Wasp WWS500 Betriebsanleitung
Wasp Barcode Technologies
1400 10th Street
Plano, TX 75074
www.waspbarcode.com 1007US
WWS500 Programming Guide
Barcode Scanning Made Easy
Table of Contents
Chapter 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Chapter 2. Barcode Symbologies . . . . . . . . . . . . . . . . . . .3
Chapter 3. Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Chapter 4. WWS500 Setup & Configuration . . . . . . . .6-28
1. Setup & Configuration . . . . . . . . . . . . . . . . .6
2. Factory Default & Autosense Stand Mode . .7
3. Beep and Delay . . . . . . . . . . . . . . . . . . . .8-9
4. Upper/Lower Case . . . . . . . . . . . . . . . . . . .10
5. Keyboard Language . . . . . . . . . . . . . . . . . .11
6. Preamble/Postamble Configuration . . . . . .12
7. Terminator/Code ID . . . . . . . . . . . . . . . . . .13
8.
Enable/Disable Barcode Symbologies
. . .14-15
9. Barcode Symbology Settings . . . . . . . .16-28
Code 39 . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Interleaved 2 of 5 and Code 93 . . . . . . . . .17
Code 128 and UCC/EAN 128 . . . . . . . . . . .18
MSI/Plessey . . . . . . . . . . . . . . . . . . . . . . .19
Codabar . . . . . . . . . . . . . . . . . . . . . . . . . . .20
UPC-A . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
UPC-A Supplemental / UPC-A to EAN-13 .22
UPC-E . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
UPC-E Supplemental . . . . . . . . . . . . . . . . .24
EAN-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
EAN-8 Supplemental . . . . . . . . . . . . . . . . .26
EAN-13 . . . . . . . . . . . . . . . . . . . . . . . . . . .27
EAN-13 Supplemental . . . . . . . . . . . . . . . .28
Chapter 5. Bluetooth Settings . . . . . . . . . . . . . . . . . . . . .29
Appendix A Barcode Test Symbols . . . . . . . . . . . . . . .30-32
Appendix B ASCII Table . . . . . . . . . . . . . . . . . . . . . . . .33-36
Appendix C Codes for PC . . . . . . . . . . . . . . . . . . . . . . . . .37
Appendix D Technical Specifications . . . . . . . . . . . . . . . . .38
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
FAQ / Product Support . . . . . . . . . . . . . . . . .40
Chapter 1
2
Introduction
Barcoding is the most common Automated Data Collection (ADC)
technology providing timely, error-free information that can be used to
increase productivity, accuracy, and efficiency in the workplace. Virtually
every type of industry is using bar codes to replace keyboard data entry.
Studies have shown that a proficient data entry operator will make one
error for every 300 characters that are manually entered. The error rate
using barcodes is almost negligible and can be error-free using barcode
symbologies with the check digit enabled.
The Wasp Charged Coupled Device (CCD) technology is a technique
whereby a barcode is photographed, digitized, and electronically sampled
by built-in photodetectors. The detectors process the measurement of
every bar and space using the number of adjacent photodetectors which
contrast a black mark and a white space. The Wasp WWS500 Freedom
Scanner is extremely rugged since it has no moving parts.
Of all the hand held barcode scanning devices on the market, the CCD
reader is the easiest to use and most cost effective for the typical business
user. The Wasp WWS500 Freedom Scanner is an extended distance
scanner with a depth of reading of up to one foot depending on the mil
size of the barcode. To activate the scanner, the user simply points the
scanning aperture towards the barcode, pulls the trigger, and aims the red
LED beam across the barcode.
Chapter 2
3
Barcodes are symbols consisting of a series of bars and spaces which can
be applied to packages, cartons, bottles, and other commercial products.
The bars and spaces in each symbol are grouped in such a way to
represent a specific ASCII character or function. The interpretation of
these groups is based on a particular set of rules called symbologies.
Various symbologies have been developed for particular applications.
Some examples are shipping and receiving, manufacturing, retail,
healthcare, transportation, document processing and tracking, and
libraries.
The resolution of a barcode is dependent on the narrowest element of a
barcode (X dimension), and can vary from high density (nominally less
than 0.009 in./0.23 mm), medium density (between 0.009 in./0.23 mm and
0.020 in./0.50 mm), and low density (greater than 0.020 in./0.50 mm).
Medium and low densities are the most common since these are the
easiest to read (scan) with nearly all scanning devices. The Wasp
WWS500 Freedom Scanner can read barcodes with X-dimensions as low
as 5 mils (0.005 in/0.13mm).
The Wasp WWS500 Freedom Scanner can read the most popular barcode
symbologies including Code 39, Code 93, Code 128, Interleaved 2 of 5,
UPC-A, UPC-E, EAN/JAN-8, EAN/JAN-13, Codabar, and MSI/Plessey.
Please see test chart on pages 28-30.
Barcode Symbologies
Chapter 3
4
Quick Start
1. Unpack
Open the box and remove all the pieces from their protective packaging.
2. Charging the WWS500
You must charge the scanner for 4 hours before first using it. To charge
the scanner plug the power supply in to the bottom of the scanner.
3. Setting up the Bluetooth Adaptor
If you already have Bluetooth setup on your PC or device, please
continue to the next step.
To setup Bluetooth on your PC you will need to insert the Bluetooth
adapter into an available USB port. Windows will detect the adapter and
install the required Microsoft Bluetooth software. If Windows does not
detect the Bluetooth adapter, please remove the adapter and insert the CD
with the adapter’s Bluetooth software on it. Follow the instruction on the
CD for installing the Bluetooth software.
4. Connecting the scanner to a Bluetooth device.
The scanner will connect to most Bluetooth devices that support HID
connection.
You will need to open your Bluetooth software and search for Bluetooth
devices. The Bluetooth software can be found by clicking the Bluetooth
symbol on the start bar near the computer time. If the Bluetooth symbol is
not found, there could be a problem with the Bluetooth adapter installation.
Once you have the Bluetooth software open
you will need to scan the Set Connection
barcode (right). This will make the scanner ready
to be detected by the Bluetooth software. Set Connection
Chapter 3
5
The following screens are Microsoft’s standard Bluetooth wizard.
*Most Bluetooth wizards will have similar steps.
Check the “My device is setup and
ready to be found.” and click Next.
The scanner will show up in the list of
Bluetooth devices found. Select the
WASP_HID and click Next.
* If WASP_HID does not show up in the
available devices please check the following.
- Make sure the scanner is on by pressing
the trigger.
- If you are using a pre-installed Bluetooth
adapter, make sure the adapter supports HID.
The next step will ask you to setup a passkey
for the device. By default the scanner will not
have a passkey set. Please select “Don’t use
a passkey” and click Next.
The last screen of the wizard will be complete
the wizard. Just click Finish to complete.
Once the wizard is complete the scanner will
show up as a WASP_HID Device. Click OK to
close the screen. You are now ready to use
the WWS500.
Chapter 4
6
In order to configure Wasp WWS500 Freedom Scanner, you must
familiarize yourself with the setup procedures on the following pages. The
default settings of the scanners are identified on each page and clearly
marked using an asterisk (*). The default settings have been
preprogrammed for the most common barcode configurations.
Use the setup & configuration barcodes only to customize the
WWS500 Freedom Scanner settings. If you need to configure the
Scanner, the default settings will be overwritten. All the programmed
settings are stored permanently in non-volatile memory.
In order to configure Wasp WWS500 Freedom Scanner,
two basic steps need to be followed:
(1) Locate the group that contains the options to be changed.
(2) Scan the barcode representing the option to be changed.
The scanner will sound two beeps.
To change Minimum/Maximum Length:
(1) Scan the Minimum or Maximum Length barcode on page 15.
(2) Scan a 2 digit value from the ASCII table on pages 31-34
(3) Scan the Minimum or Maximum Length barcode again.
Example: To have a minimum length barcode of 1, you must scan a
0 then 1, then scan the minimum barcode again. To have a maximum
length barcode of 10, you must scan a 1 then 0, then scan the
maximum barcode again.
Setup & Configuration
Chapter 4
7
FACTORY DEFAULT & KEYBOARD CONNECTION
Use the Factory Default barcode to reset the scanner to the Default settings.
Factory Default
Autosense Flash Mode Enable
Scan this Autosense Stand Mode bar code to enable the hands-free autosense
feature of the WWS500 Freedom Scanner. If you desire to turn this mode “off,”
please scan the default bar code above.
Autosense Stand Mode
Factory Default
Note: Enabling this option will significantly increase the WWS500
Freedom Scanners battery consumption.
Chapter 4
8
BEEP AND DELAY
The 'Beep and Delay' configuration supports the general control options for the
Wasp WWS500 Freedom Scanner. These options include the volume,
intercharacter delay, and interblock delay.
Interblock delay is the minimum time interval between two adjacent scans. If the
processing speed of your host device is slower than your scanning speed, a longer
interblock delay may ensure the data integrity.
Intercharacter delay is the time period that the scanner will wait before transmitting
the next character. If data sent by the scanner has incorrect or missing characters,
a longer intercharacter delay may solve the problem. The intercharacter delay
should be changed only if the transfer rate cannot be maintained between the
scanner and the keyboard buffer of the computer.
Note: The default for the intercharacter delay is set to '140us' and is the most
common configuration; however, your PC may be different. When you scan a bar
code, if some stray or scrambled characters appear, increase the intercharacter
delay to slow down the transfer rate.
Beep Off
Beep Medium *
Beep High to Low
Beep Hi
Beep Low to High
Beep Low
Beep Settings
*Default
Chapter 4
9
BEEP AND DELAY
0ms *
10ms
50ms
100ms
200ms
140us *
500us
1ms
4ms
16ms
500ms
Interblock Delay Intercharacter Delay
*Default
Andere Handbücher für WWS500
1
Inhaltsverzeichnis
Andere Wasp Barcode-Lesegerät Handbücher
Wasp
Wasp WPL205 Bedienungsanleitung
Wasp
Wasp Wasp WDI7500 Bedienungsanleitung
Wasp
Wasp WDI4600 Bedienungsanleitung
Wasp
Wasp WPL25 Bedienungsanleitung
Wasp
Wasp WWS550i Installationsanleitung
Wasp
Wasp WLP 4170 Betriebsanleitung
Wasp
Wasp WPL610 Bedienungsanleitung
Wasp
Wasp Bar Code Laser Betriebsanleitung
Wasp
Wasp WLP 4170 CCD Betriebsanleitung
Wasp
Wasp WLS8600 Bedienungsanleitung
Wasp
Wasp WWS800 Bedienungsanleitung
Wasp
Wasp WWS550SBR Bedienungsanleitung
Wasp
Wasp WPL305 Betriebsanleitung
Wasp
Wasp WDI4700 Bedienungsanleitung
Wasp
Wasp WPS1500 Bedienungsanleitung
Wasp
Wasp WWS650 Installations- und Betriebshandbuch
Wasp
Wasp WWS800 Handbuch
Wasp
Wasp HC1 Bedienungsanleitung
Wasp
Wasp WWS800 Bedienungsanleitung
Wasp
Wasp WWS150i Bedienungsanleitung
Beliebte Barcode-Lesegerät Handbücher anderer Marken
POSMicro
POSMicro Datalogic PowerScan D7100 Bedienungsanleitung
Marson
Marson MT780 Kurzanleitung zur Einrichtung
NCR
NCR RealPOS Bedienungsanleitung
Motorola
Motorola SE3300 Kurzanleitung zur Einrichtung
Element
Element P130BT Bedienungsanleitung
Motorola
Motorola Symbol LS3008 Installations- und Betriebshandbuch
