Whalen Z BEAM WSZB1848-5BW-2 Bedienungsanleitung

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.

PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Date: 2017-01-20 Rev. 2

Whalen Furniture Manufacturing Factory # HAIOFF

Page 1 of 7

ITM./ART. 420424&420825

MODEL# WSZB1848-5BW-2&WS1848ZL

Assembly Instructions

Visit our website www.whalenstorage.com

1. Please read instructions prior to assembly.

2. Verify that there are no missing parts.

3. Keep instructions for future reference.

4. Recommend to use 2 people for assembly.

5. Gently set parts on a flat, smooth surface.

6. For indoor use.

Page 2 of 7

Parts List

Please read completely through the instructions and verify that all parts listed are present before beginning assembly.

PART# PART DESCRIPTION QUANTITY

A- Angle Post

B- Long Z-beam 10

C- Short Z-beam

D- Shelf Deck

E- Post Cap 8

F- Post Insert

G- Post Clip 2

Page 3 of 7

ATTENTION

Storage Rack is not recommended for outdoor use.

1. Use some type of lubricant to ease the joining of the angle posts and beams.

2. Use a cloth or wood block to protect the surface finish of the product when using a hammer.

3. Rivets must seat at the bottom of the keyhole slot. Hit the flat section of Z beam.

4. Assemble the unit on a sturdy and level surface. Avoid assembly on carpet.

5. Load small stable items on the top shelves, heavier and bulkier items should be stored on the lower shelves.

OPTION #1 STORAGE RACK

Note: To facilitate assembly we recommend having two persons assemble the unit. If you do not

understand these directions, or have any doubts about the safety of the installation, please call a

qualified contractor. We can assist you or give you directions, if you have any defective parts please

do not use, improper installation may result on damage or injury.

Assembly Steps

Start the End Assembly by joining a Short Z-beam (part

C) into the two bottom keyholes of an Angle Post (part

A). Install the Z-beam in the upright position, as shown

in the illustration. Drive the rivets to the bottom of the

keyhole by hitting the beam near the joint with a rubber

mallet to lock the pieces together.

Repeat last step to the second Angle Post (part A)

creating an End Assembly.

Assemble a Long Z-beam (part B) to the other two

bottom keyholes of the End Assembly. Assure all Z-

beams are assembled in the upright position. As shown

in the illustration. Hit the beam near the joint with a

rubber mallet to lock pieces together.

Note: Don’t hit too hard so you will not damage or

bend the beams.

Repeat last step to add an additional Long Z-beam, the

other Short Z-beam and two Angle Posts to the End

Assembly to create the Bottom Frame Assembly.

Note: Follow the order 1st through 5th as shown in

the illustration to facilitate the assembly. Hit the

beams near the joints to lock the pieces into place.

Page 4 of 7

Now pick up a Short Z-beam (part C) and join into the

top two keyholes of the other 2 Angle Post (part A) to

create a Top End Assembly. Drive the rivets to the

bottom of the keyhole with a rubber mallet. Make sure

the flat edge of the Z-beam point up.

Repeat last step for the opposite side Top End

Assembly.

Before joining the Top End Assembly to the Bottom

Frame Assembly insert Post Inserts (part F) into the

Angle Posts (part A) on the Bottom Frame Assembly.

Proceed to assemble the Top End Assembly on to the

Post Insert (part F) as shown in the illustration.

Repeat last 2 step for the opposite Top End Assembly.

Add a Short Z-beam (part C) to mid section at the joint

by inserting the top rivet of the Z-beam into the bottom

keyhole of the Top End Assembly, and the bottom rivet

of the Z-beam into the top keyhole of the Bottom Frame

Assembly. Make sure all Z-beams in the upright position.

Drive the rivets to the bottom of the keyholes by hitting

the beam near the joints to lock pieces together.

Repeat last step to add an additional Short Z-beam

(part C) and two Long Z-beams (part B).

Proceed to add two additional Long Z-beams (part B) to

top two keyholes of the Angle Posts (part A) as shown in

the illustration. Install the Z-beams in the upright

position. Assure to have the rivets in the keyholes before

hitting the beams near the joints to lock the pieces

together.

Page 5 of 7

Assemble the remaining Long and Short Z-beams (part B

and C) to your desired location on the Angle Posts (part

A) to create two additional shelves as shown in the

illustration. Assure to install the Z-beams in the upright

position. Hit the beams near the joints to lock pieces

together.

Note: The posts are adjustable in 1-1/2" increment.

You can adjust the shelves at your desired height.

Now lay the Shelf Decks (part D) in between the Z-beams.

Insert the Post Caps (part E) on the top of the Angle Posts

(part A) as shown in the illustration.

Repeat step 1 and 2 to create a Bottom Frame Assembly.

Now insert two Short Z-beams and two Long Z-beams

(part C and B) to the top keyholes of the Angle Posts. Hit

the beams near the joints with a rubber mallet to lock

pieces together. As shown in the illustration.

Add two additional Short Z-beams and two Long Z-beams

(part C and B) to create a shelf at your desired level.

Assure all Z-beams are assembled in the upright position.

Now start the Add-On Unit by joining the first Short Z-

beam (part C) into the top two keyholes of the other two

Angle Posts (part A). The second Short Z-beam must be

assembled at the 7th and 8th keyholes from the bottom of

the Angle Posts. As shown in the illustration. Hit the beam

near the joints with a rubber mallet to lock pieces together.

Repeat for the opposite end assembly.

Z-beam

Shelf Deck

7th and 8th

keyhole

Page 6 of 7

Complete the Add-On Unit by adding two Long Z-beams

(part B) at the top keyholes of the Angle Posts (part A) and

inserting two Long Z-beams (part B) into the 7th and 8th

keyholes from the bottom of the Angle Posts. As shown in

the illustration. Install all Z-beams in the upright position.

Hit the beams near the joint with a rubber mallet to lock

joints into place.

Now lay the Shelf Decks (part D) in between the Z-beams as

shown.

To secure the frames together align the four middle

Angle Posts (part A) of the frames as shown. Start with

the two back middle Angle Posts. Align the indents on

the Post Clips (part G) with two keyholes of the back

middle Angle Posts. Firmly clamp together a Post Clip

and the two angle posts. Repeat the step to clamp the two

front middle angle posts.

Note: To remove Post Clips use a screwdriver.

Insert the Post Caps (part E) on the top of the Angle Posts

(part A) as shown.

Periodically inspect the unit to ensure all Z-beams are seated

properly and firmly connected to the Angle Posts.

Shelf Deck

Upright

Position

(Z-beam)

Page 7 of 7

Care and Maintenance

 Use a soft, clean cloth that will not scratch the surface when dusting.

 Use of furniture polishes is not necessary. Should you choose to use polishes, test first in an inconspicuous area.

 Using solvents of any kind on your furniture may damage your furniture’s finish.

 Never use water to clean your furniture as it may cause damage to the finish.

 Stains or marks from crayons or ink markers will be difficult to remove.

 Do not use any harsh abrasives or chemicals to clean any metal surfaces as it may damage the protective

coating.

 Metal will rust if the finish is scratched or if your furniture is exposed to excessive humidity, particularly

in salt water locations.

 Most metal furniture has a protective coating to prevent rust, however rust may occur if the finish is

marred or wears away over time.

 In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a

professional to repair your furniture.

 Check beam rivets periodically and tighten them if necessary.

Made in China ○

IF YOU ARE REQUIRED TO ORDER PARTS PLEASE USE THE LIST BELOW

1*WSZB1848-5BW-2-1-AP Angle Post

2*WSZB1848-5BW-2-2-LZB Long Z-beam

3*WSZB1848-5BW-2-3-SZB Short Z-beam

4*WSZB1848-5BW-2-4-SD Shelf Deck

5*WSZB1848-5BW-2-5-PC Post Cap

6*WSZB1848-5BW-2-6-PI Post Insert

7*WSZB1848-5BW-2-7-PC Post Clip

*WSZB1848-5BW-2-8-CH Complete Hardware

1*WS1848ZL-1-AP Angle Post

2*WS1848ZL-2-LZB Long Z-beam

3*WS1848ZL-3-SZB Short Z-beam

4*WS1848ZL-4-SD Shelf Deck

5*WS1848ZL-5-PC Post Cap

6*WS1848ZL-6-PI Post Insert

7*WS1848ZL-7-PC Post Clip

*WS1848ZL-8-CH Complete Hardware

420825_WS1848ZL_Z-Beam 5 Shelf Unit/Silver Vein Frame

420424_WSZB1848-5BW-2_Z-Beam 5 Shelf Unit/Black Wrinkle Frame

ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.

POR FAVOR LEA Y CONSERVAR PARA FUTURA REFERENCIA.

Fecha: 2017-01-20 Rev. 2

Whalen Furniture Manufacturing Fábrica # HAIOFF

Página 1 de 7

ARTÍCULO 420424&420825

MODELO# WSZB1848-5BW-2&WS1848ZL

Instrucciones de Ensamble

Visite nuestro sitio web www.whalenstorage.com

1. Por favor, lea las instrucciones antes del

montaje.

2. Compruebe que no hay partes que faltan.

3. Mantenga las instrucciones para referencia

futura.

4. Recomendamos el uso de 2 personas para el

montaje.

5. Con cuidado de partes del juego sobre una

superficie plana y lisa

6. Para uso en interiores.

Página 2 de 7

Lista de Partes

Por favor lea completamente a través de las instrucciones y compruebe que todas las partes que figuran están presentes

antes de comenzar el montaje.

PARTE # DESCRIPCIÓN DE PARTES CANT.

A- Poste Angular

B- Poste-Z Largo

C- Poste-Z Corto

D- Entrepaño

E- Tapa para Poste

F- Inserto para Poste

G- Seguro para Poste

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Whalen Inneneinrichtung Handbücher

Whalen

Whalen Bayside FURNISHINGS CUKGLBST-3G Bedienungsanleitung

Whalen

Whalen Legeant Hutch Bedienungsanleitung

Whalen

Whalen CSC7PCHD-3VN Bedienungsanleitung

Whalen

Whalen Bayside FURNISHINGS 369333 Bedienungsanleitung

Whalen

Whalen WSUC-4C Bedienungsanleitung

Whalen

Whalen SFKCWMS Bedienungsanleitung

Whalen

Whalen Trimble Bookcase ECOM-TR30BK Bedienungsanleitung

Whalen

Whalen AVC-22E Bedienungsanleitung

Whalen

Whalen Stetson SMSSDSK Betriebsanleitung

Whalen

Whalen LEVELUP SPLS-LTCGD Bedienungsanleitung

Whalen

Whalen TGXLD-1 Bedienungsanleitung

Whalen

Whalen Bayside CSC7PD-5 Bedienungsanleitung

Whalen

Whalen WS-NIR-722484-5S Bedienungsanleitung

Whalen

Whalen WSF54BF23-3 Bedienungsanleitung

Whalen

Whalen The Pioneer Woman PWS336158813017 Bedienungsanleitung

Whalen

Whalen 19WTLD-SPCA Bedienungsanleitung

Whalen

Whalen BBHC60DBC Bedienungsanleitung

Whalen

Whalen BBLAVC54T Bedienungsanleitung

Whalen

Whalen Breenly SPUS-BRMF-WH Bedienungsanleitung

Whalen

Whalen WMCXL-2 Bedienungsanleitung

Whalen

Whalen Bayside 126678 Bedienungsanleitung

Whalen

Whalen Santa Fe Writing Desk Bedienungsanleitung

Whalen

Whalen JCS110605-D Bedienungsanleitung

Whalen

Whalen Bayside CSC3N1C-72-5 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung