Wali M002XLS Bedienungsanleitung

M002XLS

WARNING

！

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.

SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a

qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may

cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.

Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect

assembly or inappropriate use.

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

Dual Monitor Desk Mount

INSTALLATION MANUAL

1-844-SATTLER (18447288537)

[email protected]

www.walielectric.com

TIPOVER WARNING

● NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.

● USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.

Supplied Parts List

Nut

E (x2) K (x2)

Wire Clip

Allen Key

I (x1)

M4x30 Bolt

G (x8)

M4x12 Bolt

F (x8) H (x8)

M4~M6 SpacerVESA Plate

D (x2)

C-Clamp

B1 (x1)

C-Clamp Brace

B2 (x1)

Grommet Base Plate

B5 (x1)

M10 Hand Knob

B4 (x1)

B3 (x1)

Support Plate

Lower Pole

A1 (x1)

Upper Pole

A2 (x1)

M5x14 Bolt

J1 (x3)

Monitor Arm

C (x2)

M8x12 Bolt

J2 (x2)

Option A : 31.5'' Pole Installation

Loosen the screw on the Lower Pole a1 with Allen key 3mm o . Connect

Lower Pole a1 to Upper Pole and tighten the screw with Allen key

3mm o to fix the two poles.

Pre-Assembly

Option A : Clamp Installation

1. Connect Lower Pole a and C-Clamp Brace c from the bottom using M5x14 Bolt f and tighten with Allen Key 3mm o .

Hand Knob

B3 B1

2. Remove the screw and washer at the top of the M10 Hand Knob and connect the M10 handle , C-clamp B1 and support plate with the screw

and washer that were just removed. Select the preferred height according to your desk thickness. Connect C-Clamp B1 to C-Clamp Brace B2 using M8x12

Bolt J1 , and tighten with Allen Key 5mm I . Rotate the hand knob N clockwise to fasten for stability.

B4 B4 B1 B3

3Put the Wire Clips k and Monitor Arms c through the Upper Pole a , adjust the preferred

height and tighten using Allen Key 5mm o .

7Manually swivel, tilt, and rotate the monitor for the best viewing angle.

6Guide the cable through the Wire Clips and store the Allen Keys o in the Wire Clips k .

Adjust the tilt angle using Allen Key 5mm n .

KIK

45°

Select bolts and spacers (if needed) according to your TV/Monitor. Attach the VESA Plate to the Monitor and tighten with a screwdriver. (Screwdriver not included)

Step 4.1

Select Monitor Screws

Step 4.3a

Flat Back Monitor

Step 4.3b

Curved or Recessed Back Monitor

M4x12 M4x30

Only one screw size fits your Monitor

Step 4.2

Select Spacers( if needed )

Hand thread screws into the

threaded inserts on the back

of your Monitor to determine

which screw (M4x12 orM4x30)

to use.

5Put the assembled TV/Monitor onto the Monitor Arms d and tighten the VESA Plate e with

Nut h for stability.

Notice: Please make sure the security nut is installed before you rotate the monitor.E

Option B : Grommet Base Installation

1. Place Lower Pole a onto Grommet Base Plate m . Connect them from the bottom using M5x14

Bolt J1 and tighten with Allen Key 3mm .

A1 B5

Remove the screw and washer at the top of the M10 Hand Knob N .

If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before

installing the desk mount.

Position the Pole A on the mounting surface and connect the hand knob N through the Support

Plate Q and the grommet hole with the Pole A . Rotate the hand knob N clockwise to fasten for

stability.

Remove the screw and washer at the top of the M10 Hand Knob N .

Mark the position of the hole on your mounting surface. Drill a 3/8"(10mm) diameter hole at the

marked position through the mounting surface.

Position the Pole A on the mounting surface and connect the hand knob N through the Support

Plate Q and the self-drilled hole with the Pole A . Rotate the hand knob N clockwise to fasten

for stability.

2a. Existing Grommet Hole Installation 2b. Self-drilled Grommet Hole Installation

B4A1

B4 A1

B4B3

ø 10mm

(ø ")3/8

Andere Wali Rack & Stand Handbücher

Wali

Wali 011ARM Bedienungsanleitung

Wali

Wali PTT007-B Bedienungsanleitung

Wali

Wali GSMP001 Bedienungsanleitung

Wali

Wali STT001D-B Bedienungsanleitung

Wali

Wali GPV001 Bedienungsanleitung

Wali

Wali WL-TTM-1 Bedienungsanleitung

Wali

Wali M002XLS Bedienungsanleitung

Wali

Wali MATI001-G Bedienungsanleitung

Wali

Wali M001XLLP Bedienungsanleitung

Wali

Wali WL-M002 Bedienungsanleitung

Wali

Wali M12XXL Bedienungsanleitung

Wali

Wali PRS001 Bedienungsanleitung

Wali

Wali GSDM002 Bedienungsanleitung

Wali

Wali SWM-EH-01B Bedienungsanleitung

Wali

Wali MF002 Bedienungsanleitung

Wali

Wali M001SXL Bedienungsanleitung

Wali

Wali TVDVD-04 Bedienungsanleitung

Wali

Wali MF003S Bedienungsanleitung

Wali

Wali TVDVD-5 Bedienungsanleitung

Wali

Wali TVF001XL Bedienungsanleitung

Wali

Wali GSDM003 Bedienungsanleitung

Wali

Wali SBR201 Bedienungsanleitung

Wali

Wali M001-W Bedienungsanleitung

Wali

Wali SON002-B Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung