This machine is equipped with a
cord having an equipment -grounding conductor and grounding plug. The plug must be inserted into
an appropriate outlet that is properly installed and grounded in accordance with all local codes and
ordinances.
WARNING: Improper connection of the equipment-grounding conductor can result in a risk of electric
shock. Check with a qualied electrician or service person if you are in doubt as to whether the outlet
is properly grounded. Do not modify the plug provided with the appliance - if it will not t the outlet,
have a proper outlet installed by a qualied electrician.
This appliance is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the
plug illustrated in sketch A.
Sketch A
5
• You must be trained in the operation of this machine before use. Please read this manual carefully and obtain operation instructions
from your safety director or your authorized Tornado distributor.
• Always operate this machine with all of the cable removed from the handle. Failure to do so will upset the precision balance of the
machine.
• Do not use the Floor Machine for scarifying or sanding.
• Care should be taken to keep cable away from rotating brush.
• Do not attempt to repair warranted machines. All repairs must be done by a qualied and authorized repair center. Non warranted
repairs will be billed back to the owner of the unit.
• Do not use any replacement parts except those specied in the parts list. Unauthorized parts could cause the unit to malfunction and
will void the warranty.
FAILURE TO COMPLY WITH THE ABOVE WARNING INSTRUCTIONS
WILL VOID THE WARRANTY
SAFETY PRECAUTIONS
Do not operate the vacuum while it is standing on high pile carpet/ It is essential that the exhaust
airow not be restricted
Do not wash or launder the cloth bag as this will destroy the ltration capacity of the fabric.
WHEN THE MACHINE IS DELIVERED
Check the carton carefully for signs of rough handling. Remove the machine from the carton and look for concealed damage. If the
machine is damaged, notify the carrier immediately and request an inspection. Be sure to keep the carton, packing inserts, packing
lists, and carrier’s receipt until the inspector has veried your claim.
BEFORE OPERATING THE MACHINE
Read the manual carefully and completely before attempting to operate the unit. This manual has important information for the use and
safe operation of the machine. FAILURE TO ADHERE TO THESE INSTRUCTIONS COULD RESULT IN SERIOUS BODILY INJURY
OF PROPERTY DAMAGE. Keep this manual on le and handy. This machine will assure years of satisfactory service if operated and
maintained according to recommendations in the manual. If additional information is needed, please contact your local distributor or
write to:
TORNADO INDUSTRIES
3101 Wichita Ct.
Fort Worth, TX 76140
1-800-VACUUMS
All information and specications printed in the manual and parts list are current at the time of printing. However, because of Tornado’s
policy of continual product improvement, we reserve the right to make changes at any time without notice.
WARRANTY
To protect your investment, promptly ll out the
required information on the warranty card that
comes with the unit and mail it back to
Tornado Industries
Note: Service repair and warranty work
is not normally handled at the factory.
WARNING
The machine was designed for use on oors as per instructions
and recommendations written in this manual. Any deviation from its proper use or purpose and the consequential
damage that may occur is the sole responsibility of the end user.
GENERAL PRECAUTIONS
6
OPERATION INSTRUCTIONS
Please read the following operating instructions carefully. They will help you to get the best
performance from this professional quality vacuum cleaner and to maintain it in optimum condition.
Follow these simple steps for easy and effective operation of the Backpack vacuum.
Open the lid and ensure that the cloth bag is correctly located and the exible ring provides a proper
seal when the lid is closed. For optimum performance, ltration and maximum hygiene, it is advisable
to use a paper vacuum bag in addition to the standard cloth bag.
If a paper vacuum bag is used, simply insert it into the cloth bag, making sure that the cardboard disk
is centered on the exible sealing ring. When you replace the lid, the short nozzle in the center of the
lid will be forced into the central hole of the cardboard disk of the paper vacuum bag thus providing
a tight seal. Make sure the paper vacuum bag is tightly secured over the short nozzle before
vacuuming.
Lock the lid down with the two latches. Always ensure that the cloth vacuum bag is empty and the
paper bag is no more than ½ full before vacuuming. The Backpack vacuum has been tted with
a thermal overload switch to protect the motor against damage should the airow be blocked for
extended periods. This may occur if the vacuum bag is overfull, the cloth lter bag is clogged or if
the vacuum hose or exhaust is blocked. The vacuum motor will stop before it can get too hot. If
this happens, empty and thoroughly clean the vacuum bag and HEPA lter or free any blockage and
ensure that adequate airow is restored. After the motor has cooled to a safe operating temperature,
locate the thermal reset switch on the bottom of the unit and push it back in. There will be a slight
audible click. Now the motor will restart.
1. The vacuum hose is tted into the cuff in the lid. It should not be necessary to remove the
hose in normal operation.
2. Place the Backpack vacuum on your back, adjust the shoulder straps until you feel comfortable
and then tighten the waist belt. The Backpack vacuum is designed to ride higher on your back
for maximum comfort.
3. Plug the cord into a 110 volt, grounded outlet. Always unwind the cord completely before
vacuuming. It is important to maintain the power cord in good condition. This unit ships with
a 50’ 16/3 SJT power cord. Use care when pulling the cord around sharp edges and through
doorways.
Never operate the Backpack vacuum if the power cord is damaged in any way.
4. Attach the extension wand to the hose and t the oor tool or any of the other vacuuming
accessories on the wand.
5. Turn the vacuum on. The toggle switch is located on the switch box. The switch box is afxed
to the waist belt.
6. After you nish cleaning, turn off the main power switch and unplug the cord from the wall
outlet. Then starting from the Backpack vacuum, wrap up the cord to store. Be careful not to
pull or yank on the vacuum cleaner’s power cord.
7
• Turn off the main power switch and unplug unit from wall outlet (Fig. 1).
• Remove vacuum hose from top of unit (Fig 2).
• Release the two latches and lift off lid (Fig. 3).
• Separate lid from paper bag insert and dispose of paper bag (Fig. 4)
•Remove cloth lter bag, clean, dust and replace (Fig. 5).
• Insert new paper bag making sure to align lid nozzle with bag hole and replace latches (Fig. 6)
TO CHANGE THE FILTER COLLECTION BAGS
CHANGING EXHAUST FILTER ASSEMBLY
The Pac-Vac vacuum cleaner is equipped with a HEPA lter and an exhaust lter. These lters
capture ne dust particles and protect the motor from dirt. It is important to replace the HEPA lter
approximately every six months. Replace the exhaust lter every fourth time the paper vacuum bags
changed.
To change or clean the exhaust lter
1. Turn off the main power switch and unplug unit from wall outlet (Fig. 1).
2. Detach the exhaust lter holder from the bottom of the unit (Fig. 7)
3. Remove the exhaust lter from the holder (Fig. 8)
4. DO NOT THROW AWAY THE FILTER HOLDER.
5. Remove the exhaust lter from the plastic holder and shake or brush dirt from the lter.
6. Replace the exhaust lter in the plastic holder and place into vacuum.
Fig. 1 Fig. 2 Fig. 3 Fig. 4
Fig. 5 Fig. 6
Fig. 7 Fig. 8
8
MAINTENANCE
Clean the cloth vacuum bag regularly. After emptying the vacuum bag, turn it inside out and shake as
much dust out of the fabric as possible. Optimum performance is achieved by using a paper lter bag
with the cloth bag.
Clean the vacuum bag and HEPA lter or free any blockage and ensure that adequate airow is
restored.
Use only approved Tornado paper lter bags.
Check the power cord for damage and replace if damaged.
Always unwind the cord completely.
Ensure the vacuum hose, the extension wand and the vacuuming accessories are not blocked.
Ensure that the electrical outlet and the plug are securely connected. Incorrect connections may
cause sparking and damage to the cable socket.
Have your unit serviced by an authorized repair service center if you suspect any potential problems.
Ensure that the exible vacuum bag ring provides a proper seal before vacuuming.
Recommended replacement parts:
Pac-Vac™ Aircomfort Vacuum Cleaner
C352-2500 Paper Bag (10 pack) 90312
B352-7800 Paper Bag (10 pack) 90314
B352-2400 Motor Exhaust Micro Filter
B352-2401 HEPA Filter
C352-1400 Shake Out Bag 90312
C352-1500 Shake Out Bag 90314
C352-2800 Switch Harness
B352-6800 Strain Relief Complete
B352-3200 Power Harness
D113-3400 Motor
X9714 Power Cord
CHANGING HEPA FILTER ASSEMBLY
To change the HEPA lter:
1. Unplug the unit. Remove the lid, paper bag and cloth bag to expose the HEPA lter.
2. Remove the lter cap on the top of the HEPA lter (Fig. 9)
3. Remove the HEPA lter from the dust compartment
4. Insert a new HEPA lter and replace the lter cap (Fig. 10). Ret the cloth bag, paper bag, and
replace lid.
Note: The HEPA lter can NOT be washed and reused.
Fig. 9 Fig. 10
9
1
2
3
4
5
7
6
8
No. Part No. Description
1A352-6900 Hose
2CT171 Wand
3CT176 Crevice Tool
4 B352-PF10 Carpet Tool
5 CT188 Upholstery Tool
6 CT184 Dusting Tool
7C352-PF20 Hard Floor Tool
8CT190Easy Glide Carpet Tool
2
REMARQUES
Pour des informations sur la garantie, visitez
www.tornadovac.com
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Sprachen:
Andere Tornado Staubsauger Handbücher
Tornado
Tornado 4000 SERIES Leitfaden
Tornado
Tornado CVD 38/2 Bedienungsanleitung
Tornado
Tornado TASKFORCE 97060 CFV 10 Handbuch
Tornado
Tornado 97130 Handbuch
Tornado
Tornado 95995 Bedienungsanleitung
Tornado
Tornado Marathon 350 98132 Handbuch
Tornado
Tornado CK LW 13/1 Handbuch
Tornado
Tornado 125 Handbuch
Tornado
Tornado 94220 Handbuch
Tornado
Tornado ExSELLerate Marathon 350 Handbuch
Tornado
Tornado TV2 Handbuch
Tornado
Tornado Bolido Bedienungsanleitung
Tornado
Tornado Pro PAC Handbuch
Tornado
Tornado Taskforce 15 Trot-Mop Handbuch
Tornado
Tornado TO420 Bedienungsanleitung
Tornado
Tornado ExSELLerate Series Einrichtungshandbuch
Tornado
Tornado TO 6150 Bedienungsanleitung
Tornado
Tornado 98145 Bedienungsanleitung
Tornado
Tornado CVD 30/1 Bedienungsanleitung
Tornado
Tornado PS Series Handbuch
Beliebte Staubsauger Handbücher anderer Marken
Bissell
Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung
Panasonic
Panasonic MC-YL637S147-AE Bedienungsanleitung
NEFF
NEFF N17XH10 0 Series Bedienungsanleitung
LG
LG A9 Series Bedienungsanleitung
Oreck
Oreck Cordless Captura BK51700 Series Bedienungsanleitung
Kogan
Kogan KAVACROBVWA Bedienungsanleitung
