Ubiquiti AirFiber AF-11 Bedienungsanleitung

airFiber AF-11 Radio* Zip Ties (Qty. 2) airFiber Gigabit PoE (50V,

1.2A)

Power Cord AF-11G35 Antenna Shroud

I-Bracket Upper Mount Bracket with

Elevation Rod

Lower Mount Bracket

Pole Clamps (Qty. 2) Azimuth Support Brackets (Qty.

RF Cables (Qty. 2)

Large Carriage Bolts (Qty. 4) Small Carriage Bolts (Qty. 2) Serrated Flange Bolts (Qty. 4)

Bolts with Washers (Qty. 4) Serrated Flange Nuts (Qty. 6)

Package Contents

* Comes with (1) Low-Band or (1) High-Band Duplexer pre-installed for SISO mode. For MIMO

mode, a second Duplexer is available, model AF-11-DUP-L or AF-11-DUP-H.

Installation Requirements

Clear line of sight between airFiber radios

Vertical mounting orientation

Mounting point:

At least 1 m below the highest point on the structure

For tower installations, at least 3 m below the top of the tower

Ground wires – min. 10 AWG (5 mm ) and max. length: 1 m. As a safety precaution,

ground the airFiber radio to grounded masts, poles, towers, or grounding bars.

(Optional) MIMO mode: A second Duplexer of the same band type: Low-Band

Duplexer (model AF-11-DUP-L) or High-Band Duplexer (model AF-11-DUP-H):

WARNING: Failure to properly ground your airFiber radio will void your

warranty.

AF11-Complete Quick Start Guide

(Optional) If not using PoE: DC power source and 12/30 AWG power cable

Outdoor, shielded Category 6 (or above) cabling and shielded RJ-45 connectors are

required for all wired Ethernet connections.

(Recommended) Surge protection should be used for all outdoor installations. We

recommend that you use two Ethernet Surge Protectors, model ETH-SP-G2, one

within one meter of the device and the other at the entry point to the building. The

ETH-SP-G2 will absorb power surges and safely discharge them into the ground.

Hardware Overview

Note: The AF-11 radio has one Duplexer pre-installed for SISO mode. For

MIMO mode, a second Duplexer must be purchased separately. The

Duplexer(s) must match the terms of your license (frequency bands and

polarities allowed).

Note: For guidelines about grounding and lightning protection, follow your

local electrical regulatory codes.

AF11-Complete Quick Start Guide

Chain 0 / Chain 1

Signal LEDs

Link LED

Low-Band Duplexer High-Band Duplexer

When the Chain 0 or Chain 1 duplexer is installed, its N-type connector is located

here, allowing connection to an RF cable (Chain 1 is covered by the removable

Duplexer Cap).

Signal 4 LED will light blue when on.

Signal 3 LED will light green when on.

Signal 2 LED will light yellow when on.

Signal 1 LED will light red when on.

Bootup to airOS When powering on, the Power, MIMO, LINK, and Signal 1-4 LEDs

light on. Once the CPU code takes over, the MIMO, LINK, and Signal 1-3 LEDs turn

off. Signal 4 LED remains lit to indicate the boot sequence is underway.

Initializing airFiber Software When the airFiber application begins to boot under

airOS, the Signal 4 LED goes from solidly on to a 2.5 Hz flash. This continues until

the device is fully booted.

Signal Level Once fully booted, the Signal 1-4 LEDs act as a bar graph showing how

close the device is to ideal aiming. This is auto-scaled based on the link range, the

antenna gains, and the configured TX power of the remote device. Each Signal LED

has three possible states: On, Flashing, and Off. All Signal LEDs would be solidly on

in an ideal link. For example, if the link has a 1 dB loss, the Signal 4 LED will flash; a

2 dB loss and the Signal 4 LED will turn off. The full bar graph LED states are shown

below.

dB loss

0 -1 -2 -3 -4 -5 -6

-7 -8 -9 -10 -11 -12 -13

Off RF Off

Syncing

Beaconing

AF11-Complete Quick Start Guide

MIMO LED

MGMT LED

Data LED

Power LED

Management Port

Reset Button

Data Port

VDC IN

TX 0, RX 0

RX 1, TX 1

N Connector

SMA Port

Registering

On Operational

Off Radio Configured in SISO Mode

On Radio Configured in MIMO Mode

Off No Ethernet Link

On Ethernet Link Established

Random Flash Ethernet Activity

Off No Ethernet Link

On Ethernet Link Established

Random Flash Ethernet Activity

Off No Power

On Powered On

10/100 Mbps, secured Ethernet port for configuration. In-Band Management is

enabled by default in the airFiber Configuration Interface. When In-Band

Management is disabled, the MGMT port is the only port that can monitor, configure,

and/or update firmware.

To reset to factory defaults, press and hold the Reset button for more than 10

seconds while the device is already powered on.

Gigabit PoE port for handling all user traffic and powering the device.

The terminal block can be used to power the AF‑11 radio with +50VDC, 1.2A instead

of PoE.

The TX and RX SMA ports for the Chain 0 Low-Band Duplexer or High-Band

Duplexer (SISO and MIMO modes).

The RX and TX SMA ports for the Chain 1 Low-Band Duplexer or High-Band

Duplexer (MIMO mode). In SISO mode, these unused ports are protected by the

Duplexer Cap.

Female N-type connector to which the antenna cable is attached.

High-band and low-band channel SMA ports.

Note: One Low-Band Duplexer or High-Band Duplexer is pre-installed in the

radio for SISO mode. MIMO mode requires two Duplexers of the same band

type.

Installation Overview

We recommend that you configure your paired radios before site installation.

Install the Duplexer(s) in the radio.

Connect the airFiber Gigabit PoE adapter to the DATA port, and connect your

computer to the MGMT port.

Configure the radio.

Install a ground wire and mount the radio on the airFiber AF-11G35 antenna (or a

compatible antenna).

At the installation site, install the antenna with the mounted radio (see the antenna’s

AF11-Complete Quick Start Guide

Quick Start Guide for installation instructions).

Connect the DATA port to your LAN, and connect power (PoE or DC power) to the

radio.

Establish and optimize the RF link.

Installing the Duplexers

SISO Mode Installation

Each AF-11 radio already contains one Low-Band Duplexer or one High-Band Duplexer

for SISO mode. However, before you install the radios, you must ensure that Duplexers

in the paired radios are positioned in the reverse order from each other.

Note: For example, if the numbers on the first radio’s Duplexer are (left to right)

1/3, then the numbers on the second radio’s Duplexer should be 3/1.

Radio 1 Radio 2

Ensure that the Duplexers in your paired radios are installed in this manner. For

instructions on how to access the Duplexers and remove or install them, see “MIMO

Mode Installation”.

MIMO Mode Installation

Note: MIMO operation requires two licenses, one per polarization, and two

Duplexers of the same band type.

Note: Position the low channel and high channel ports to yield the required

transmit and receive frequencies. Also, ensure that the numbers on the right-

side Duplexer are in the reverse order of the numbers on the left-side

Duplexer.

AF11-Complete Quick Start Guide

WARNING: Tighten the collars alternately, a half turn at a time, until both are

fully tightened. Failure to do so may result in damage to the Duplexer.

6. Repeat steps 1-5 for the other radio in the link, ensuring that the numbers on the

second radio’s Duplexers are in the reverse order of the numbers on the first radio’s

Duplexers.

Note: For example, if the numbers on the first radio’s Duplexers are (left to

right) 2/4 and 4/2, the numbers on the second radio’s Duplexers should be

4/2 and 2/4.

Connecting Power over Ethernet

AF11-Complete Quick Start Guide

WARNING: Use only the included adapter, model POE-50-60W. Failure to do

so can damage the unit and void the product warranty.

airFiber Configuration

Access the airFiber Configuration Interface and configure the following settings:

Wireless Mode Configure one radio as the Master and the other as the Slave.

Frequency Setting The TX Frequency and RX Frequency settings must be the

reverse of each other on both the Master and the Slave.

2. Configure the Ethernet adapter on your computer with a static IP address on the

192.168.1.x subnet.

3. Launch your web browser. Type https://192.168.1.20 in the address field and

press enter (PC) or return (Mac).

4. Enter ubnt in the Username and Password fields. Select your Country and

Language. You must agree to the Terms of Use to use the product. Click Login.

5. Click Settings, and then click the Wireless tab.

6. Configure the Basic Wireless Settings:

a. For one radio, select Master as the Wireless Mode. For the other radio, keep

the default, Slave.

b. Enter a name in the Link Name field. This should be the same on both the

Master and the Slave.

c. If needed, change the Channel Bandwidth, Output Power and/or Maximum

Modulation Rate settings.

7. Configure the TX Frequency and RX Frequency.

8. Configure the Wireless Security:

a. Select the Key Type, HEX or ASCII.

b. For the Key field:

HEX Enter 16 bytes (eight, 16-bit hexadecimal digits: 0-9, A-F, or a-f). You

can omit zeroes and use colons, similar to the IPv6 format.

ASCII Enter a combination of alphanumeric characters (0-9, A-Z, or a-z).

9. Click Save Changes.

10. In-Band Management is enabled by default, so each airFiber radio must have a

unique IP Address. (If the airFiber radios use the same IP Address, you may lose

access to the airFiber radios via the DATA ports.) Click the Network tab.

a. For the Management IP Address option:

DHCP Keep the default, DHCP, to use DHCP reservation on your router to

assign a unique IP Address.

Static Change the IP Address, Netmask, and other settings to make them

compatible with your network.

b. Click Save Changes.

11. Disconnect the Ethernet cables from the MGMT and DATA ports on the radio.

Configuration of the radio is complete.

Repeat the instructions in the airFiber Configuration section on the other radio.

For details on the airFiber Configuration Interface, refer to the airFiber AF-11FX User

Guide, available at: ui.com/download/airfiber

Note: One airFiber radio’s TX Frequency is the other radio’s RX

Frequency, and vice versa.

Note: The airFiber Configuration Interface supports IPv6 formats

excluding dotted quad and “::” (double-colon) notation.

AF11-Complete Quick Start Guide

UISP Management

You can manage your device using UISP, which lets you configure, monitor, upgrade,

and back up your devices using a single application. Get started at uisp.ui.com

Hardware Installation

Install a Ground Wire

3. At the installation site, secure the other end of the ground wire to a grounded mast,

pole, tower, or grounding bar.

Mount to the airFiber AF-11G35 Antenna

1. Attach an RF Cable to an RF connector labeled H or V. Then slide the silicone boot

over the RF connector to protect it.

Note: For SISO mode, use the RF connector (H or V) as determined by your

licensing. Keep the other RF connector covered with the included Metal Cap.

If using MIMO mode, remove the cap over the second RF connector (V or H) and

attach an RF Cable. Then slide the silicone boot over the RF connector to protect it.

WARNING: Failure to properly ground your airFiber radio will void your

warranty.

Note: The ground wire should be as short as possible and no longer than one

meter in length.

AF11-Complete Quick Start Guide

Note: Align the dot on the side of the shroud with the arrowhead on the dish

antenna.

Connecting Data

AF11-Complete Quick Start Guide

3. If you are using DC power, connect the other end of the Ethernet cable to your LAN.

Connecting Power

Follow the instructions for the source of power that you are using:

“Power Over Ethernet”

“DC Power”

Power Over Ethernet

WARNING: Use only the included adapter, model POE-50-60W. Failure to do

so can damage the unit and void the product warranty.

DC Power

1. Connect a DC power cable to the Terminal Block. (The +VDC and GND can be

connected to either terminal.)

2. Connect the other end of the DC power cable to a DC power supply that supplies

+50VDC.

WARNING: Applying a negative voltage such as -48VDC will damage the

radio.

3. Connect the DC power supply to its source.

Alignment

Tips

To accurately align the airFiber radios for best performance, you MUST align only

one end of the link at a time.

You may need to use additional hardware to compensate for issues such as the

improper orientation of a mounting pole or significant elevation differences between

airFiber radios.

Establishing a Link

Adjust the positions of the Master and the Slave to establish a link. The following

section features the airFiber X antenna, AF-11G35:

Note: The Master must be aimed first at the Slave because the Slave does not

transmit any RF signal until it detects transmissions from the Master.

1. Master Visually aim the Master at the Slave. To adjust the Master’s position, adjust

the azimuth and the elevation.

Adjust the azimuth:

a. Loosen the four flange nuts on the two pole clamps.

b. Rotate the antenna to point towards the other end of the link.

c. Tighten the four flange nuts on the two pole clamps.

AF11-Complete Quick Start Guide

Andere Handbücher für airFiber AF-11

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti NanoStationM Series Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-FlexHD Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi nanoHD Bedienungsanleitung

Ubiquiti

Ubiquiti UNIFI UAP-AC-IW-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti PBE-M5-620 Bedienungsanleitung

Ubiquiti

Ubiquiti airFiber 24 HD Bedienungsanleitung

Ubiquiti

Ubiquiti Bullet M5 HP Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi XG Bedienungs- und Wartungsanleitung

Ubiquiti

Ubiquiti UBB Bedienungsanleitung

Ubiquiti

Ubiquiti Lite Beam AC LR LBE-5AC-LR Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam ac NBE-5AC-16 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP-AC PRO Bedienungsanleitung

Ubiquiti

Ubiquiti LTU-Lite Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-LR Bedienungsanleitung

Ubiquiti

Ubiquiti PrismStation 5AC Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam AC GENZ Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket5ac PtP Bedienungsanleitung

Ubiquiti

Ubiquiti airFiber AF-5XHD Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Bedienungsanleitung

Ubiquiti

Ubiquiti Bullet AC-IP67 Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-IW Bedienungsanleitung

Ubiquiti

Ubiquiti UF-Nano Bedienungsanleitung

Ubiquiti

Ubiquiti nano station M Bedienungsanleitung

Ubiquiti

Ubiquiti AirCube ACB-AC Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung

Ubiquiti airFiber AF-11 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken