Zeiss Transillumination top 450 mot. Bedienungsanleitung

Operating Manual

Transillumination top 450 mot.

for Axio Zoom.V16

You have purchased a high quality product from Zeiss. Before using

the instrument the first time, please read this operating manual in

order to maintain the high quality of the instrument and ensure

reliable work with it for a long time.

Carl Zeiss Transillumination top 450 mot.

4 435500-9000-701 08/2012

Knowledge of this manual is required for the operation of the device. You should therefore familiarize

yourself with the contents of this manual and pay special attention to instructions concerning the safe

operation of the instrument.

We reserve the right to make changes in the interest of technological advancement; the operating

manual is not subject to updating or revision.

exploitation or communication of its contents are not permitted. Persons in contravention of this

Published by: Carl Zeiss Microscopy GmbH

Carl-Zeiss-Promenade 10

07745 Jena, Germany

microscop[email protected]m

www.zeiss.com/microscopy

Carl Zeiss Microscopy GmbH

Königsallee 9-21

37081 Göttingen, Germany

SAP number: 435500-9000-701

Date of issue (Version 3): 08/07/2012

CONTENTS

Transillumination top 450 mot. Carl Zeiss

08/2012 435500-9000-701 5

CONTENTS

Page

1INTRODUCTION ........................................................................................................... 6

1.1 General information....................................................................................................... 6

1.2 Notes on instrument safety ............................................................................................ 7

1.3 Notes on warranty ......................................................................................................... 8

2DESCRIPTION ............................................................................................................... 9

2.1 Indication for use ........................................................................................................... 9

2.2 Package check list with accessories................................................................................. 9

2.3 Microscope system with transillumination top 450 mot. ................................................ 10

2.4 Technical data.............................................................................................................. 11

3SET-UP ....................................................................................................................... 12

3.1 General information..................................................................................................... 12

3.2 Mounting the transillumination top 450 mot. ............................................................... 12

3.3 Connecting the transillumination top 450 mot.............................................................. 14

4OPERATION ............................................................................................................... 15

4.1 Control elements ......................................................................................................... 15

4.2 Switching on ............................................................................................................... 17

4.3 Switching off ............................................................................................................... 17

4.4 Troubleshooting........................................................................................................... 18

4.5 Functional limitations ................................................................................................... 18

INTRODUCTION

Carl Zeiss General information Transillumination top 450 mot.

6 435500-9000-701 08/2012

1INTRODUCTION

1.1 General information

The transillumination top 450 mot. has been designed, manufactured and tested in compliance with

DIN EN 61010-1 (IEC 61010-1) and IEC 61010-2-101 Safety requirements for electrical equipment for

measurement, control and laboratory use.

The device conforms to Directives 2006/95/EC “Low Voltage Directive” and 2004/108/EC

“Electromagnetic Compatibility”. The device is disposed of in accordance with the WEEE Directive

2002/96/EC.

It carries the mark.

The operating manual contains all information and warnings the operator must comply with.

The following warning and information symbols are used in this operating manual:

CAUTION

This symbol indicates a potential hazard to the user.

CAUTION

Optical radiation is emitted. Do not look into the laser beam!

This may be harmful to the eyes (see Section 2.3).

CAUTION

Risk of pinching!

CAUTION

Hot surface!

CAUTION: High-energy UV radiation!

Risk of injury to eyes and skin!

CAUTION

Disconnect the instrument from the power supply before opening!

ATTENTION

This symbol indicates a potential hazard to the instrument or system.

NOTE

This symbol indicates an instruction which requires particular attention.

INTRODUCTION

Transillumination top 450 mot. Notes on instrument safety Carl Zeiss

08/2012 435500-9000-701 7

1.2 Notes on instrument safety

The transillumination top 450 mot. is equipped with a power supply unit that enables the use

of mains voltages in the 100 to 240 V ±10% 50/60 Hz range without additional voltage

change.

The power supply unit with plastic housing is designed to conform with protective class I. The

unit may not be used if the housing becomes damaged. The transillumination top

450 mot.

may only be operated with the PSU supplied.

The table power supply should not be brought into contact with moisture. The power supply

must be disconnected from the mains supply before cleaning.

The transillumination top 450 mot. may only be used for the applications described in this

operating

manual. The manufacturer cannot assume any liability for other applications of the

instrument, including those of individual modules or single parts.

Modifications and repairs to this instrument and any devices operated in combination with the

microscop

e must be carried out by our service department or by authorized personnel only. The

manufacturer accepts no liability for damage caused by unauthorized access to the interior of

the instrument. Failure to comply with this shall also render any warranty claims invalid.

The device may only be operated by instructed personnel. The instruments may only be

operated by trained personnel who are aware of the possible dangers involved with microscopy

and the application concerned. The microscope is a high-pre

cision instrument that can be

impaired in its performance or destroyed when handled improperly.

If it is determined that protective measures are no longer effective, the instrument must be

switched off and secured against inadvertent operation. Please

contact a Zeiss service agency or

the Carl Zeiss Microscopy Service to repair the instrument.

Dust and dirt may impair the instrument’s performance. The instrument must be effectively

protected from such influences and covered with the dust cover when not in use. Always check

whether the instrument is switched off before you cover it. Broad temperature fluctuations,

direct sunlight and vibrations should be avoided.

The instruments are not equipped with special devices to protect against corrosive, potentially

infectious, toxic, radioactive or other substances that may be hazardous to health. All legal

regulations must be observed when handling such substances, particularly the relevant national

accident prevention regulations.

Defective instruments are not to be disposed of as ordinary domestic waste. They should be

disposed of in accordance with the relevant regulations.

Samples should also be disposed of in compliance with the relevant legal requirements and

internal operating procedures.

INTRODUCTION

Carl Zeiss Notes on warranty Transillumination top 450 mot.

8 435500-9000-701 08/2012

On microscopes with motorized focusing drive there is a risk of pinching fingers in the work

area when lowering the body of the microscope.

−

Before switching on check that the joystick on the SYCOP 3 is at the zero position and not

swiveled out, and that the foot pedal is clear.

−

Automatic travel can be interrupted by pressing the STOP button on the focusing drive or

the STOP button on the SYCOP 3, moving the joystick on the SYCOP

3 up and down,

turning the knurled wheel on the HIP or pressing the Memory 1 or 2 keys on the HIP.

−Do not reach into the possible travel path of the motorized table. There is a risk of pinching

or injury to the fingers when the table is positioned by the control unit.

The separate operating manuals for the Axio Zoom.V16, HXP 200 C and SYCOP 3 (if used)

must be observed and the general safety requirements complied with.

−Operating Manual Axio Zoom.V16: Order No. 435080-9030-701, English edition

−Operating Manual SYCOP 3: Order No. 435611-9010-701, English edition

When operating the microscope always use the antiglare shield to avoid eye damage due to

scattered light.

Use the UV/antiglare shield (Fig. 1/

). Avoid looking directly into the light beam. This can cause

damage to the eyes and skin.

The transillumination top 450 mot. generates extremely high-

energy light in the visible and

invisible range. The related instructions for safety and use must be strictly adhered to.

1.3 Notes on warranty

The manufacturer guarantees that the instrument is free of material or manufacturing defects when

delivered. Possible defects must be notified to us immediately and steps taken to minimize damage. If

notified of such a defect, the manufacturer is obligated to rectify it at his discretion, either by repairing

the instrument or delivering an intact replacement. No guarantee is provided for defects caused by

natural wear (wearing parts in particular) and improper use.

The instrument manufacturer shall not be liable for damage caused by faulty operation, negligence or

any other tampering with the instrument, particularly the removal or replacement of instrument

components, or the use of accessories from other manufacturers. Such actions will render any warranty

claims invalid.

With the exception of the work described in this operating manual, no maintenance or repair work is to

be carried out on these microscopes. Repairs may only be performed by Carl Zeiss service staff or

personnel specifically authorized by Carl Zeiss. In the event of a problem with the instrument, please

contact the Carl Zeiss microscopy service team or your local Carl Zeiss overseas representative.

DESCRIPTION

Transillumination top 450 mot. Indication for use Carl Zeiss

08/2012 435500-9000-701 9

2DESCRIPTION

2.1 Indication for use

In conjunction with the selected microscope the transillumination top 450 mot. is for examining

translucent preparations by the transmitted light process.

2.2 Package check list with accessories

Name/Order No. Figure Remarks

Transillumination top

450 mot.

435500-9000-000

Antiglare shield

contained in

435500-9000-000

Can be screwed onto the

carrier/nosepiece from the left

or right

Magnet coded receptacle

d = 84 mm

included in

435500-9000-000

For ∅84 mm accessories

Clear glass plate

d = 120 mm

included in

435500-9000-000

Scratch-proof, with strongly

reduced autofluorescence

Assembly aid d = 120 mm

included in

435500-9000-000

For covering the transmitted

light aperture during assembly

Power supply

24 V, 60 W

included in

435500-9000-000

With country-specific power

supply cable

CAN cable RJ 45

included in

435500-9000-000

L = 1000 mm

Foot button S

435602-9010-000

Optional accessories

For connecting to

transillumination top 450 mot.

DESCRIPTION

Carl Zeiss Microscope system… Transillumination top 450 mot.

10 435500-9000-701 08/2012

2.3 Microscope system with transillumination top 450 mot.

Fig. 1 Axio Zoom.V16 with transillumination

top 450 mot.

Axio Zoom.V16 microscope system

AMicroscope body (Axio Zoom.V16) with control

unit (HIP)

BBinocular photo tube

CEyepiece

DObjective

ENosepiece

FIntermediate tube (Fluar Illuminator Z mot.)

GCamera adapter with microscope camera

(AxioCam)

HReflected light illumination (slit-ring illuminator

with cold light source CL 6000 LED)

IUV/visual glare shield

KStand (focus motor with 490 mm profile column

and MaRC control unit on base plate 450)

LTransmitted light illuminator

(transillumination top 450 mot.)

MSpecimen stage (gliding stage)

NSYCOP 3 system control panel

OEMS 3 controller with optional foot pedal S

PPower supply

The items of microscope equipment shown here

are examples and may differ from those

actually provided!

Inhaltsverzeichnis

Andere Zeiss Mikroskop Handbücher

Zeiss

Zeiss OPMI 1 FR pro Gebrauchsanweisung

Zeiss

Zeiss LSM800-2 Bedienungsanleitung

Zeiss

Zeiss LSM 880 Bedienungsanleitung

Zeiss

Zeiss JENAVAL Bedienungsanleitung

Zeiss

Zeiss 880 Installationsanleitung

Zeiss

Zeiss Axiovert 200 Bedienungsanleitung

Zeiss

Zeiss LSM 700 Bedienungsanleitung

Zeiss

Zeiss EM 10 A Bedienungsanleitung

Zeiss

Zeiss opmi lumera 700 Bedienungsanleitung

Zeiss

Zeiss LSM 710 Bedienungsanleitung

Zeiss

Zeiss Axio Zoom.V16 Bedienungsanleitung

Zeiss

Zeiss Colibri 7 Bedienungsanleitung

Zeiss

Zeiss TELAVAL 31 Bedienungsanleitung

Zeiss

Zeiss OPMI Pentero Bedienungsanleitung

Zeiss

Zeiss EN10247 Betriebsanleitung

Zeiss

Zeiss Primostar 3 Bedienungsanleitung

Zeiss

Zeiss Stemi 508 Bedienungsanleitung

Zeiss

Zeiss Stemi 305 cam Bedienungsanleitung

Zeiss

Zeiss LSM 880 with AiryScan FAST Einrichtungshandbuch

Zeiss

Zeiss LSM 880 Bedienungs- und Wartungshandbuch

Zeiss

Zeiss Axiotech Bedienungsanleitung

Zeiss

Zeiss Lattice Lightsheet 7 Bedienungsanleitung

Zeiss

Zeiss AxioObserver D1 Bedienungsanleitung

Zeiss

Zeiss Axioskop Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Olympus

Olympus SZ61 Bedienungsanleitung