Zeiss Fluar Illuminator Z mot. Bedienungsanleitung

Operating Manual

Fluar Illuminator Z mot.

for Axio Zoom.V16

You have purchased a high quality product from Zeiss. Before using

the instrument the first time, please read this operating manual in

order to maintain the high quality of the instrument and ensure

reliable work with it for a long time.

Carl Zeiss Fluar Illuminator Z mot.

4 435180-9060-701 05/2012

Knowledge of this manual is required for the operation of the device. You should therefore familiarize

yourself with the contents of this manual and pay special attention to instructions concerning the safe

operation of the instrument.

We reserve the right to make changes in the interest of technological advancement; the operating

manual is not subject to updating or revision.

exploitation or communication of its contents are not permitted. Persons in contravention of this

Published by: Carl Zeiss Microscopy GmbH

Carl-Zeiss-Promenade 10

07745 Jena, Germany

microscop[email protected]m

www.zeiss.com/microscopy

Carl Zeiss Microscopy GmbH

Königsallee 9-21

37081 Göttingen, Germany

SAP number: 435180-9060-701

Date of issue (Version 5): 01 May 2012

CONTENTS

Fluar Illuminator Z mot. Carl Zeiss

05/2012 435180-9060-701 5

CONTENTS

Page

1INTRODUCTION ........................................................................................................... 6

1.1 General information....................................................................................................... 6

1.2 Notes on instrument safety ............................................................................................ 7

1.3 Notes on warranty ......................................................................................................... 9

2DESCRIPTION ............................................................................................................. 10

2.1 Indication for use ......................................................................................................... 10

2.2 Package check list with accessories............................................................................... 11

2.3 Microscope systems ..................................................................................................... 12

2.4 Technical data.............................................................................................................. 12

3SET-UP ....................................................................................................................... 13

3.1 General information..................................................................................................... 13

3.2 Assemble the Fluar Illuminator Z mot. and connect it up ............................................... 13

3.3 Connecting the HXP 200 C illuminator ......................................................................... 14

3.4 Loading the reflector turret .......................................................................................... 15

3.5 Inserting or removing the stop slider............................................................................. 16

3.6 Connecting the Fluar Illuminator Z mot......................................................................... 17

4OPERATION ............................................................................................................... 18

4.1 Control elements on the Fluar Illuminator Z mot. .......................................................... 18

4.2 Control elements on the HXP 200 C illuminator............................................................ 18

4.3 Switching on and adjusting the Fluar Illuminator Z mot. ................................................ 19

4.4 Switching off the Fluar Illuminator Z mot. ..................................................................... 20

4.5 Wearing parts .............................................................................................................. 21

4.6 Troubleshooting........................................................................................................... 21

INTRODUCTION

Carl Zeiss General information Fluar Illuminator Z mot.

6 435180-9060-701 05/2012

1INTRODUCTION

1.1 General information

Fluar Illuminator Z mot. and the Axio Zoom.V16 microscope have been designed, manufactured and

tested in compliance with DIN EN 61010-1 (IEC 61010-1) and IEC 61010-2-101 Safety requirements for

electrical equipment for measurement, control and laboratory use.

The Fluar Illuminator Z mot. and Axio Zoom.V16 zoom microscope meet the requirements of EC Directive

IvDD 98/79/EC (In vitro diagnostic medical devices); they are marked with the mark.

The operating manual contains all information and warnings the operator must comply with.

The following warning and information symbols are used in this operating manual:

CAUTION

This symbol indicates a potential hazard to the user.

CAUTION

Optical radiation is emitted. Do not look into the laser beam!

This may be harmful to the eyes (see Section 2.3).

CAUTION

Risk of pinching!

CAUTION

Hot surface!

CAUTION: High-energy UV radiation!

Risk of injury to eyes and skin!

CAUTION

Disconnect the instrument from the power supply before opening!

ATTENTION

This symbol indicates a potential hazard to the instrument or system.

NOTE

This symbol indicates an instruction which requires particular attention.

INTRODUCTION

Fluar Illuminator Z mot. Notes on instrument safety Carl Zeiss

05/2012 435180-9060-701 7

1.2 Notes on instrument safety

Fluar Illuminator Z mot. may only be used for the applications described in this operating

manual. The manufacturer cannot assume any liability for other applications of the instrument,

including those of individual modules or single parts.

Modifications and repairs to this instrument and any devices operated in combination with the

microscop

e must be carried out by our service department or by authorized personnel only. The

manufacturer accepts no liability for damage

caused by unauthorized access to the interior of

the instrument. Failure to comply with this shall also render any warranty claims invalid.

The device may only be operated by instructed personnel. The instruments may only be

operated by trained personnel who are aware of the possible dangers involved with microscopy

and the application concerned. The microscope is a high-pre

cision instrument whose

performance may be impaired if handled improperly.

The separate manufacturer's instructions must be observed and general safety requirements

complied with when connecting and operating the HXP 200 C illuminator.

The HXP 200 C generates high-

energy light with an invisible portion. Risk of dazzling or

blinding! Never look directly into the light beam or light guide exit.

The lamp used in the HXP 200 C becomes very hot during operation and has a high internal

pressure in a heated state. Risk of fire or explosion!

The lamp must be changed in accordance with the manufacturer's instructions.

The illuminator may only be connected to a properly installed earthed power outlet.

The mains plug of instruments with a metal housing (e.g. HXP 200 C) may only be connected

to a socket with earth contact. The protective capacity must not be rendered ineffective by

using an extension cable without a ground wire.

If it is determined that protective measures are no longer effective, the instrument must be

switched off and secured against inadvertent operation. Please contact a Zeiss service agency or

the Carl Zeiss Microscopy Service to repair the instrument.

Dust and dirt may impair the instrument’s performance. The instrument must be effectively

protected from such influences and covered with the dust cover when not in use. Always check

whether the instrument is switched off before you cover it. Broad temperature fluctuations,

direct sunlight and vibrations should be avoided.

The instruments are not equipped with special devices to protect against corrosive, potentially

infectious, toxic, radioactive or other substances that may be hazardous to health. All legal

regulations must be observed when handling such substances, particular

ly the relevant national

accident prevention regulations.

INTRODUCTION

Carl Zeiss Notes on instrument safety Fluar Illuminator Z mot.

8 435180-9060-701 05/2012

On microscopes with motorized focusing drive there is a risk of pinching fingers in the work

area when lowering the body of the microscope.

−Before switching on check that the joystick on the SYCOP 3 is at the zero position and not

swiveled out, and that the foot pedal is clear.

−

Automatic travel can be interrupted by pressing the STOP button on the focusing drive or

the STOP button on the SYCOP 3, moving the joystick on the SYCOP 3 up and down,

turning the knurled wheel on the HIP or pressing the Memory 1 or 2 keys on the HIP.

−Do not reach into the possible travel path of the motorized table. There is a risk of pinching

or injury to the fingers when the table is positioned by the control unit.

Defective instruments are not to be disposed of as ordinary domestic waste. They should be

disposed of in accordance with the relevant regulations.

Samples should also be disposed of in compliance with the relevant legal requirements and

internal operating procedures.

The separate operating manuals for the Axio Zoom.V16, HXP 200 C and SYCOP 3 (if used)

must be observed and the general safety requirements complied with.

−Operating Manual Axio Zoom.V16: Order No. 435080-9030-701, English edition

−Operating Manual SYCOP 3: Order No. 435611-9010-701, English edition

−Operating Manual HXP 200 C

Fig. 1 Warning signs on the Axio Zoom.V16 microscope system with Fluar Illuminator Z mot. and

HXP 200 C illuminator

INTRODUCTION

Fluar Illuminator Z mot. Notes on warranty Carl Zeiss

05/2012 435180-9060-701 9

1.3 Notes on warranty

The manufacturer guarantees that the instrument is free of material or manufacturing defects when

delivered. Possible defects must be notified to us immediately and steps taken to minimize damage. If

notified of such a defect, the manufacturer is obligated to rectify it at his discretion, either by repairing

the instrument or delivering an intact replacement. No guarantee is provided for defects caused by

natural wear (wearing parts in particular) and improper use.

The instrument manufacturer shall not be liable for damage caused by faulty operation, negligence or

any other tampering with the instrument, particularly the removal or replacement of instrument

components, or the use of accessories from other manufacturers. Such actions will render any warranty

claims invalid.

With the exception of the work described in this operating manual, no maintenance or repair work is to

be carried out on these microscopes. Repairs may only be performed by Carl Zeiss service staff or

personnel specifically authorized by Carl Zeiss. In the event of a problem with the instrument, please

contact the Carl Zeiss microscopy service team or your local Carl Zeiss overseas representative.

DESCRIPTION

Carl Zeiss Indication for use Fluar Illuminator Z mot.

10 435180-9060-701 05/2012

2DESCRIPTION

2.1 Indication for use

In conjunction with the HXP 200 C illuminator and filter modules the Fluar Illuminator Z mot. is used to

excite fluorescence in specimens.

The Fluar Illuminator Z mot. is designed exclusively for operation with the Axio Zoom.V16 microscope.

The HXP 200 C illuminator generates extremely high-energy light in the visible and invisible range. The

related safety precautions and instructions for use must be strictly observed (see separate operating

manual).

When operating the microscope always use the anti-glare shield to avoid eye damage due to scattered

light.

The cover on the reflector turret of the Fluar Illuminator Z mot. is provided with safety contacts which

interrupt the beam path to the HXP 200 C when the cover is removed, in order to prevent glare and eye

damage.

The Fluar Illuminator Z mot. cannot be used on the coarse/fine drive with T-column 350 mm.

When operating the Fluar Illuminator Z mot. the separate operating manuals for the Axio Zoom.V16

microscope, HXP 200 C illuminator and SYCOP 3 system control panel (if used) must always be observed.

Inhaltsverzeichnis

Andere Zeiss Mikroskop Handbücher

Zeiss

Zeiss Lightsheet Z.1 Bedienungsanleitung

Zeiss

Zeiss SIGMA Series Bedienungsanleitung

Zeiss

Zeiss Axiovert 200 Bedienungsanleitung

Zeiss

Zeiss Axio Imager 2 Bedienungsanleitung

Zeiss

Zeiss ELYRA Bedienungsanleitung

Zeiss

Zeiss OPMI PROergo S7 Bedienungsanleitung

Zeiss

Zeiss LSM 900 Bedienungsanleitung

Zeiss

Zeiss Axiocam MR Installations- und Betriebsanleitung

Zeiss

Zeiss SL 800 Bedienerhandbuch

Zeiss

Zeiss Axiolab 5 Bedienungsanleitung

Zeiss

Zeiss LSM800-6 Bedienungsanleitung

Zeiss

Zeiss Axiolab 5 Bedienungsanleitung

Zeiss

Zeiss LSM 880 Bedienungsanleitung

Zeiss

Zeiss Mechanical stage S mot. Bedienungsanleitung

Zeiss

Zeiss Stemi 305 Bedienungsanleitung

Zeiss

Zeiss SV 6 Bedienungsanleitung

Zeiss

Zeiss Axioscope 5 Bedienungsanleitung

Zeiss

Zeiss LSM 880 Bedienungsanleitung

Zeiss

Zeiss AxioObserver D1 Bedienungsanleitung

Zeiss

Zeiss Axioskop 40 Bedienungsanleitung

Zeiss

Zeiss Axiostar plus Bedienungsanleitung

Zeiss

Zeiss Smartzoom 5 Bedienungsanleitung

Zeiss

Zeiss LSM 710 Bedienungsanleitung

Zeiss

Zeiss EXTARO 300 Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Olympus

Olympus SZ61 Bedienungsanleitung

Leica

Leica FL560 Bedienungsanleitung